Table of Contents
Advertisement
E9015ED_EN.qx3
03.7.29
Video Channel Setting
Video channel setting will be necessary, if your System is con-
nected to the TV via the coaxial cable.
1 Insert a pre-recorded tape into the System.The System will turn
on and start playback automatically.If playback does not start,
press PLAY B .
2 Select and adjust your TV to channel 36.
• If the playback picture appears on the TV screen, continue
with step 8.
• If channel 36 is employed for broadcasting, or interference
lines appear on the picture, the RF converter must be set to
a different channel between CH22 and CH69. Continue with
step 3.
3 Press DISC/VCR MENU.
4 Press K/L to select INITIAL SET
UP.Then, press B.
5 Press K/L to select RF OUT.Then,
press B twice.
6 Press K/L to select a channel
which is not used for broadcasted
between channel 22 and channel 69
in your area, then press B.
• You can also see the selecting RF channel in the display.
7 Press DISPLAY/STATUS/EXIT to exit.
Set the TV channel to the RF OUT CHANNEL which was
selected on the System. A picture from the VCR will appear on
the TV screen. If a picture does not appear, repeat steps 3 to 7
using a different channel which is not used for broadcasting.
8 Press STOP C to stop the tape.
Note:
– You may also access the RF OUT CH menu by pressing
and holding DISC/VCR MENU for 3 seconds during
power off until the RF OUT CH menu appears.
Automatic Channel Setup
You can programme the tuner to scan only the channels that
you can receive in your area.
1 Turn on the TV and select the video out channel on your TV.
2 Press VCR, then DISC/VCR MENU.
3 Press K/L to select TUNER SET UP, then press B.
4 Press K/L to select AUTO TUN-
ING, then press B.
• The tuner scans and memorizes
all the active channels in your
area. After scanning, the tuner
stops on the lowest memorized
channel.
5 Press SKIP/P+ G / SKIP/P- H or
numerical key pads to scan through channels you have
received.
Manual Channel Preset
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select TUNER SET UP, then press B.
3 Press K/L to select MANUAL
TUNING, then press B.
4 Press K/L to select PROG., then
press B.
5 Press K/L or numerical key pads
to select your desired programme
number, then press B.
• You can select programme num-
ber 01-99.
6:32 PM
Page 9
SELECT K L CHOOSE B
RF OUT CH 36
SET=0-9
END=EXIT
PLEASE WAIT
START
FINISH
MANUAL TUNING
PROG.
P55
CHANNEL
055
DECODER
[OFF]
SKIP
[OFF]
SET=K L OR 0 – 9
END=EXIT
Setting Up your System
6 Press K/L to select CHANNEL, then press B.
7 Press K/L.The System tuner will begin to search up or down
automatically.When a channel is found, the System will stop
searching and the picture will appear on the TV Screen.
• You can select desired channel number by using numerical
key pads.You must refer to the channel plan and press three
digits to select the channel number. (To select channel 24,
first press "0" button then press "2" and "4").
• If this is the channel you want, press B.
• If you want to remove scrambled signals, press K/L to select
DECODER.Then, press B to select [ON].
8 Press DISPLAY/STATUS/EXIT to exit.
Notes:
– To confirm that a channel has been added, press the
G / SKIP/P- H
H buttons.
SKIP/P+ G
– You should select the satellite channels to be received by
the satellite receiver directly on the receiver itself.
Follow TV (Automatic TV channels sorting)
When the automatic channel search function is activated, the
TV channels are saved in a specific order.This may vary from
the order of TV channels on the TV.
This function changes the order of TV channels saved in the
System to match that of the TV.
Make sure that the System and the TV are connected by a
scart cable.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select TUNER SET
UP, then press B.
3 Press K/L to select 'FOLLOW TV'
, then press B.
4 'P:01' will appear in the System dis-
play.
I cannot switch my TV set to programme number '1'
* If you have connected additional devices to socket
AV2(DECODER), please disconnect these devices. Because of
other connected devices, the TV set could switch to the pro-
gramme number of the scart socket.
'NO TV SIGNAL' will appear in the TV screen.The
System is not receiving a video signal from the TV.
Check the plug on the scart cable.
Check your TV's operating instructions to see which scart socket
is used for video signals.
If this does not help, it's not possible to use this function. Please
read the section 'Sorting and Clearing TV channels manually'.
5 Select programme number '1' on the TV.
6 Confirm with B on the System remote control.The System
compares the TV channels on the TV and the System.
If the System finds the same TV channel as on the TV, then it
stores it at 'P01'.
7 Wait until the next number, e.g. 'P:02' appears in the display.
8 Select the next programme number on the TV, e.g. '2'.
9 Confirm with B.
10 Repeat steps 7 to 9 until you have assigned a programme num-
ber to all TV channels.
11 To end, press DISPLAY/STATUS/EXIT.
SELECT K L CHOOSE B
AUTO TUNING
MANUAL TUNING
FOLLOW TV
MOVE
END=EXIT
9
Hide quick links:
Advertisement
Table of Contents
