Siemens SIMATIC TP700 Comfort Outdoor Compact Operating Instructions
Hide thumbs
Also See for SIMATIC TP700 Comfort Outdoor:
- Operating instructions manual (52 pages) ,
- Compact operating instructions (42 pages) ,
- Operating instructions manual (29 pages)
Table of Contents
Advertisement
Quick Links
Comfort Outdoor
SIMATIC HMI
HMI devices
TP700 Comfort Outdoor,
TP1500 Comfort Outdoor
Compact Operating Instructions
05/2016
A5E35956909-AC
___________________
Preface
___________________
Overview
___________________
Safety instructions
___________________
Mounting and connecting the
HMI device
___________________
Configuring the device
___________________
Commissioning a project
___________________
Maintenance and care
___________________
Technical information
___________________
Technical Support
1
2
3
4
5
6
7
A
Advertisement
Table of Contents
Related Manuals for Siemens SIMATIC TP700 Comfort Outdoor
Summary of Contents for Siemens SIMATIC TP700 Comfort Outdoor
- Page 1 ___________________ Comfort Outdoor Preface ___________________ Overview ___________________ SIMATIC HMI Safety instructions ___________________ Mounting and connecting the HMI device HMI devices TP700 Comfort Outdoor, ___________________ TP1500 Comfort Outdoor Configuring the device ___________________ Commissioning a project Compact Operating Instructions ___________________ Maintenance and care ___________________ Technical information ___________________...
- Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 3: Preface
Operating instructions on the Comfort Panels (http://support.automation.siemens.com/WW/view/en/49313233) Note This document belongs to the device and will also be required for repeat commissioning. - Page 4 Preface Naming conventions Term Applies to System • System Machining center • One or more machines • TP700 Comfort Outdoor • HMI device Device TP1500 Comfort Outdoor • WinCC WinCC V13 SP1 (TIA Portal) Figures This document contains figures of the devices described. The figures can deviate from the particularities of the delivered device.
-
Page 5: Table Of Contents
Table of contents Preface ..............................3 Overview..............................7 Product description ........................7 Software requirements ......................8 Scope of delivery ........................9 Configuration of the devices ....................10 1.4.1 Device views ........................... 10 1.4.2 Interfaces ..........................11 Safety instructions ..........................12 General safety instructions ..................... - Page 6 Table of contents Technical information ..........................25 Certificates and approvals ..................... 25 Electromagnetic compatibility ....................25 7.2.1 Emitted interference ....................... 25 7.2.2 Immunity to interferences ....................... 25 Mechanical ambient conditions ....................26 7.3.1 Storage conditions ......................... 26 7.3.2 Operating Conditions ......................26 Climatic ambient conditions ....................
-
Page 7: Overview
Overview Product description SIMATIC Comfort Outdoor devices with glass touch screen and powder-coated, UV-resistant aluminum front are designed for use in indoor and outdoor areas, for example, in the fields of Oil&Gas, Marine or Refrigeration Technology. All devices offer the same excellent functionality and are configured exclusively with the innovative HMI software, WinCC. -
Page 8: Software Requirements
Overview 1.2 Software requirements Features Front External dimensions of the front and mounting cutout correspond to the • standard product Durable powder coating • High UV resistance • GFG (Glass-Film-Glass) touch screens, analog resistive • Manual or automatic brightness control with brightness sensor •... -
Page 9: Scope Of Delivery
Connector, female, 2-pin, type 1 Some components in the scope of delivery are also available as accessories, see "Accessories" section in the Comfort Panels operating instructions or directly in the Industry Mall (https://mall.industry.siemens.com). TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC... -
Page 10: Configuration Of The Devices
Overview 1.4 Configuration of the devices Configuration of the devices 1.4.1 Device views This section describes the basic design of the device using the example of the TP700 Comfort Outdoor. Front view and side view ① Light sensor ② Aluminum front, powder coated ③... -
Page 11: Interfaces
Overview 1.4 Configuration of the devices 1.4.2 Interfaces Position of the interfaces The figure below shows the interfaces of the HMI devices. ① ⑤ X80 power supply connector X1 PROFINET (LAN), 10/100 Mb ② ⑥ Connection for equipotential bonding (ground) X90 Audio Line IN / OUT ③... -
Page 12: Safety Instructions
Safety instructions General safety instructions The general safety instructions in the "Comfort Panel" operating instructions apply. Also note the following for Comfort outdoor devices: WARNING Unintended functions may be triggered with icing If the operating temperature is below 2 °C, icing may occur on the front of the device. Icing may trigger unintended functions in some circumstances. -
Page 13: Notes About Usage
Safety instructions 2.2 Notes about usage Notes about usage Industrial applications The HMI device is designed for outdoor areas in industrial applications. It conforms to the following standards: ● Requirements of the emission standard for industrial environments, EN 61000-6-4: 2007 + A1:2011 ●... -
Page 14: Mounting And Connecting The Hmi Device
A damaged part will cause the HMI device to malfunction. Do not install parts damaged during shipment. In the case of damaged parts, contact your Siemens representative. Check the scope of supply of the HMI device (see Scope of delivery (Page 9)). -
Page 15: Checking The Operating Conditions
Mounting and connecting the HMI device 3.1 Preparing for installation 3.1.2 Checking the operating conditions Note the following aspects before installing the HMI device: 1. Familiarize yourself with the technical specifications for operating the HMI device. You can find this information in the section "Technical information (Page 25)". 2. - Page 16 Mounting and connecting the HMI device 3.1 Preparing for installation Mounting position Select one of the approved mounting positions for your device. The approved mounting positions are described in the following sections. Mounting in horizontal format Ambient temperature when mounted in horizontal format: ●...
-
Page 17: Checking Clearances
Mounting and connecting the HMI device 3.1 Preparing for installation 3.1.4 Checking clearances The following clearances are required around the HMI device to ensure sufficient self- ventilation: ● At least 15 mm to both the right and left of the mounting cutout (in x direction) to allow for insertion of the mounting clips during installation ●... - Page 18 Mounting and connecting the HMI device 3.1 Preparing for installation Degrees of protection The degrees of protection of the HMI device can only be guaranteed if the following requirements are met: ● Material thickness at the mounting cutout for a protection rating of IP66 or Front face only Type 4X/Type 12 (Indoor/Outdoor): 2 mm to 6 mm ●...
-
Page 19: Mounting The Device
Mounting and connecting the HMI device 3.2 Mounting the device Mounting depth The mounting depth of the devices is: HMI device Mounting depth TP700 Comfort Outdoor 67 mm TP1500 Comfort Outdoor 77 mm Mounting the device Positions of the mounting clips To achieve the degree of protection for the HMI device, the positions for the mounting clips shown below must be adhered to. -
Page 20: Connecting The Device
Mounting and connecting the HMI device 3.3 Connecting the device Procedure Note Risk of guaranteed degree of protection not being met If the mounting seal is damaged, the degree of protection is not guaranteed. Replace the device in this case. Note Installation of the HMI device Always mount the HMI device according to the instructions in this manual. -
Page 21: Configuring The Device
Configuring the device Overview The specifications in the "Comfort Panel" operating instructions apply for commissioning and parameter assignments. The enhanced brightness control of the Comfort Panels Outdoor differs from the other Comfort HMI devices and is described in the following section. Changing the brightness settings The Comfort Outdoor Panels feature a manual or automatic brightness control with a brightness sensor. - Page 22 Configuring the device 4.2 Changing the brightness settings Select the "Manual" or "Auto" option. – In the "Manual" mode, you can adjust the brightness to the desired value using the slider. Note "Manual" mode A change in the brightness value through the configuration takes precedence over the manual setting.
-
Page 23: Commissioning A Project
Commissioning a project Overview The specifications in "Comfort Panels" operating instructions apply. Using existing projects Proceed as follows to transfer an existing project to the HMI device: 1. Open the existing project in WinCC (TIA Portal). 2. Make sure that the project is dimensioned within the functional scope of the HMI device, see section "Scope of functions with WinCC (Page 33)". -
Page 24: Maintenance And Care
Maintenance and care Cleaning the device The specifications in "Comfort Panels" operating instructions apply. NOTICE Disable or switch off the device while cleaning Switch off the HMI device or activate the clean screen when you clean the appliance during operation. Note Cleaning of the coated glass touch screen Take care not to damage the glass touch screen and the coating of the touch screen on... -
Page 25: Technical Information
Technical information Certificates and approvals Approvals The device is certified as shown on the rear of the device. As soon as additional certificates are available, you can find them in the Industry Mall or Technical Support. Search for your device and use the link "Support > Approvals / Certificates". Electromagnetic compatibility The device is designed for industrial use. -
Page 26: Mechanical Ambient Conditions
Technical information 7.3 Mechanical ambient conditions Mechanical ambient conditions 7.3.1 Storage conditions The following information is for a device that is transported and stored in its original packaging. The device meets the requirements according to IEC 60721-3-2 Class 2M2 with the following amendments and limitations: Type of condition Permitted range... -
Page 27: Transport And Short-Term Storage
Technical information 7.4 Climatic ambient conditions 7.4.2 Transport and short-term storage The following information applies to a device that is transported in the original packaging and weather-proof packaging, and stored from some time. The device meets the requirements according to IEC 60721-3-2 Class 2K4 with the following amendments and limitations: Type of condition Permitted range... -
Page 28: Information On Insulation Tests, Protection Class And Degree Of Protection
Technical information 7.5 Information on insulation tests, protection class and degree of protection Information on insulation tests, protection class and degree of protection Insulation test The insulation strength is demonstrated in the type test with the following test voltages in accordance with IEC 61131-2: Circuits with rated voltage of U Test voltage... -
Page 29: Dimension Drawings
Technical information 7.6 Dimension drawings Dimension drawings 7.6.1 Dimension drawings of the TP700 Comfort Outdoor TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC... -
Page 30: Dimension Drawings Of The Tp1500 Comfort Outdoor
Technical information 7.6 Dimension drawings 7.6.2 Dimension drawings of the TP1500 Comfort Outdoor TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC... -
Page 31: Specifications
Technical information 7.7 Specifications Specifications Weight TP700 Comfort Outdoor TP1500 Comfort Outdoor Weight without packaging approx. 1.5 kg 4.0 kg Display TP700 Comfort Outdoor TP1500 Comfort Outdoor Type LCD TFT Active display area 7.0'' 15.4'' 152 mm x 91 mm 331 x 207 mm Resolution 800 x 480 pixels... -
Page 32: Description Of The Ports
Technical information 7.8 Description of the ports Interfaces TP700 Comfort Outdoor TP1500 Comfort Outdoor 1 x RS 422/485 (PROFIBUS) Max. 12 Mbps, applies to DP operations Ethernet (PROFINET) 2 x RJ45 10/100 Mbps Audio Line In and Line Out USB 2.0 2 x Host 1 x Device With integrated switch (one IP address only) -
Page 33: Scope Of Functions With Wincc
Technical information 7.9 Scope of functions with WinCC Scope of functions with WinCC The tables below show the objects which can be integrated in a project for an HMI device. Note The specified values are maximum values of the individual objects. Simultaneous use of multiple objects with their maximum value can lead to problems in the active project. - Page 34 Technical information 7.9 Scope of functions with WinCC Screens Object Specification TP700 Comfort Outdoor, TP1500 Comfort Outdoor Screens Number Objects per screen Tags per screen Complex objects per screen (for example, bars) Template Recipes Object Specification TP700 Comfort Outdoor, TP1500 Comfort Outdoor Recipes Number Data records per recipe...
- Page 35 Technical information 7.9 Scope of functions with WinCC Note Data consistency If the HMI device is switched off, the consistency of the stored data is only ensured with "SIMATIC HMI Memory Card" type memory cards. With commercially available memory cards, switching off the device may result in the loss of saved data, for example, due to a power failure.
-
Page 36: Technical Support
You can find additional information and support for the products described on the Internet at the following addresses: ● Technical support (http://www.siemens.de/automation/csi_en_WW) ● Support request form (http://www.siemens.com/automation/support-request) ● After Sales Information System SIMATIC IPC/PG (http://www.siemens.com/asis) ● SIMATIC Documentation Collection (http://www.siemens.com/simatic-tech-doku-portal) ● Your local representative (http://www.automation.siemens.com/mcms/aspa-db/en/Pages/default.aspx) ●... -
Page 37: Index
Index Emission, 13 Accessories, 9 Alarm buffer, 33 ALARM_S, 33 Alarms, 33 Figure, 4 Approvals, 25 HMI device Clearance, 17 Brightness Mounting, 20 Changing, 21 Technical specifications, 31 Brightness setting, 35 HMI devices Input device, 31 Interfaces, 32 Changing Memory, 31 Brightness, 21 HMI devices Color depth, 21... - Page 38 Index Memory Tags, 33 HMI devices, 31 Technical specifications Mounting Display, 31 HMI device, 20 HMI devices, 31 Mounting clip Input device, 31 Mounting, 19 Interfaces, 32 Mounting cutout Memory, 31 Compatibility, 18 Power supply, 32 Dimensions, 18 Text objects, 35 Preparing, 18 Touch screen calibration, 35 Mounting position, 16...