Advertisement

Available languages

Available languages

Quick Links

Texas A/S - Knullen 22 - DK-5260 Odense S - Denmark
Tel. +45 6395 5555 - www.texas.dk - post@texas.dk
DK
Betjeningsvejledning
GB
Instruction manual
Smart Combi 100
Version 16.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Smart Combi 100 and is the answer not in the manual?

Questions and answers

Summary of Contents for Texas Equipment Smart Combi 100

  • Page 1 Betjeningsvejledning Instruction manual Smart Combi 100 Texas A/S - Knullen 22 - DK-5260 Odense S - Denmark Version 16.1 Tel. +45 6395 5555 - www.texas.dk - post@texas.dk...
  • Page 2 Illustrationer / illustrations Fig. 1 Fig. 2 Fig. 3...
  • Page 3 Fig. 4 Fig. 5...
  • Page 4 DA Specifikationer, GB Specifications Produkt Product Smart Combi 100 Motor specifikationer Engine specification Motor type Engine type 230V Effekt Net power 900W Starter Starter e-starter Kobling Drive system Tilkobling Activation Kontakt/switch Trimmer Trimmer Arbejdsbredde trimmer Working width trimmer 36 cm Snørre type...
  • Page 5 Produkt Product Smart Combi 100 Emissionsdata Emissiondata Machine inkl. trimmer Machine incl. Trimmer Vibrationsniveau front håndtag Vibrationlevel front 2,720 m/s^2 Vibrationsniveau bagerste håndtag Vibrationlevel rear 2,785 m/s^2 Lpa lydtryksniveau Lpa soundpressure level 91,22 dB(A) Lwa lydeffektniveau Lwa soundeffect level 102.47 dB(A)
  • Page 6 Indholdsfortegnelse (Original brugsansvisning) DA Specifikationer ............................. 4 GB Specifications .............................. 4 Identifikation af symboler og sikkerhedsinstruktioner ..................6 Identifikation af dele ............................7 Montering ................................7 Brug af forskellige tilbehør ..........................7 Udskiftning af snøre ............................8 Anvendelse ................................ 8 Start / Stop .................................
  • Page 7 Identifikation af dele Se fig.1 og illustration: Motor Kædesav Hækkeklippe Trimmer (Justerbar 135°) Montering Monter håndtaget som vist i fig. 2. Sørg for, at maskinen er i balance og bolte er stramme. Monter på maskinen, fastgør. Se fig. 2. Montering af: Trimmer B.
  • Page 8 Udskiftning af snøre Fig. 4 1. Tryk ind i hver side på selve snørehuset (tryk til og hold inde). Låget kan nu tages af. 2. Afmonter selve rullen, ved at trække i den, Lad fjederen, blive på spolen. Fjern evt. rester af snøre. 3.
  • Page 9 Smøring af savkæde  Lad grensaven køre en 2-3 min i friløb.  Placer grensaven på et plant underlag  Afmonter låg  Påfyld beholderen på grensaven med kædeolie (fyld helt op). Alt efter forholdene bør kædeolie påfyldes for hver 30-45 min arbejdstid, men tjek jævnligt! Hvis grensaven kører uden olie, ødelægges kæden.
  • Page 10: Table Of Contents

    Table of Contents Identification of symbols and safety instructions ..................... 10 Identification of parts ............................11 Assembly ................................. 11 Attaching the: ..............................11 Use of attachements ............................11 Replacement the trimmer cord ........................12 Operation ................................. 12 Start / Stop............................... 12 Storage ................................
  • Page 11: Identification Of Parts

    Identification of parts See fig.1 illustration: Engine Chainsaw Hedgtrimmer Grass trimmer ( Adjustable 135°) Assembly Mount the handle as shown in Fig 2. Ensure that the machine is in balance and bolts are tighten. Attach the middle tube to the machine, fasten with butterfly knob. See fig 2. Attaching the: Trimmer B.
  • Page 12: Replacement The Trimmer Cord

    Replacement the trimmer cord Fig.4 1. Press on each side of the line compartment. The lid may now be removed. 2. Dismount the roll simply by pulling it. Leave the spring on the spool. Remove any bits of line. 3. Take 3-4 meters of new line (2,4 mm) and place it double in a loop- 4.
  • Page 13: Troubleshooting

    Depending on the conditions you should add chain oil for every 30-45 minutes of use, so check oil level often. If the pruner is used without chain oil, the chain will be damaged. Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION The line cannot be pulled 1.
  • Page 14: Ec Declaration Of Conformity

    Texas Andreas Petersen A/S Erklærer herved at materiel • Hereby certifies that the following Elektrisk Buskrydder • Electrical Brushcutter Smart Combi 100 Er fremstillet i overensstemmelse med følgende direktiver • Is in compliance with the specifications of the machine directive and subsequent modifications 2011/65/EC, 2004/108/EC, 2006/42/EC, 2000/14/EC Materiellet er udført i henhold til følgende standarder •...

Table of Contents