Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Staufenbiel VEGAS
Summary of Contents for Staufenbiel VEGAS
- Page 1 INSTRUCTIONS Art.No.: 0314073 / 0314073P...
-
Page 2: Specifications
Manual VEGAS Specifications: R/C Functions: • Span: 2000 mm • Aileron • Length: 1120 mm • Elevator • Wing area: 31,18 dm² • Rudder • flying weight: 1700 g • Motor • Airfoil: MH-43... -
Page 3: Safety Precautions And Warnings
Do not use with incompatible compo- nents or alter this product in any way outside of the instructions provided by Gustav Staufenbiel GmbH. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury. - Page 4 Manual VEGAS 1) THE WINGS Prepare the slot for the rudder horn. Sand the rudderhorn slightly and glue it with 5 min Epoxy. (ARF VERSION ONLY) Assembly the 2 x 50 cm servo extension cable for the aileron servos or by them from Staufenbiel.
- Page 5 VEGAS Manual (ARF VERSION ONLY) If you are an experienced modeller it is your decision to install an MPX connection in the wings and the fuselage. Second and as an easier option is to route the 15cm aileron extension cable in the wing.
- Page 6 Manual VEGAS Glue the servocover with doubleside tape. ..or with Tesa tape from the topside. (ARF-VERSION ONLY) If you are an experienced modeller its on your deci- sion to install an Multipex Multilock System in the fuselage and wing. Please follow the Multilock manual.
- Page 7 VEGAS Manual 2) THE FUSELAGE Glue the rudder hinges with 5 min Epoxy into the fuselage. Fix the rudder on the fuselage and glue it with 5 Min Epoxy. (ARF-VERSION ONLY) Assembly the servo extension cable for the elevatorservo or by an...
- Page 8 Manual VEGAS Enlarge the hole in the rudderhorn to 1,6mm..so the clevis fiths tight. Please check this. Install the rod in the middle of the clevis. Lay the rod on the fuse- lage and cut it as shown a bit behind where there rod will protrude the fuselage.
- Page 9 VEGAS Manual Install the Linkage conncector on the Servo- horn of the rudder. Install the rudder servo in the fuselage and set it with the radio or servo tester to neutral. Connect the rod to the servo connection. The rudder should set to neutral and the ser- vohorn perpendicular.
- Page 10 Manual VEGAS Enlarge the elevator rud- derhorn to 1.8mm and glue it as shown with 5 min Epoxy. (ARF-VERSION ONLY) Set the evelvator servo to neutral. Shrink the servo in heatshrunk tube as done before with the aileronservos and cut the openings.
- Page 11 VEGAS Manual Route the rod into the fuselage and connect the clevis to the servo- horn. Bend the rod to 90° aligned to the seating of the elevator. Cut the rod to 15mm lenght after the bend. Place the elevaor on the...
- Page 12 Manual VEGAS Install the propeller Fix the battery with velc- ro in the fuselage. Depending on its size glue some foam tape under the receiver. THE END!
-
Page 13: Center Of Gravity
VEGAS Manual C.G. (Center of gravity): The recommended Center of Gravity (C.G.) location for the VEGAS is 60-65 mm back from the lea- ding edge of the wing against the fuselage. Control throws: Flight mode Function Normal Brake Aileron Up: 15 mm,... -
Page 16: Declaration Of Conformity
Text: M.V. Pictures: M.V. Translation: C.H. STAUFENBIEL Gustav Staufenbiel GmbH, Hanskampring 9, 22885 Barsbüttel, Germany CEO: Klaus Breer, Jörg Schamuhn Tel.: +49 40-30061950, eMail: info@modellhobby.de, Webside: www.modellhobby.de Copyright © Gustav Staufenbiel GmbH, 2014...
Need help?
Do you have a question about the VEGAS and is the answer not in the manual?
Questions and answers