Turning On And Off Atis; Viewing Your Atis Identification Number; Automatic Identification System; Turning On And Off Ais - Garmin VHF 110 Series Owner's Manual

1
Select MENU > ATIS > MY ATIS ID.
2
Enter your ATIS number
3
Select ACCEPT.
The radio prompts you to reenter your number.
4 Enter your ATIS number again, and select ACCEPT.
If the ATIS numbers you entered do not match, a message
appears.
5
If necessary, select RETRY and enter the number again.

Turning On and Off ATIS

1
Select MENU > ATIS > ATIS.
2
Select ON or OFF.
appears on the screen when ATIS is enabled.
3 Select OK.

Viewing Your ATIS Identification Number

Select MENU > ATIS > MY ATIS ID.

Automatic Identification System

The Automatic Identification System (AIS) is an automatic
tracking system used on vessels and by vessel traffic services
(VTS). It enables vessels and VTS to identify and locate vessels
by electronically exchanging data with other nearby vessels and
AIS base stations. When used with a compatible chartplotter or
multifunction display (MFD), AIS can assist with collision
avoidance.
NOTE: AIS is not available on all models.

Turning On and Off AIS

1
Select MENU > AIS.
2
Select ON or OFF.
3
Select OK.

NMEA 0183 and NMEA 2000

When you connect the radio to a NMEA 0183 device or a NMEA
2000 network, you can transfer received DSC distress and
position information to any compatible connected chartplotter
(NMEA, page 16).
The radio can also receive GPS-position information from a
NMEA 0183 device or a NMEA 2000 network. Received GPS-
position information appears on the home screen and is
transmitted with DSC calls.
data is available, and flashes when GPS data is not present.
When GPS data is not present, you must enter your position
manually (Manual Position Information, page
For more information on connecting the radio to a NMEA 0183
device or a NMEA 2000 network, see the VHF 110/210 AIS
Series Installation Instructions.
Additional Functionality with Other Garmin
Devices
The radio has additional capabilities when you connect it to
other Garmin devices, such as a chartplotter.
NOTE: You may need to upgrade your Garmin chartplotter
software to use NMEA 0183 or NMEA 2000 features.
When you connect the radio to a Garmin chartplotter using
either NMEA 0183 or NMEA 2000, your chartplotter keeps track
of the current and previous positions of the contacts in the
directory.
When you connect the radio to the same NMEA 2000 network
as a Garmin chartplotter, you can use the chartplotter to set up
an individual routine call.
Automatic Identification System
(Entering Text, page 4).
appears on the screen when GPS
8).
When you connect the radio to the same NMEA 2000 network
as a Garmin chartplotter, and you initiate a man-overboard
distress call from the radio, the chartplotter prompts you to
navigate to the man-overboard location. If you connect a Garmin
autopilot system to the same NMEA 2000 network, the
chartplotter prompts you to start a Williamson's turn to the man-
overboard location.
Communicating Over NMEA 0183 or NMEA
2000
NOTE: This feature is not available on all models.
You can select a connection either to a NMEA 0183 device or to
a NMEA 2000 network. The radio can communicate over only
one communication protocol at a time.
1 Select MENU > COMMUNICATIONS > PROTOCOL.
2
Select NMEA0183 or NMEA2000.

Configuring DSC NMEA Transmissions

You can filter the types of DSC-call data the radio sends to a
connected NMEA 0183 device or over a NMEA 2000 network.
1
Select MENU > COMMUNICATIONS > DSC OUTPUT.
2
Select an option:
• To send NMEA data when you receive a DSC call from
any MMSI number, select ALL VESSELS, and proceed to
the last step.
• To disable sending NMEA data when you receive a DSC
call, select NO VESSELS, and proceed to the last step.
• To send NMEA data only when you receive a call from a
vessel in your directory, select SELECT VESSELS, and
proceed to the next step.
NOTE: When you configure the radio for SELECT
VESSELS, all received DSC-distress-call data is sent over
NMEA, even if the vessel is not in your directory.
3
Select a vessel in your directory.
4 Select an option:
• To send all DSC-call data from this vessel, select ON.
®
• To send DSC-distress-call data only from this vessel,
select OFF.
5
Repeat this process for each vessel in your directory.
6
Select BACK to save your changes and exit the menu.
Select MENU > SYSTEM.
DISPLAY: Sets the backlight and contrast levels.
BEEPER: Sets the volume or disables the beeper tone that
sounds when you press a key or turn a dial.
AUTO POWER-ON: Sets the radio to turn on automatically
when it receives power.
LANGUAGE: Sets the language for the radio.

Number Settings

You can customize the numbers shown on the home screen of
the radio.
Select MENU > SYSTEM > NUMBERS.
LAT/LONG: Shows or hides the latitude and longitude numbers
from either a connected GPS device, or from manually
entered position data.
TIME: Shows or hides the time received from a connected GPS
device or entered manually.
NOTE: The time updates automatically only if you connect a
GPS device. When you enter your time and position
manually, the time shown does not update automatically. For

System Settings

9