Subscribe to Our Youtube Channel
Related Manuals for Porter-Cable PCC761
Summary of Contents for Porter-Cable PCC761
- Page 1 20v Max* 4-1/2 inch (115mm) Lithium Cut Off Tool / Grinder Instruction manual *Maximum initial battery pack voltage (measured without a workload) is 20 volts. CATALOG NUMBER The nominal voltage is 18. PCC761...
-
Page 2: Safety Guidelines - Definitions
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. -
Page 3: Safety Instructions For All Operations
connection of dust extraction and to another. Shorting the battery terminals collection facilities, ensure these are together may cause burns or a fire. connected and properly used. Use of d) Under abusive conditions, liquid may dust collection can reduce dust-related be ejected from the battery, avoid hazards. - Page 4 wire brush for loose or cracked q)Do not use Type 11 (flaring cup) wheels on this tool. Using inappropriate wires. If power tool or accessory accessories can result in injury. is dropped, inspect for damage or install an undamaged accessory. r) Always use side handle.
-
Page 5: Safety Warnings Specific For Grinding And Abrasive Cutting- Off Operations
movement at the point of snagging. susceptibility to twisting or binding of the wheel in the cut and the possibility d)Use special care when working of kickback or wheel breakage. corners, sharp edges etc. Avoid bouncing and snagging the b) Do not position your body in line accessory. -
Page 6: Additional Safety Information
wheel or brush with the guard. Wire WARNING: Do not operate this tool wheel or brush may expand in diameter for long periods of time. Vibration due to work and centrifugal forces. caused by the operating action of this c) Safety glasses: Safety Goggles or safety tool may cause permanent injury to glasses with side shields and a full face fingers, hands, and arms. -
Page 7: Important Safety Instructions For Battery Chargers
Burn hazard. To reduce the electrocution or fire. risk of injury, charge only designated Disconnect the charger from the outlet PORTER-CABLE batteries. Other types before attempting any cleaning. This will of batteries may burst causing personal reduce the risk of electric shock. Removing injury and damage. -
Page 8: Storage Recommendations
To facilitate the cooling of the battery pack after Charge the battery packs only in PORTER-CABLE chargers. use, avoid placing the charger or battery pack in a warm environment such as in a metal DO NOT splash or immerse in water or other liquids. - Page 10 1/4 inch wheels Threaded clamp nut Backing flange 1/8 inch wheels Threaded clamp nut Backing flange 4-1/2 inch (115mm) Grinding Wheels 4-1/2 inch (115mm) Sanding Flap Discs Type 27 guard Type 27 guard Type 27 guard Type 27 guard Unthreaded backing flange Hubbed sanding flap disc Unthreaded backing flange Type 27 hubbed wheel...
- Page 11 Return it to a service center or a collection site for PORTER-CABLE chargers are designed recycling. to charge PORTER-CABLE battery packs. HOT/COLD PACK DELAY When the charger detects a battery that is excessively hot or excessively cold, it automatically starts a Hot/Cold on the pack being charged.
-
Page 12: Trigger Switch
balances the individual cells in the battery ACCESSORIES pack to allow it to function at peak capacity. It is important to choose the correct Battery packs should be tuned up weekly or guards, backing pads and flanges to use whenever the battery no longer delivers the with grinder accessories. -
Page 13: Spindle Lock
so that the lugs on the guard (9) are off, the battery is removed, and the wheel aligned with the slots on the gear case has come to a complete stop. cover, and pull up on the guard. Do not engage the spindle lock while the FIGURE G tool is operating. - Page 14 threaded clamp nut is tightened, check the orientation of the threaded clamp nut. If a surface, allowing the tool to operate at thin wheel is installed with the pilot on the high speed. Sanding rate is greatest clamp nut against the wheel, it will spin when the tool operates at high speed.
-
Page 15: Environmental Safety
up and disposed of along with any 4. Move the tool constantly in a straight dust chips or other removal debris. line to prevent burning and swirling of They should be placed in sealed refuse work surface. Allowing the tool to rest receptacles and disposed of through on the work surface without moving, regular trash pick-up procedures. -
Page 16: Maintenance & Cleaning
the tool to rest on the work surface must be used for cutting wheels. without moving, or moving the tool in 1. Place the unthreaded backing flange a circular motion causes burning and on spindle with the raised section swirling marks on the work surface. (pilot) facing up. -
Page 17: Troubleshooting
never immerse any part of the tool into a liquid. LUBRICATION Porter Cable tools are properly lubricated at the factory and are ready for use. Tools should be lubricated regularly every year depending on usage. (Tools used on heavy duty jobs and tools exposed to heat may require more frequent lubrication.) This lubrication should be attempted only by trained power tool repairperson’s such as...
Need help?
Do you have a question about the PCC761 and is the answer not in the manual?
Questions and answers