Page 32
動作環境の最新情報については、 ドコモのホームページにてご確認く ださい。 動作環境を確認する 本FOMA端末を利用するための動作環境は以下のとおりです。 お知らせ 項目 必要環境 • 動作環境によっては、ご使用になれない場合があります。また左記 動作環境以外でのご使用によるお問い合わせおよび動作保証は、当 パソコン本体 • PC/AT互換機、および、Macで、CD- 社では責任を負いかねますので、あらかじめご了承ください。 ROMドライブが使用できるコンピュータ • USBポート(Universal Serial Bus Specification Rev1.1/2.0準拠) • USBハブ(モニタやキーボードなどにある USBポートを含む)を経由しての動作は保 証いたしかねます。 • ディスプレイ解像度800×600ドット、 High Color (65.536) 以上を推奨 ※ Windows 2000 SP4以降(日本語版) Windows XP SP2以降(日本語版) Windows Vista SP1以降(日本語版) ※3 Mac OS X 10.4.11 (日本語版) ※3 Mac OS X 10.5.6 (日本語版) ※2 必要メモリ Windows 2000 : 64Mバイト以上 Windows XP : 128Mバイト以上 Windows Vista : 512Mバイト以上 Mac OS X 10.4.11:512Mバイト以上 Mac OS X 10.5.6:512Mバイト以上...
Page 52
■ 電源 電源電圧 主な仕様 DC5V±5%(パソコンより給電) 消費電流 ■ 対応OS 通信時最大消費電流 Windows 2000 Professional日本語版 (Service Pack 4以降) 3G:約550mA 以下 Windows XP Home Edition日本語版(Service Pack 2以降) GSM/GPRS:約300mA 以下 Windows XP Professional日本語版(Service Pack 2以降) 通信時平均消費電流 Windows Vista 32 bit日本語版(Service Pack 1以降) 3G:約260mA 以下 Windows Vista 64 bit日本語版(Service Pack 1以降) GSM/GPRS:約260mA 以下 Mac OS X 10.4.11 日本語版 待ち受け時平均消費電流 Mac OS X 10.5.6 日本語版 3G:約90mA 以下 GSM/GPRS:約90mA 以下 ■ 通信速度 ※ 使用状況により、消費電流は変動します。 パケット通信: 受信最大7.2Mbps(ベストエフォート方式) ■ 形状 USB接続タイプ 送信最大5.7Mbps(ベストエフォート方式) ※ 通信速度は、送受信時の技術規格上の最大値であり、実際の通信 ■ サイズ 速度を示すものではありません。ベストエフォート方式による提 高さ:約80mm 供となり、実際の通信速度は、通信環境やネットワークの混雑状...
Page 53
FCC Regulations 輸出管理規制 Statement 本製品及び付属品は、日本輸出管理規制( 「外国為替及び外国貿易法」 及びその関連法令)の適用を受ける場合があります。また米国再輸出 This equipment has been tested and found to comply with 規制(Export Administration Regulations)の適用を受けます。 the limits for a class B digital device, pursuant to Part 15 本製品及び付属品を輸出及び再輸出する場合は、 お客様の責任及び費 of the FCC Rules. These limits are designed to provide 用負担において必要となる手続きをお取りください。 詳しい手続きに reasonable protection against harmful interference in a ついては経済産業省または米国商務省へお問合せください。 residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause European Union Directives Conformance harmful interference to radio communications. However, Statement there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be Hereby, LG Electronics Inc. declares that this determined by turning the equipment off and on, the user is product is in compliance with: encouraged to try to correct the interference by one or •The essential requirements and other relevant more of the following measures: provisions of Directive 1999/5/EC • Reorient or relocate the receiving antenna. •All other relevant EU Directives • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. The above gives an example of a ...
Page 54
The standards include a substantial safety margin Class B Compliance designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless This device and its accessories comply with part15 of FCC devices employs a unit of measurement known as the rules. Specific Absorption Rate, or SAR. Operation is subject to the following two conditions: The SAR limit set by the FCC is 1.6W/kg. • This device & its accessories may not cause harmful ※ Tests for SAR are conducted using standard operating interference. positions specified by the FCC with the device • This device & its accessories must accept any interference transmitting at its highest certified power level, the actual received, including interference that may cause undesired SAR level of the device while operating can be well below operation. the maximum value. This is because the device is designed to operate at multiple power levels so as to use Body-worn Operation only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the This device has been tested for typical body-worn lower the power output. operations with the distance of 0.19inches (0.5cm) from Before a device is available for sale to the public, it must be the user's body. tested and certified to the FCC that it does not exceed the To comply with FCC RF exposure requirements, a minimum limit established by the government-adopted requirement separation distance of 0.19inches(0.5cm) must be for safe exposure. The tests are performed in positions and maintained from the user's body. locations (e.g., worn on the body) as required by the FCC Consumer Information on SAR (Specific Absorption for each model.
Page 57
INSTRUCTION MANUAL for Connection Guide L-05A Data Communication Device ...
Page 58
1. Learning the precautions. . . . . . . . . . . . . . . . . . . . . . P63 penetrate, such as tunnels, underground passages and some buildings in areas where radio wave signals are weak or out of 2. Learning the names of parts and functions of the the service area. Even when you are on a higher floor of a tall FOMA terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P72 building or condominium and nothing blocks your view outside, 3. Inserting the FOMA terminal into a PC . . . . . . . . . . P78 the FOMA terminal may not be able to receive or transmit 4. Having the FOMA terminal recognized by your PC. . . P78 signals. Also communication may be interrupted even when the 5. Setting up the FOMA terminal for communication Antenna Indication Lamp on the FOMA terminal lights green . . . . . . . . . . . "L-05A INSTRUCTION MANUAL (PDF)" P60 indicating a strong signal reception with 3 antenna indication bar. The latest version of this manual can be downloaded from the • Use the FOMA terminal in ways that do not disturb others in DOCOMO website. public places, crowded locations, or quiet locations. • The FOMA terminal communicates via radio waves by ■ The URL of PDF for INSTRUCTION MANUAL converting voices into digital signals. If you move into an area http://www.nttdocomo.co.jp/english/support/manual/ index.html where signal reception is poor, the digital signals may not be ...
Page 59
How to Read/Refer to This Manual Contents L-05A Manual is composed of "L-05A INSTRUCTION MANUAL〜Connection Guide〜" (this manual) and "L-05A INSTRUCTION MANUAL (included CD-ROM)" recorded in CD-ROM. ■ "L-05A INSTRUCTION MANUAL〜Connection Guide〜"(this manual) The following contents such as connection to computer, troubleshooting methods, specifications of L-05A are written. • Contents/Precautions • Before Using the FOMA Terminal • Setting up • Appendix/Troubleshooting ■ "L-05A INSTRUCTION MANUAL (included CD-ROM)" Besides the above contents described in "L-05A INSTRUCTION MANUAL〜Connection Guide〜", the contents of configuring communication through special application are also written. This manual is supplied with PDF. To view this manual, Adobe Reader (Version6.0 or later is recommended) is necessary. • L-05A Connection Software • DOCOMO Connection Manager • Configuring Network Manually • Overseas Use...
Page 60
How to Refer to This Manual This manual offers you the following methods to easily find a page describing functions or services you want to know about. P110 From the Index See next Search from the index when you know the names of functions or services. page for detailed Front descriptions From the Tabs on the Cover cover Search functions or services from the index tabs printed on the front cover. From the Contents Search from the contents that categorize functions. From the Main Features Search from the features when you want to use specific functions. ・ Please understand that "L-05A Manual" refers to the "L-05A" as the "FOMA Terminal". ・ This manual describes, some steps and screens may differ depending on your operating environment. ・ Reprinting all or parts of this manual is prohibited. ・ Information contained in this manual is subject to change without prior notice.
Page 61
A way to find a destination page is explained with an example of installing L-05A connection software on Windows (including a driver). From the The page To next page describing Index installation of L-05A P110 connection software on Search or a function Windows name or a service (including a driver)" name as shown below. From the Index Tabs on the Front Cover Front cover Search for the function in the order of "Front cover"→ "Chapter title page"→ "Target page" as shown below.
Page 62
Displays a section title. Explains Useful Operation steps Information or suggestions relating to an operation. A key screen for an operation step. This is an image of a screen seen on the PC. Numbers, settings or characters entered are for reference only. Index: ※:The above page is an example. Searching each ※:Screen images and illustrations contained in this chapter is available. manual are for reference only. They may differ from those seen for the actual product.
Page 63
Contents How to Read/Refer to This Manual ・・・・・・・・・・・・・・・・ 57 Contents ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 61 Features of the L-05A・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 62 Safety Precautions (ALWAYS FOLLOW THESE PRECAUTIONS) ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 63 Handling and Care・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 68 Basic package ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 70 Names of Parts and Functions Before Using Using FOMA Card the FOMA Available Communications Terminal Connecting FOMA Terminal with a PC Setting Up Setting Up Windows version Macintosh version Troubleshooting Error Messages Appendix/ Warranty and After-Sales Service Trouble- Software update shooting Main Specifications Export Administration Regulations Intellectual Property Rights Index...
Page 64
Features of the L-05A FOMA (Freedom Of Mobile multimedia Access) is the name of a service provided by DOCOMO based on the W-CDMA system, which is certified as one of the global standards of 3rd generation mobile communication systems (IMT-2000). ■ Correspondence with the FOMA HIGH-SPEED Area ■ International Roaming Service You can enjoy high speed communication (Best effort Data communications are available from a PC or system)at a maximum of 7.2Mbps for receiving and sending and receiving SMS even in foreign countries 5.7Mbps for sending. that have adapted the W-CDMA (3G) network system • Communication speed is theoretical values when sending or GSM/GPRS network. and receiving data which does not show the actual ones. "L-05A INSTRUCTION MANUAL (PDF)" P102 The actual communication speed depends on ※ If you subscribed to the FOMA service after September communication environment and network congestion. 1, 2005, a separate subscription is not required. • For details of areas supporting a maximum of 5.7Mbps However, if you unsubscribed to the FOMA service for sending, view DOCOMO website. subscription or canceled the service, a separate • Sending and receiving data may become 384kbps even subscription is required. in the FOMA HIGH-SPEED area. ※ If you initially subscribed to the FOMA service before • Sending and receiving data become 384kbps in FOMA August 31, 2005, and have not subscribed to "WORLD area out of FOMA HIGH-SPEED area. WING", a separate subscription is required. • DOCOMO offers Internet connection services, such as ...
Page 65
■ The following symbols indicate special warnings regarding product usage. Safety Precautions (ALWAYS FOLLOW THESE PRECAUTIONS) Denotes things not to do (prohibition). ■ Before using your FOMA terminal, read these ″Safety Precautions″carefully so that you can use it properly. Denotes not to disassemble. After reading the safety precautions, keep this manual in Not di s assembl y a safe place for later reference. ■ These precautions are intended to protect you and Denotes not to use where it could get others around you. Read and follow them carefully to wet. Not liquids avoid injury, damage to the product or damage to property. ■ The signs below indicate the levels of danger or damage Denotes mandatory instructions that may occur if the particular precautions are not (matters that must be complied with). observed . This sign indicates that ■ "Safety Precautions" are explained in the following incorrect handling has a DANGER 4 sections. high possibility of General Precautions for the FOMA Terminal and FOMA causing death or serious ...
WARNING General Precautions for the FOMA Terminal and FOMA Card Do not put the FOMA terminal or FOMA card in microwave ovens or other heating. The FOMA terminal may over heat, smoke Do not use or leave the FOMA terminal or catch fire, or its circuit parts may burst. and FOMA card in places with a high temperature such as in cars under the blazing sun. Do not throw the FOMA terminal or FOMA Deformation, malfunction heating or the card, or subject them to severe shocks. deterioration of performance may result. Malfunction or fire may result. Also, part of the case could get heated, causing bare skin burns. Be careful not to let electro conductive materials (metal pieces, pencil leads etc.) Do not disassemble. Disassemble, contact with the connector terminal. Also, remodel or solder the terminal and FOMA make sure that these are not entered into card. Not di s assembl y the inside of the FOMA terminal. Fire, injury, electric shock or malfunction Fire or other malfunctions may result from may result. a short circuit. Do not let FOMA terminal and FOMA Make sure you have the power of the card get wet. computer which is connected with FOMA Contact with water or other liquids may Not liquids terminal switched off before you go near a ...
CAUTION Precautions for the FOMA Terminal Do not place the FOMA terminal or FOMA card on unstable locations such as wobbly WARNING tables or slanted locations. The FOMA terminal or FOMA card may fall, Do not put the FOMA terminal in the place resulting in injury or malfunction. where it could be affected by an expanded airbag, e.g. on the dashboard. If the airbag expands, the FOMA terminal Do not store the FOMA terminal or FOMA could hit you and others, causing card in humid or dusty places, or in hot accidents such as injury and the FOMA areas. terminal could get malfunction or Malfunction may result. damaged. If children use the FOMA terminal or Do not place the terminal in breast or FOMA card, a guardian should explain the inner pocket when electronic medical precautions and correct operations. The equipment is near by. guardian should also make sure that the Using FOMA terminal closed to electronic instructions are followed during use. medical equipment may result malfunction. Injury may result. Do not allow liquids such as water, or Keep out of reach of babies and infants. foreign materials such as metal pieces or Accidental swallowing or injury may result. flammable materials to get into the FOMA card opening in the FOMA terminal. Fire, electronic shock or malfunction may result. Contents/Precautions...
Turn off the FOMA terminal in places CAUTION where use is prohibited such as airplanes or hospitals. Electronic devices in some types of cars Electronic and electronic medical can be affected by use of the FOMA appliances may be adversely affected. terminal. For use inside medical facilities, make sure For safety's sake, do not use the FOMA that you comply with their regulations. terminal inside such cars. Remove FOMA terminal from the USB port Itching, rash or eczema may be caused in places near high-precision electronic depending on your physical conditions or devices or devices using weak electronic predisposition. signals. If an abnormality occurs, stop using the The FOMA terminal may possibly cause FOMA terminal immediately, and then seek these devices to malfunction. medical attention. ※ Electronic devices that may be affected Hearing aids, implanted cardiac pacemakers, implanted defibrillators, other medical Metal(chrome plating) is used to the electronic devices, fire alarms, automatic doors and other automatically controlled following parts. devices. Parts that are used: USB connector If you are using an implanted cardiac pace maker, implanted defibrillator or any other electronic medical device, consult the manufacturer or retailer of the device for advice regarding possible effects from radio waves.
Turn off the PC in crowded trains or other public places where implanted cardiac Notes on Using near Electronic Medical pacemaker or defibrillator wearers could Equipment be nearby. Signals from the FOMA terminal may ■The description below meets ″Guideline on the affect the operation of implanted cardiac Use of Radio-communication Equipment such as pacemakers or defibrillators. Cellular Telephones - Safeguards for Electronic Medical Equipment″ by the Electromagnetic Compatibility Conference. If you use an implanted cardiac pacemaker or implanted defibrillator, use the mobile terminal 22cm or more away WARNING from the implanted cardiac pacemaker or implanted defibrillator. Be sure to adhere to the following Operation of an implanted cardiac regulations inside medical facilities. pacemaker or implanted defibrillator may ●Keep the FOMA terminal out of operating be affected by radio waves. rooms, intensive care units (ICUs) or coronary care units (CCUs). ●Turn off the PC in hospital wards. Patients using electronic medical equipment other than implanted cardiac ●Turn off the PC in hospital lobbies and corridors if electrical medical devices pacemakers or implanted defibrillators (using outside medical facilities for could be nearby. treatment at home, etc.) should check the ●If the medical facility has specific zones influence of radio waves upon the where use or possession of mobile equipment by consulting the ...
Page 70
The FOMA terminal should be used within a malfunctions deemed to be caused by water are ° ° temperature range from 5 C to 35 C and a not covered by the warranty, and may be humidity range from 45 % to 85 %. impossible to repair. Since these malfunctions are ■FOMA terminal may affect fixed phones, not under warranty, even when repair is possible, televisions or radios in use nearby. Use as far as it will be done at the user's expense. possible from such appliances. ■Clean the FOMA terminal with a dry, soft cloth ■Keep a separate record of any information stored (Lens cleaning cloth). on the FOMA terminal and store the copies in a If the FOMA terminal is wiped with alcohol, paint safe location. thinner, benzine or detergent, the printing may DOCOMO assumes no responsibility for the loss disappear or color may fade. of any of your data. ■Keep the connector contacts clean with a dry, ■Remove the FOMA terminal from the PC when soft cloth. transporting. Dirty contacts can result in intermittent connections. Malfunction or damage may result. ■Do not place the equipment near air conditioner ■It is normal for the FOMA terminal to become outlets. warm during use. You can continue to use it even Condensation may form due to rapid changes in when it is warm. temperature, and this may corrode internal parts and cause malfunction. Contents/Precautions...
Page 71
■Take care not to drop the FOMA terminal when ■Visit docomo Shop to return the FOMA card for removing the FOMA terminal from the carrying the environmental purpose. case. ■Avoid extreme temperature. ■When it is not in use, keep the FOMA terminal in ■Do not scratch, touch carelessly or short circuit its carrying case to keep the connector contacts the IC portion. clean. Data loss or malfunction may result. Dirty contacts may result in intermittent ■Do not drop or give shock to the FOMA card . connections. Malfunction may result. ■When putting the FOMA terminal in carrying case, ■Do not bend or put heavy things on the FOMA card. keep it away from wet or high temperature place. Malfunction may result. Pay attention not to put excessive force on the ■Do not insert UIM into the FOMA terminal with FOMA terminal. labels or stickers attached on. Transformation, tarnish, color staining may result. CAUTION FOMA Card ■Do not use the modified FOMA terminal. Using ■Do not put excessive force on the FOMA card modified FOMA terminal result in violating the law when inserting or removing it into the FOMA of Electromagnetic Compatibility. terminal. FOMA terminal has been complied with technical ■It is normal for the FOMA card to become warm standard of wireless equipment stipulated by law during use. You can continue to use it even when of Electromagnetic Compatibility. As for the proof, it is warm. the technical standard compliance mark, is ...
Page 72
Basic package ■ L-05A Terminal (With Rear Cover L13, Warranty) ■ L-05A CD-ROM • L-05A Connection Software (For Windows/Macintosh) • DOCOMO Connection Manager (For Windows/Macintosh) • L-05A INSTRUCTION MANUAL(PDF) ■ L-05A INSTRUCTION MANUAL〜Connection Guide〜 ※ Software specifications are subject to change without prior notice. ■ USB Extension Cable (Sample) Use when "USB Extension Cable" is written in this manual. ■ Carrying Case (Sample) ■ Mounting folder (Sample) Use when "A mounting Folder" is written in this manual. Contents/Precautions...
Page 73
Before Using the FOMA Terminal Names of Parts and Functions・・・・・・・・・・・・・・・・・・・ Using a FOMA Card・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ Available Communications ・・・・・・・・・・・・・・・・・・・・・・・ Connecting FOMA Terminal to a PC ・・・・・・・・・・・・・...
Page 74
Names of Parts and Functions Examples of USB Connector→P78 Ex. 1: ※ Pull out from FOMA terminal and turn Connection used to contact to a PC. maximumly 180 degrees before using. (90 degrees + 90 degrees) Antenna Part However, Damage may result from turning The antenna is inside the FOMA terminal. exceedingly 180 degrees. PWR Lamp→P73 Indicates the power supply conditions. IDLE/BUSY Lamp→P73 Ex. 2: Indicates the FOMA terminal status. ※ The tip part of USB connector can be turned maximumly 180 degrees. (90 degrees+90 degrees) However, it is one-way turn. Damage may result from turning to the opposite direction or turning exceedingly 180 degrees. Before Using the FOMA Terminal...
Page 75
Mode Indication Lamp Using a FOMA Card The FOMA card is an IC card that stores personal information such as your phone number. Without a FOMA card installed in the FOMA terminal, you cannot use data communication. For detailed information, refer to FOMA Card Manual. Inserting/Removing Inserting ※ Operation indicating lamp Inserting FOMA card with two hands. aPower bMode FOMA Terminal Status Indication Indication While pushing the cover in the direction of , Lamp Lamp slide the rear cover in the direction of . Lift When powered on the cover as shown by Waiting to connect to the FOMA Green Green network Attempting to Blue Green Packet communicate (Flash) communication Communicating Green Blue Rear Cover Yellow While receiving Green...
Page 76
Insert FOMA card into slot at the direction of Removing arrow with the IC chip side down Remove FOMA card with two hands. IC is faced While pushing the cover in the direction of , slide the rear cover in the direction of . Lift the cover as shown by FOMA card FOMA card slot Notch Rear Cover Fit the rear cover to the ditch of FOMA terminal at approximately 3mm from the top tip of the FOMA terminal. While pressing along Slide FOMA card in the direction of arrow and direction a, slide the rear cover along remove it from the FOMA Card slot. direction b till hear rear cover clicked. FOMA card Approx.3mm Before Using the FOMA Terminal...
Page 77
Approx.3mm entered. Use L-05A before verifying the PIN1 code, or set ("L-05A INSTRUCTION MANUAL (PDF)" P63)not to verify the PIN1 code in advance. Note ■ Changing the PIN1 Code You can change the PIN1 code to any number. To • Make sure not lose the removed FOMA card. prevent any unauthorized use by third parties, change it • Make sure to check the direction of FOMA card. to your own number. If you improperly enter the PIN1 code 3 times in a row, further entry is locked automatically (PIN lock), so be sure to keep a separate note of the numbers you set. • Entering PIN1 Code/ Changing PIN1 code→"L-05A • Be careful not to scratch FOMA card's IC parts. INSTRUCTION MANUAL (PDF)" P63 • Inserting FOMA card in the reverse direction may cause ■ PIN Unblocking Code malfunction. The PIN Unblocking Code is the number used to unblock • Inserting and removing FOMA card with an excessive force the PIN1 code. You are notified of your PIN Unblocking may cause damage to your FOMA card. Code when you purchase your FOMA terminal. Entering • Do not remove FOMA card while FOMA terminal is inserted the Unblocking Code (8-digit) unblocks the PIN lock. to a PC, it may causes damage to your FOMA card. If you improperly enter the Unblocking Code 10 times in a row, the FOMA card locks automatically, so be sure to ...
Page 78
Start up L-05A Connection Software The PIN1 code Verification screen appears FOMA Card Types Please be aware that the FOMA card (Blue) has different functions from the FOMA card (Green/White) as follows: Enter PIN1 Code FOMA card FOMA card Incorrect entry 3 times in a row Function (Blue) (Green/White) The number of digits of a Up to 20 digits Up to 26 digits phone number that can be This terminal allows Enter Unblocking PIN Code up to 20 digits. saved to the FOMA card Incorrect entry 10 times in a row Phonebook WORLD WING Not available Available You can set a new WORLD WING Contact a docomo Shop PIN1 code WORLD WING is DOCOMO's FOMA international roaming service that provides telephone and other types of mobile communications. It allows the subscriber to use the same phone number overseas as in Japan by inserting a FOMA card(green/white) into a FOMA terminal or a mobile phone designed for overseas use. • If you subscribed to the FOMA service after September 1, 2005, a separate subscription is not required. However, if you unsubscribed to the FOMA service subscription or canceled the service, a separate subscription is required.
Page 79
• Despite the plan you subscribe to, data communication from overseas will be uniformly charged based on Fees for this communication method are based on the measuring data. amount of exchanged data. You can perform data • FOMA terminal does not support 64K data communication at a maximum of 7.2Mbps for receiving and communication. 5.7Mbps for transmitting by using a connection that allows • This FOMA terminal does not support Remote Wakeup. FOMA communication such as "mopera U", one of • This FOMA terminal does not support FAX communication. DOCOMO's Internet connection services. ※ Communication speed is theoretical values when sending and receiving data which does not show the actual ones. The actual communication speed depends on communication environment and network congestion. • If you subscribe to Flat-rate data plan, connection will not be available even if you make an APN of Measured data plan when setting APN restriction. To cancel the APN restriction in advance is required. • Sending and receiving data become 384kbps in FOMA area out of FOMA HIGH-SPEED area. • The communication speed varies depending on the access point and radio wave status. • The communication speed varies depending on the overseas carrier or network when using overseas. • Use the "DOCOMO Connection Manager" in the CD-ROM to check the approximate number of transmission bytes and charges under the communication. Before Using the FOMA Terminal...
Page 80
Usage Notes Connecting FOMA Terminal to a PC ■ Internet service provider fees When connecting FOMA terminal with computer for the Fees to an Internet service provider may be required to first time, it is required to install L-05A connection connect to the Internet. These fees are added to the software (including a driver). For installing L-05A FOMA service fees and are paid to your Internet service connection software, refer to the followings. provider directly. For details on connection fees, contact • For Windows: "Preparation for using L-05A" (P87) your Internet service provider. You can subscribe to such as "mopera U", one of • For Macintosh: "Preparation for using L-05A" (P93) DOCOMO's Internet connection services. Charge for subscribing "mopera U" is required. For service and connection/settings of "mopera", visit the Inserting "mopera" website. http://www.mopera.net/mopera/index.html (Japanese Turn on a PC only) Connecting the FOMA terminal with a PC ■ User authentication to access networks Depending on the access point, user authentication (ID ■ When using a mounting folder and a USB extension and password) may be required to connect. If required, cable enter the ID and password from the dial-up network. The • Use a mounting folder and a USB extension cable to fix ID and password will be provided by the network on the top of a PC administrator of your Internet service provider or the ...
Page 81
bHold the connector part of USB extension cable and dHold the connector part of USB cable and insert into PC insert into the USB connector near the FOMA terminal USB port along arrow direction along arrow direction ※ Make sure to insert in USB connector deeply. USB connector USB port USB extension cable ■ When connecting with a PC directly • Insert the FOMA terminal into a PC USB port and use it USB extension directly. cable • The USB connector of FOMA terminal is able to turn 90 cPut the FOMA terminal between the mounting folder degrees complying to directions of USB port and fix on the top of the PC aPull out the projection part of USB connector 90 degrees by fingertip Mounting folder Projection part USB connector Before Using the FOMA Terminal...
Page 82
• It is available to use without turning USB connector 90 USB connector mark faced up. degrees as the above-mentioned procedure b. • USB connector ※ Available to turn 90 degrees for second time USB port (maximum 180 degrees). However, damage may • • ※ Refrain from turning the FOMA terminal after inserting result from excessive force when turning exceedingly USB connector into PC USB port. 180 degrees. Malfunction or damage may result when subject the FOMA terminal to severe shocks due to carelessness. cInsert the USB connector of FOMA terminal into a PC USB port Start communication connecting • Using "L-05A connection software" →"L-05A INSTRUCTION MANUAL (PDF)" P43 • Using "DOCOMO connection manager" →"L-05A INSTRUCTION MANUAL (PDF)" P69 • Configuring manually (OS Standard) →"L-05A INSTRUCTION MANUAL (PDF)" P79 Note USB connector USB port Power Indication Lamp Mode Indication Lamp • Confirm whether power indication lamp and mode indication lamp change to green. Before Using the FOMA Terminal...
Page 83
Removing folder from the FOMA terminal End data communication • If the L-05A connection software/DOCOMO connection manager is already running, exit the L-05A connection software/DOCOMO connection manager. Verify that data connection is disconnected. Mounting Remove the FOMA terminal folder ■ When using a mounting folder and a USB extension cable aHold the connector part of a USB extension cable and pull out the FOMA terminal from PC USB port along arrow direction cHold the connector part of the USB extension cable and pull out from the USB connector near the FOMA terminal along arrow direction USB connector USB port USB extension cable USB extension cable Before Using the FOMA Terminal...
Page 84
dPack the USB connector into the FOMA terminal bTurn the tip part of the USB connector 90 degrees as shown in the illustration Projection USB part connector connector cPack the USB connector into FOMA terminal ※ Make sure the projection part is in front before packing. ■ When connecting to a PC directly Projection part aHold the USB connector part of FOMA terminal. Pull out the FOMA terminal straightly from PC USB port USB connector ※ Make sure the projection part is in front before packing. Caution USB connector • If you force to remove FOMA terminal and pull out the USB USB port extension cable, this may result malfunction. • Removing FOMA terminal from USB connector during data communication may suspend data communication and result malfunction or data losses. Before Using the FOMA Terminal...
Page 85
Setting up Setting up ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ Windows Version ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ Macintosh Version ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・...
Page 86
Setting up ■ Data communication with L-05A "Communication configuration file (Driver)" and "L-05A connection software" are required to install for a PC to recognize the FOMA terminal. "Communication configuration file (Driver)" will be installed along with "L-05A connection software". Although data communication is available with only L-05A connection software, if necessary using it after installing DOCOMO connection manager in addition is also available. Data communication is also available based on configuring manually after installing L-05A connection software. ■ Installation of L-05A connection software Since L-05A has zero installation, when connecting the FOMA terminal to a PC for the first time, "L-05A connection software" installation screen appears automatically. "Zero installation" is supported by the PC with Windows OS in it. If zero installation works improperly, install L-05A connection software with the included CD-ROM. In addition, although Macintosh does not support the zero installation feature, installation continues through the CD- ROM icon appears when connecting the FOMA terminal to a PC. The procedure of setting up is described on the next page. Setting up...
Page 87
Confirmation after Setup ・ Windows Version P90/・ Macintosh Version P96 Configuring Using L-05A Using DOCOMO manually(Only connection connection manager Windows) software Installing DOCOMO connection manager Communication configuring manually Operation configurations of L-05A ・ Windows Version "L-05A INSTRUCTION MANUAL connection software "L-05A "L-05A INSTRUCTION MANUAL (PDF)" P71 INSTRUCTION MANUAL (PDF)" P60 ・ Macintosh Version (PDF)" P80 "L-05A INSTRUCTION MANUAL (PDF)" P75 Operation configuration/communication Communication connection with L-05A Communication configuring manually connection connection software "L-05A with OS function "L-05A with DOCOMO connection manager INSTRUCTION MANUAL (PDF)" P44 INSTRUCTION MANUAL (PDF)" P99 "DOCOMO connection manager manual"...
Page 88
※1 DOCOMO does not guarantee the operation under the supported OS of the OS is changed through update. Operating Environments ※2 Required memory or available hard disk space may vary depending on the system environment of a PC. Using this FOMA terminal under the following operational ※3 Only Mac with CPU made by Intel Corporation is available. environments. For latest information of operation environment, visit Item Requirement DOCOMO's "international website" PC Main • Available CD-ROM drive to use from PC/AT and Unit Mac compatible. Note • USB port (Comply with Universal Serial Bus Specification Rev1.1/2.0) • The software may not work depending on the operating • DOCOMO is not responsible for any system environment. DOCOMO does not guarantee any incompatibility of the operation performed operation other than the environment operation described through the USB Hub (including USB port on the left side. available from the monitor, keyboard, etc.) • Display resolution of 800×600 pixels, High Color (65.536) or higher is recommended. ※ Windows 2000 SP4 or later (Japanese versions) Windows XP SP2 or later (Japanese versions) Windows Vista SP1 or later (Japanese versions)
Page 89
■ For Windows Vista first time. Turn on PC and activate OS Note Connect the FOMA terminal with a PC • When installing, insert FOMA terminal into USB port after OS is activated. The setup screen of L-05A connection software is • Take out the CD-ROM from CD driver when zero installation automatically displayed by zero installation. starts. "自動再生" screen will be displayed depending on setting. If • Do not remove the FOMA terminal while installing. the screen is displayed, check "ソフトウェアとゲームに対しては • Installation may take several minutes depending on the PC 常に次の動作を行う" and select "Launcher.exeの実行" you use. • Do not install or uninstall during data communication. • End all the applications before installing. Also end programs on Windows including virus check software. • When installing, make sure to install from the account with PC supervisor privileges. An error will occur during installation if you install from the account without these privileges. • For details on setting up PC supervisor privileges, contact your computer manufacturer or Microsoft Corporation. ※ When the Setting up screen of L-05A connection software is not automatically displayed, install with the included CD-ROM (P89) Setting up...
Page 90
Click "許可(Allow)" on "ユーザーアカウント制御 Click "同意する (I Agree)" (User account control)" screen Installation starts. ■ For Windows XP/2000 • Because "ユーザーアカウント制御(User account control)" screen is not displayed, follow the next step Click "次へ(Next)" Click "完了(Finish)" Installation of L-05A communication configuration file (Driver) continues. Setting up...
Page 91
■ For Windows XP Click "スタート(Start)" "すべてのプログラム • On the lower right side of task tray, "新しいハードウェア (All programs)" "アクセサリ が見つかりました。 (A new hardware has been found.)" (Accessory)" Click message is displayed, and the FOMA terminal is recognized automatically. "ファイル名を指定して実行(Specify a file name and run)" ■ For Windows XP/2000 Click [スタート(Start)] "ファイル名を指定して実行 • If the FOMA terminal is recognized properly, "新しいハー (Specify a file)" ドウェアがインストールされ、使用準備ができました。(A new ¥ ¥ hardware has been installed and ready for use.)" Enter "<CD-ROMドライブ名>: Windows message is displayed. ¥ L-05A 接続ソフト StartCD.exe" in "名前 (Name)" Click "OK" "自動再生" screen will be displayed depending on setting. If the screen is displayed, check "ソフトウェアとゲームに対しては 常に次の動作を行う" and select "Launcher.exeの実行" Setting up...
Page 92
Perform the same operations as those after Confirming the Installed L-05A Configuration File step 3 or later on "Setting Zero Installation (Drivers) (Auto) (→P88)" Confirm whether L-05A Communication Configuration File ※ Connect FOMA terminal to PC after clicking "完了(Finish)" (Drivers) is set in a PC. in procedure 6. ■ For Windows Vista Click "スタート(Start)" "コントロールパネル Confirmation after Installation (Control panel)" "システムとメンテナンス (System and maintenance)" "デバイス マネー Confirming L-05A Connection Software ジャ(Device manager)" "続行(Continue)" Double click L-05A connection software icon ■ For Windows XP When the following screen is displayed, the confirmation of Click "スタート(Start)" "コントロールパネル(Control installation finishes. panel)" "パフォーマンスとメンテナンス(Performance and maintenance)" "システム(System)" "デバイス マ ネージャ(Device manager)" of "ハードウェア(Hardware)" ■ For Windows 2000 Click "スタート(Start)" "設定(Settings)" "コントロール...
Page 93
Click each device display to confirm the driver Note name installed • If FOMA terminal is not recognized through the PC's • Confirm whether the driver name is displayed below "ポート USB port, try other available USB port. FOMA terminal (COM とLPT)(Port (COM and LPT))", "モデム(Modem)" may not be recognized properly with some USB port of • When communicating data with L-05A connection software, application operation of L-05A connection software is required. →"L-05A INSTRUCTION MANUAL (PDF)" P60 • When communicating data with DOCOMO connection manager without L-05A connection software, installation of DOCOMO connection manager is required.→"L-05A INSTRUCTION MANUAL (PDF)" P71 • When communicating data with neither L-05A connection software nor DOCOMO connection manager, configure it manually.→"L-05A INSTRUCTION MANUAL (PDF)" P80 • COM port number differs depending on user and PC. Device name Driver name Port FOMA L05A USB Serial1 Device (COM and LPT) FOMA L05A USB Serial2 Device Modem FOMA L05A Setting up...
Page 94
Click "許可(Allow)" on "ユーザーアカウント制御 (User account control)" screen Uninstalling L-05A Connection Software If "キャンセル(Cancel)" is clicked, uninstallation will be stopped. (including a driver) ■ For Windows XP/2000 • Since "ユーザーアカウント制御 (User account control)" • Before uninstalling, remove the FOMA terminal from the PC. screen is not displayed, follow the next procedure. • When uninstalling, make sure to install from the account with PC supervisor privileges. Click "アンインストール (Uninstall)" • Make sure to save important data in FOMA card. Uninstallation will results in data loss when Phonebook or SMS data is saved in PC. ■ For Windows Vista "スタート(Start)" "すべてのプログラム (All programs)" "L-05A接続ソフト (L-05A connection software)" Click "Uninstall" ■ For Windows XP • "スタート (Start)" "すべてのプログラム (All programs)" "L-05A 接続ソフト(L-05A connection software)" Click "Uninstall" ■...
Page 95
Double click "L-05A 接続ソフト インストーラー .mpkg (L-05A connection software Macintosh Version installer.mpkg)" The L-05A connection software only need to be installed when you connect the FOMA terminal to your Mac for the first time. Note • When installing, insert FOMA terminal into USB port after OS is activated. • Take out the CD-ROM from CD driver when installation via FOMA terminal starts. • Do not remove the FOMA terminal while installing. • End all the applications before installing. Also end programs on Macintosh including virus check software. • When installing, make sure to install from the account with Click "続ける (Continue)" PC supervisor privileges. Preparation for Using L-05A Setting by FOMA Terminal Turn on Mac and activate OS Connect the FOMA terminal with a Mac CD-ROM icon is displayed on the desktop. Double click the CD-ROM icon Setting up...
Page 96
Click "続ける (Continue)" Click "インストール (Install)" Confirm "使用許諾契約 (The license Enter administrator password Click "OK" agreement)". If agree with the content, click "同意する (I Agree)" Setting up...
Page 97
Click "インストールを続ける(Continue Setting by CD-ROM installing)" Start Mac Insert the CD-ROM into Mac CD-ROM icon on desktop appears. Double click CD-ROM icon "Mac" "L-05A connection software" For subsequent steps, operate the same procedures as those after procedure 4 in "Setting by FOMA terminal)" (→P93) ※ Connect FOMA terminal to PC after restarting Mac in procedure 11. Click "再起動(Restart)" Mac restarts. Installation finishes. Setting up...
Page 98
Note Confirmation after Installation • When communicating data with L-05A connection software, setting application operations of L-05A Confirming L-05A Connection Software connection software is required.→"L-05A INSTRUCTION MANUAL (PDF)" P60 Launch "Finder" "アプリケーション(Application)" • When communicating data with DOCOMO connection manager without L-05A connection software, installation "L-05A 接続ソフト.app (L-05A connection of DOCOMO connection manager is required.→"L-05A software.app)" INSTRUCTION MANUAL (PDF)" P71 When the following screen is displayed, the confirmation of installation finishes. Setting up...
Page 99
Double click "L-05A接続ソフト (L-05A connection software)" Uninstalling L-05A Connection Software (including a driver) • Before uninstalling, remove the FOMA terminal from the Mac. • When uninstalling, make sure to install from the account with PC supervisor privileges. • Make sure to save important data in FOMA card. Uninstallation will results in data loss when Phonebook or SMS data is saved in PC. Insert the included CD-ROM into a Mac CD-ROM icon is displayed on the desktop. Double click the CD-ROM icon Double click "アンインストーラ.app Double click "Mac" (Uninstaller.app)" Setting up...
Page 100
Click "アンインストール(Uninstall)" Enter administrator password Click "OK" Confirm whether the FOMA terminal is connected to USB port before restarting Click "再起動(Restart)" Mac restarts. Uninstallation finishes. Setting up...
Page 101
Appendix/Troubleshooting Troubleshooting ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 100 Error Messages・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 102 Warranty and After-Sales Service ・・・・・・・・・・・・・・・ 104 Updating software ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 105 Main specifications ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 106 Export Administration Regulations ・・・・・・・・・・・・・・ 107 Intellectual Property Rights ・・・・・・・・・・・・・・・・・・・・・ 109 Index ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 110...
Page 102
"Repairs" at the last page of the manual if the symptom is ■ Communication problems not improved after confirming the check box. ■ The FOMA terminal is not recognized Symptom Check Communications Verify that signals are received in the Symptom Check are not possible service area. FOMA terminal Reinsert the FOMA terminal all the way into In the setting of Send Caller ID does not is not the USB port securely. conform to the provider's instructions, recognized Verify the L-05A Communication communication may not be performed. Configuration Files (Drivers) for the FOMA →"L-05A INSTRUCTION MANUAL (PDF)" terminal functioning properly.→P87, P93 P67, P80 Communication may fail and the FOMA Check if you set the FOMA Card Setting to terminal cannot be properly recognized and "PIN1 unblocking". →"L-05A INSTRUCTION functioned, if the PC is started up or restarted MANUAL (PDF)" P63 with the FOMA terminal FOMA terminal left If set to (PIN1 Lock), launch the L-05A inserted in it. In this case, remove and reinsert connection software, then change FOMA the FOMA terminal. If communication fails card setting to "PIN1 unblocking". →"L-05A even after the FOMA terminal is inserted ...
Page 103
[ERROR] Verify that you entered a correct AT The terminal Verify that the FOMA CARD is properly appears when a command. stopped working inserted to FOMA terminal.→P73 command is suddenly Check the properties of the terminal Your PC operating environments may have entered software to see whether a device other than changed because a new peripheral or the FOMA terminal is selected. software was installed. Make a confirmation with manufacturer or maker of accessory or [OK] does not Check the L-05A Communication software. appear after an Configuration Files (Drivers) have been AT command is installed and functioned properly. The FOMA Please confirm the followings. entered terminal is not • Whether the PC or OS you are using is in Verify that the commands start with "AT" or detected if it is the latest condition? "at". inserted into a (If required, apply revision program of OS or USB port while a maker.) installing the ...
Page 104
Error Messages Error Messages Description 圏外 You are out of service area or available network. サービス地域ではありません。ネットワークを You may be out of service area or available network, or network error. Please do network 再検索しますか? setting again. 端末の認証に失敗しました。顧客センターまた Communication may fail and the FOMA terminal cannot be properly recognized if the PC は代理店にお問い合わせください。 is started up or restarted with the FOMA terminal left inserted in it. In this case, remove and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is inserted again, remove it once, restart the PC, then insert the FOMA terminal into the PC again. Contact docomo Shop if the same problems persist. データ通信中には設定できません。終了後に設 You cannot customize setting during data communication. Try again after closing data 定してください。 communication. 変更するPIN1コードと確認用のPIN1コード Two of new PIN1 are not identical each other. New PIN1 you want to change is not が異なります。 matched to the PIN1 you entered for verification purpose. Enter correct PIN1. FOMAカードが挿入されているか確認してくだ Make sure to insert FOMA card into FOMA terminal before inserting to a PC. さい。 FOMA端末が取り外されました。 Do not remove FOMA card while using FOMA terminal. FOMA端末が取り付けられていません。 Verify the FOMA terminal is properly inserted into a PC. Verify that the FOMA terminal is properly recognized by the PC. PIN1コードを3回間違えたため使用できなく An incorrect PIN1 was improperly entered 3 times in a row. Available functions will be なりました。 (PIN1 blocked)PIN1コードが limited. Enter PIN unblocking code to unlock. ロックされています。 PIN1コードが違います。残り(○/3)回入力 An incorrect PIN1 code has been entered. Enter the correct PIN1 code again.
Page 105
Error Messages Description PIN1コードの変更はPINロックが設定されて To change the PIN1, PIN must be locked. Switch PIN unblocking to PIN blocking. いるときに可能です。 PIN1ロック解除コードが違います。残り(○/ An incorrect PIN1 was improperly entered 10 times in a row. Available functions will be 10)回入力可能です。再入力してください。 limited. Please enter the contact unblocking PIN1 code. SMS送信に失敗しました。 You may be out of service or available network.You may encounter problems due to the network error. PIN1ロック解除コードがブロックされている You are no longer able to use FOMA card that PIN unblocking code has been improperly ためFOMAカードを使用できません。顧客セン entered10 times in a row. Please contact docomo Shop. ターにお問い合わせください。 FOMA端末の初期化に失敗しました。FOMA端 Communication may fail and the FOMA terminal cannot be properly recognized, if the PC 末をリセットしてください。 is started up or restarted with the FOMA terminal left inserted in it. In this case, remove and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is inserted again, remove it once, restart the PC, then insert the FOMA terminal into the PC again. Appendix/Troubleshooting...
Page 106
• The subscriber is charged even during the warranty period • This product and all accessories are subject to change, in part for the repair of failures caused by the use of devices or or whole, for the sake of improvement without prior notice. consumable items that are not DOCOMO specified. • You will be charged if damage is found on the connector or etc after purchasing product. After-Sales Service ■ Repairs may not be possible in the following cases • When DOCOMO Repairs judges that the FOMA terminal is exposed to water. (Ex: the sticker is reacted to If Problems Occur water) • Before requesting service, read the "Troubleshooting" • Repair is not possible when corrosion due exposure to section in this manual. If the problem still persists, moisture, condensation or perspiration is detected in a contact one of the numbers listed in "Repairs" on the back moisture seal reaction or test, or if any of the internal of this manual. boards are damaged or deformed. ※ Since these conditions are outside the scope of the warranty, any repairs, if at all possible, will be charged. ■ After expiration of the warranty All repairs that are requested are charged.
Page 107
■ Replacement parts Basically, replacement parts (parts required to maintain product function) will be kept in stock for at least 4 years Updating software after termination of production. Please note that the product may not be repaired even during this period, Download the modification file of FOMA terminal from depending on the malfunctioning parts due to a shortage download site on the Internet and then update the of those parts. Depending on the nature of the required software. If software update is necessary, you will be repairs, it may still be possible to repair your terminal informed at the DOCOMO website with "お知らせ even after this period. Contact "Repairs" listed on the (Information)". back of this manual. Pay attention Note • Do not modify the FOMA terminal, the FOMA card or its • Do not unplug the FOMA terminal with the computer during accessories. software update. - Fire, injury or damage may result. • Software update (downloading and rewriting) may take a - If the FOMA terminal is modified (part replacement, while. modification, painting, etc.), it will be repaired only after the • If software update fails, all operations become unavailable. modified parts have been restored to the condition at the In this case, bring your FOMA terminal to a DOCOMO time of purchase. However, repair may be refused depending service center. on the nature of modification.
Page 108
※ Depending on the usage, power consumption fluctuates. or later) ■ Form factor Mac OS X 10.4.11 Japanese version USB connection type Mac OS X 10.5.6 Japanese version ■ Dimensions ■ Communication Speed Height: approx. 80mm Packet Communication: Width: approx. 32mm Maximum receiving: 7.2Mbps(Best effort) Depth: approx. 13.0mm Maximum sending: 5.7Mbps(Best effort) ■ Weight ※ Communication speed is theoretical values when sending Approx. 37g and receiving data which does not show the actual ones. The actual communication speed depends on communication environment and network congestion. ※ For details of areas supporting a maximum of 5.7Mbps for sending, view DOCOMO website. ※ Sending and receiving data may become 384kbps even in the FOMA HIGH-SPEED area. ※ Sending and receiving data become 384kbps in FOMA area out of FOMA HIGH-SPEED area. ■ Operating environment Temperature:5℃〜35℃ Humidity:45%〜85% Appendix/Troubleshooting...
Page 109
FCC Regulations Export Administration Regulations Statement Japan Export Control Regulations ("Foreign Exchange and This equipment has been tested and found to comply with Foreign Trade Law" and relevant laws and regulations) and the limits for a class B digital device, pursuant to Part 15 U.S. Reexport Regulations (Export Administration of the FCC Rules. These limits are designed to provide Regulations: EAR) apply to this product and its reasonable protection against harmful interference in a accessories. If you export or re-export this product or its residential installation. This equipment generates uses and accessories, please follow the necessary procedures at can radiate radio frequency energy and, if not installed and your own risk and expense. For details on the procedures, used in accordance with the instructions, may cause contact the Ministry of Economy, Trade and Industry or the harmful interference to radio communications. However, U.S. Department of Commerce. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be European Union Directives Conformance determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or Statement more of the following measures: Hereby, LG Electronics, Inc. declares that this • Reorient or relocate the receiving antenna. product is in compliance with: • Increase the separation between the equipment and receiver. •The essential requirements and other relevant • Connect the equipment into an outlet on a circuit different from provisions of Directive 1999/5/EC that to which the receiver is connected. •All other relevant EU Directives •...
Page 110
Consumer Information on SAR (Specific Absorption Class B Compliance Rate) This device and its accessories comply with part15 of FCC rules. THIS DEVICE MEETS THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Operation is subject to the following two conditions: Your wireless device is a radio transmitter and receiver. It • This device & its accessories may not cause harmful is designed and manufactured not to exceed the emission interference. limits for exposure to radio frequency (RF) energy set by • This device & its accessories must accept any interference the Federal Communications 'Commission of the U.S. received, including interference that may cause undesired Government. These limits are part of comprehensive operation. guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on Body-worn Operation standards that were developed by independent scientific organizations through periodic and thorough evaluation of This device has been tested for typical body-worn scientific studies. operations with the distance of 0.19inches (0.5cm) from The standards include a substantial safety margin the user's body. designed to assure the safety of all persons, regardless of To comply with FCC RF exposure requirements, a minimum age and health. The exposure standard for wireless separation distance of 0.19inches (0.5cm) must be devices employs a unit of measurement known as the maintained from the user's body. Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. ※ Tests for SAR are conducted using standard operating positions specified by the FCC with the device ...
Page 111
Before a device is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the Trademarks limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and • "FOMA" "i-mode" "i-αppli" "mopera U" "mopera" "WORLD WING" locations (e.g., worn on the body) as required by the FCC and "FOMA" logo are trademarks or registered trademarks of for each model. NTT DOCOMO, INC. • Free Dial logo mark is a registered trademark of NTT The highest SAR value for this device when worn on the Communications Corporation. body is 1.3W/kg. ® ® ® • Microsoft , Windows , Windows Vista are US and other The FCC has granted an Equipment Authorization for this countries registered trademarks of Microsoft Corporation. device with all reported SAR levels evaluated as in ® • Windows Vista is the abbreviation of Microsoft Windows compliance with the FCC RF emission guidelines. SAR ® ® Vista Home Basic operating system、Microsoft Windows information on this device is on file with the FCC and can Vista ®...
Page 112
Index Available Communications....77 Install Removing FOMA terminal....81 L-05A Connection Software on Macintosh (including a driver) .. 93 L-05A Connection Software on Basic package........70 Setting up ..........84 Windows (including a driver)..87 Communication Speed ..... 106 Troubleshooting........100 Main specifications ......106 Configuring Network Mode Indication Lamp ......73 Packet Communication ....77 Connecting FOMA terminal Uninstall to a PC ..........78 L-05A Connection Software Names of Parts and Functions ..72 (including a driver)......
Page 115
ご契約内容の確認・変更、各種サービスのお申込、各種資料請求をオンライ You can register a confirmation/change of contracts, or request ン上で承っております。 information material at the DOCOMO online. パソコンから My docomo(http://www.mydocomo.com/)⇒ 各種お From a PC My docomo (http://www.mydocomo.com/) ⇒ 各種お申 申込・お手続き 込・お手続き (Subscriptions/Procedures) ※ パソコンからご利用になる場合、 「docomo ID /パスワード」 が必要とな ※ "docomo ID/Password" is required if you access the site from a PC. ります。 ※ If you do not have or remember the "docomo ID/Password", contact ※ 「docomo ID /パスワード」をお持ちでない方・お忘れの方は、取扱説明書裏 the "docomo Information Center" listed on the back of this manual. 面の総合お問い合わせ先にご相談ください。 ※ Some contracts may not be available for using. ※ ご契約内容によってはご利用いただけない場合があります。 ※ You may not be able to use online service due to system ※ システムメンテナンスなどにより、ご利用になれない場合があります。 maintenance, etc. マナーもいっしょに携帯しましょう Don't forget your FOMA terminal… or your manners! When using the FOMA terminal, be considerate and do not FOMA 端末を使用する場合は、周囲の方の迷惑にならないように注 disturb people around you.
Need help?
Do you have a question about the L-05A and is the answer not in the manual?
Questions and answers