Docomo F-04B Instruction Manual page 154

Upper slot : Command
Lower slot : Example
AT&D<n>
AT&D2
OK
AT&E<n>
AT&E1
OK
AT&F
AT&F
OK (When in offline mode)
AT&S<n>
AT&S0
OK
AT&W
AT&W
OK
AT＊DANTE
AT＊DANTE
＊DANTE : 3
OK
AT＊DGANSM=<n>
AT＊DGANSM=0
OK
AT＊DGAPL=<n> [,<cid>]
AT＊DGAPL=0,1
OK
AT＊DGARL=<n> [,<cid>]
AT＊DGARL=0,1
OK
AT＊DGPIR=<n>
AT＊DGPIR=0
OK
AT＊DRPW
AT＊DRPW
＊DRPW : 0
OK
*1
Set the operation performed when circuit ER (DTR) signal received from DTE is switched
from ON to OFF while online data mode takes effect.
n=0 : Ignore status (status is always considered to be ON)
n=1 : Move to online command mode when status changes from ON to OFF
n=2 : Disconnect line and move to offline mode when status changes from ON to OFF
(default)
*1
Set the speed display used when connection is made.
n=0 : Display communication speed of wireless zone
n=1 : Display communication speed between a PC and FOMA terminal (default)
Reset the current setting to the default.
When this command is executed during communication, the terminal is reset after the line
is disconnected (displaying "NO CARRIER").
*1
Set control of the data set ready (DR) signal to be output to DTE.
n=0 : Always ON (default)
Register the current settings in FOMA terminal.
Indicate FOMA terminal reception level in the "＊DANTE : <n>" format.
n=0 : Out of service area
n=1 : Received signal level of FOMA terminal is 0 or 1 antenna.
n=2 : Received signal level of FOMA terminal is 2 antennas.
n=3 : Received signal level of FOMA terminal is 3 antennas.
AT＊DANTE=? : Display a list of displayable values
*2
Set to reject or permit incoming packet communications.
n=0 : Reject setting = OFF, Accept setting = OFF (default)
n=1 : Reject setting=ON
AT＊DGANSM? : Display current settings
AT＊DGANSM=? : Display a list of assignable values
*2
Set the dialup connections (APN) to permit incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN permitted for incoming communications
n=1 : Delete from list of APN permitted for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT＊DGAPL? : Display current settings
AT＊DGAPL=? : Display a list of assignable values
*2
Set the dialup connections (APN) to refuse incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN rejected for incoming communications
n=1 : Delete from list of APN rejected for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT＊DGARL? : Display current settings
AT＊DGARL=? : Display a list of assignable values
*2
Set Caller ID notification when packet communication connection is being performed. This
command is available when a communication is sent or received.
n=0 : Connect to APN directly (default)
n=2 : Connect to APN prefixing 186
When Show/Hide caller ID is specified by dialup network→P23
AT＊DGPIR? : Display current settings
AT＊DGPIR=? : Display a list of assignable values
Indicate an index for the reception power of the radio waves that FOMA terminal receive.
AT＊DRPW=? : Display a list of displayable values
Description
n=1 : ON at time of connection
n=2 : Accept setting=ON
n=1 : Connect to APN prefixing 184
38