Sony PXW-FS5 Software Update
Hide thumbs
Also See for PXW-FS5:
- Operating manual (172 pages) ,
- Firmware update (86 pages) ,
- Firmware update (72 pages)
Related Manuals for Sony PXW-FS5
Summary of Contents for Sony PXW-FS5
- Page 1 PXW-FS5/ PXW-FS5K System software update Windows 2016/02/26...
- Page 2 Preparing system software update Please prepare the following items in addition to your camera. System requirements for a computer 【 Windows 】 [Supported OS] Windos® 10 Windows® 8.1 Windows® 7 Windows Vista®*1 SP2 *1 Starter edition is not supported. [Other system requirements] - Hard disk space: 200MB or more - RAM: 512MB or more * Please close all other application software before updating the system software .
- Page 3 Other items Power source for the camera ・AC-UES1230(supplied) Note: The update can be performed only when using AC adaptor. Battery cannot use for this update. USB cable(supplied) Type A Male to Micro-B Male Cable...
-
Page 4: For Windows
PXW-FS5/ PXW-FS5K System software update Windows For Windows... - Page 5 Updating the system software (PXW-FS5 / PXW-FS5K) - When performing the system software update, please use the supplied AC adaptor. update doesn’t work in case using battery. -Do not remove the AC adaptor during the update; otherwise, the camera may become inoperable due to the sudden power shutdown.
- Page 6 2. Start up Firmware Updater ・ Close all currently running programs on your computer. ・ Double-click downloaded file to start up Firmware Updater...
- Page 7 3. Connect the camera to the computer 1. Camera power on by AC adapter. 2. Connect the camera to the computer with the supplied USB cable. If the computer cannot find the camera, the message “ Could not find the camera for this update.”...
- Page 8 4. Check if the update is required 1. When click the "Next" button on the Firmware Updater it will display like the below. Note: Never power off until finish the upgrading. 2. After confirming the current version on the screen, click [Next]. Firmware Updater Camera’s LCD screen Current version “Ver.1.10”...
- Page 9 5. Reset the camera The information is displayed as shown below, the reset of the camera is done.
- Page 10 6. Start the update After the reset work, will start the update. During the update (about 5 minutes), you will see the progress bar. Note: Never turn off the camera nor disconnect the USB cable while upgrading.
- Page 11 7. Complete the update When the update is completed, the “Finish the update” screen appears. Click [Finish] and disconnect the USB cable. Note: After the update is complete, please do the date and time setting cycle the power of the camera body.
- Page 12 8. Check the system software version Follow the instruction below to confirm the system software version is Ver.1.11. Select [Menu] [SYSTEM] [VERSION DISPLAY] on the camera. The system software version is displayed.
- Page 13 PXW-FS5/ PXW-FS5K System software update For Mac OS...
- Page 14 Updating the system software (PXW-FS5 / PXW-FS5K) - When performing the system software update, please use the supplied AC adaptor. update doesn’t work in case using battery. -Do not remove the AC adaptor during the update; otherwise, the camera may become inoperable due to the sudden power shutdown.
- Page 15 2. Start up Firmware Updater 1. Double-click the downloaded file [Update_PXWFS5V111.dmg]. Do not connect the camera yet at this point. 2. [Update_PXWFS5V111] icon appears on the Desktop. 3. Double-click the [FirmwareUpdater] icon. 4. To load a kernel extension, the message prompts you to allow the application to make changes.
- Page 16 5. Firmware Updater starts up.
- Page 17 3. Connect the camera to the computer 1. Camera power on by AC adapter. 2. Connect the camera to the computer with the supplied USB cable. If the computer cannot find the camera, the message “ Could not find the camera for this update.”...
- Page 18 4. Check if the update is required 1. When click the "Next" button on the Firmware Updater it will display like the below. Note: Never power off until finish the upgrading. 2. After confirming the current version on the screen, click [Next]. Current version “Ver.1.10”...
- Page 19 5. Reset the camera The information is displayed as shown below, the reset of the camera is done.
- Page 20 6. Start the update After the reset work, will start the update. During the update (about 5 minutes), you will see the progress bar. Note: Never turn off the camera nor disconnect the USB cable while upgrading.
- Page 21 7. Complete the update When the update is completed, the “Finish the update” screen appears. Click [Finish] and disconnect the USB cable. Note: After the update is complete, please do the date and time setting cycle the power of the camera body.
- Page 22 8. Check the system software version Follow the instruction below to confirm the system software version is Ver.1.11. Select [Menu] [SYSTEM] [VERSION DISPLAY] on the camera. The system software version is displayed.