Basic Operation; Turning On And Off The Device; Adjusting The Radio Volume; Adjusting The Squelch Level - Garmin VHF 110 Series Owner's Manual

Icon Status
Weather alert
External GPS connected

Basic Operation

Turning On and Off the Device

Hold PWR.
TIP: You can set the device to turn on automatically
Settings, page 9).

Adjusting the Radio Volume

1 Set the squelch level to MIN before you adjust the radio
volume (optional).
2 Turn the VOL/SQ dial to increase or decrease the radio
volume.

Adjusting the Squelch Level

You can adjust the sensitivity level of the squelch to filter out
background noise. When you increase the squelch level, you
hear fewer weak background signals when you are receiving.
1
Press the VOL/SQ dial.
SQUELCH appears on the screen.
2 Turn the VOL/SQ dial counter-clockwise until you hear audio.
3
Turn the VOL/SQ dial clockwise until there is no background
noise.

Selecting the Frequency Band

You can switch between the USA, International, or Canadian
frequency bands (Channel Lists, page
NOTE: Not all frequency bands are available on all device
models.
1
Select MENU > CHANNEL > FREQUENCY BAND.
2
Select a frequency band.

Selecting a Channel

You can select an International, Canadian, or USA channel
(Selecting the Frequency Band, page
Select an option:
• To select a channel on the device, turn the SELECT dial.
• To select a channel on the handset, select

Transmitting with the Radio or Handset

1
Select an appropriate channel.
2
Ensure the channel is clear.
NOTE: You cannot obstruct the communications of other
people due to Federal Communications Commission (FCC)
and international guidelines.
3
Select PTT on the handset.
appears at the top of the screen.
4
Speak into the handset.
NOTE: Five minutes is the maximum time allowed for
transmission. After five minutes of transmitting, PTT is
disabled until you release PTT.
5 Release PTT.
Bypassing the Low Transmission Power
Setting
In the USA frequency band, transmissions on channels 13 and
67 are required to be low-power (1 W) by default, because they
2
(System
10).
2).
or .
are intended for intership (bridge-to-bridge) communication. If
other radios cannot receive these channels due to the low power
setting, you can bypass the default restriction.
1 From USA channels 13 or 67, select PTT.
2
While transmitting, select 25W.

Scanning and Saving Channels

Scanning All Channels

When you scan channels, the radio searches for channels that
are broadcasting. When a channel is broadcasting, the radio
pauses on that channel until the broadcast stops. After four
seconds of inactivity on a channel, the radio resumes scanning.
NOTE: When you turn on ATIS
Identification System, page
save channels.
1
Select SCAN > ALL.
2 Select an option:
• To exclude the currently active channel from subsequent
passes and resume scanning, select SKIP.
• To scan channel 16 each time another channel is
scanned, select +CH16.
For example, the radio scans channel 21, channel 16,
channel 22, channel 16, and so on.
+CH16 appears on the device screen.
• To scan channel 16 in its usual order, select -CH16.
For example, the radio scans channel 14, channel 15,
channel 16, channel 17, and so on.
• To end the scan, select EXIT.
The radio stops scanning and tunes to the last used,
active channel.

Saving a Channel

You can save any channel except the weather (WX) channels.
You can save an unlimited number of channels.
1 Select SCAN.
2
Turn the SELECT dial until you find a channel you want to
save.
3
Select SAV CH.
appears above a saved channel.

Removing a Saved Channel

1
Select SCAN.
2
Turn the SELECT dial until you find a saved channel.
NOTE: A saved channel has
3
Select SAV CH.

Scanning Saved Channels

You can scan only the channels you have saved. When a saved
channel is broadcasting, the radio pauses on that channel until
the broadcast stops. After four seconds of inactivity on a
channel, the radio resumes scanning.
NOTE: When you turn on ATIS
Identification System, page
save channels.
1
Select SCAN > SAVED.
2
Select an option:
• To exclude the currently active channel from subsequent
passes and resume scanning, select SKIP.
• To scan channel 16 each time another saved channel is
scanned, select +CH16.
For example, the radio scans saved channel 21, channel
16, saved channel 25, channel 16, and so on.
+CH16 appears on the device screen.
(Automatic Transmitter
8), the radio does not scan or
above it.
(Automatic Transmitter
8), the radio does not scan or
Basic Operation