Table of Contents
Advertisement
kETTINGS
FOR
AN
EXTERNAL
DEVICE
pplied cables
used
in
this
connection
ai
PROG.
B
CA
audio cable
(L/R)
x
1
CA
video cable
x
1
?ase
purchase the
rest
of the
necessary cables
at
your
local store.
If
there
is
a
power
failure
or
this
unit
has
been unplugged
for
more
than 30 seconds,
the clock
setting
and
all
tim
neCt the external
device properly
to either L2
(front)
or
LI (rear)
input
jacks of
this
unit
by
using S-video or
RCA
programming
will
be
lost.
j
0
/
v jdeo
cables.
If
you
are
connecting
a
DVC
(digital
video camcorder), connect
it
to
L3
(front)
by
using
DV
cable.
If
a
disc
is
not
inserted,
g|
flashes
and
timer recording
cannot be performed.
In
some
cases,
jl§
will
appear
momentarily around
the
start
point
as
the
unit
attempts
to record.
Please
insert a
recordable
disc.
When
all
the timer recording
is
completed,
|§§
flashes.
To
play
back
or eject
the recorded
disc,
press
[1/6
©W/STANDBY]
first,
then
select
the recorded
title
and
press
[PLAY
Dr-],
or
[OPEN/CLOSE
to
remove
the
During timer recording
or
timer
standby
mode
(§|§ will
appear),
any
operations
on
the
unit
will
not
be
available. To
these operations
available,
press
[STOPS]
on
the
front
panel
to cancel
the timer recording
or
[1/6
OSWSTAMDBY;
release
timer
standby
mode
(@§
will
disappear).
To
cancel
the timer
standby
mode,
press
[1/6
ON/STANDBY].
When
the
starting
and
the
ending time
are
the same, the length
of the recording
will
be
set for
24
hours.
When
i
disc
becomes
full
during the
recording,
the
unit turns
itself
off.
When
the
programmed
starting
and ending
time
are
earlier
than the
current time, the
setting
will
not
be
accept)
and be
cleared
for
redoing.
If
the
starting
time
is
earlier
and
the
ending time
is
later
than the
current time, the recording
will
start
right
after
turn
the
power
off.
AUDIO OUT-
S-VIDEO
OUT
VIDEO
OUT
DV-OUT
AUDIO
OUT
VIDEO
OUT
S-VIDEO
OUT
externa! device
(camcorder,
VCR
etc.)
S-video
cable
RCA
audio
cable
RCA
video
cable
RCA
audio
cable
The
Priority
of
Overlapped
Settings
This unit
records the
programs
according
to
priority
if
the timer
programmings
are
overlapped.
The
timer
programming
set
previously has
priority.
A
timer recording of lower
priority
will
be
canceled
or
start
from
the middle.
Check
the
overlapped
timer
programmings and change
the
priority
if
necessary.
El
When
the
starting
time
is
the
same:
H
When
the
starting
time
and
the
ending time
A
program
set
previously
(PROG.
A)
has
priority.
for
each programs
are
different:
A program
that
has
earlier start
time has
priority.
-rrvB&
l
rear
of
this
unit
front of
this
unit
du use
L2 or
LI
connection,
make
sure to
select
the appropriate video input type
by
following the steps
in
TTINGS
FOR THE VIDEO
INPUT"
on page
1
9.
PROG.
A
PROG. B
PROG.
A
The
first
2
minutes
(at
the
longest)
will
be
cut
off.
The
first
2
minutes
(at
the
longest)
will
be
cut
off.
meeting
an
external
device of
monaural output
to
this unit,
use
AUDIO
L
jack
c
irst
select
the desired audio
from
the
external
device before
recording.
You
a:
>r
audio
right
during playback
of self-recording
discs.
H
When
the recording time
is
partially
overlapped:
PROG.
A
will
start after
PROG.
B
is
complete
to
be
recorded.
When
the recording time
is
entirely
overlapped:
PROG.A
will
not
be
recorded.
PROG.
PROG.
B
PROG.B
[The
first
2
minutes
(at
the
longest)
will
be
cut
off.
When
the
end
time
of
the
programming
currently
being recorded
and
the
start
til
Note
for
D
•
When
the
r
the
end
tin
- Quick Links:
- Formatting a Disc
Hide quick links:
Advertisement
Table of Contents
