Advertisement
Natural Gas & LPG
PI No. 0063 BN 3218
0087 BS 61 (imax W100 only)
Destination Countries: GB, IE
I n t r o d u c t i o n
The
is a wall mounted, room sealed, super efficient
condensing boiler featuring full sequence automatic spark
ignition and fan assisted combustion.
Due to the very high efficiency, condensate is produced from the
flue gases and this is drained to a suitable disposal point
through the plastic waste pipe at the bottom of the boiler. A
condensate 'plume' will also often be visible at the flue terminal.
S a f e t y
Current Gas Safety (Installation & Use)
Regulations or rules in force.
In your own interest, and that of safety, it is the law that this boiler
must be installed and maintained by a CORGI registered
installer or in IE a competent person, in accordance with the
above regulations.
The appliance should be serviced at least once a year by a
CORGI registered installer or in IE a competent person.
It is essential that the instructions in this booklet are strictly
followed, for safe and economical operation of the boiler.
Electricity Supply
The appliance must be earthed.
Supply 230 V - 50 Hz.
The fusing should be 3A (5A for W100).
This appliance is intended to be connected to the supply via a
double-pole switch, having a 3mm contact separation in both
poles, serving only the boiler and system controls. Alternatively, a
3-pin UNSWITCHED socket may be used.
All CORGI Registered Installers carry a CORGI ID card, and have a registration number. Both should be
recorded in your Log Book. You can check your installer by calling CORGI direct on 01256 372 300.
CAUTION. To avoid the possibility of injury during the installation, servicing or cleaning
of this appliance care should be taken when handling edges of sheet steel components.
2
Important Notes
This appliance must not be operated without
•
the casing correctly fitted and forming an adequate seal.
If the boiler is installed in a compartment then the
•
compartment MUST NOT be used for storage purposes.
Do not store objects around or on the boiler, and keep
•
access clear at all times.
Do not obstruct ventilation ducts, grilles or openings in the
•
boiler room, room space or compartment that the appliance
is installed in, or the passage of combustion and ventilation
to the boiler.
Do not turn off the boiler if it is to be left unattended in frosty
•
weather.
If it is known or suspected that a fault exists on the boiler
•
then it MUST NOT BE USED until the fault has been
corrected by a CORGI registered installer or in IE a
competent person.
Flammable materials must not be placed in close proximity
•
to the appliance. Materials giving off flammable vapours
must not be stored in the same room as the appliance.
This appliance is not intended for use by persons (including
•
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
•
play with the appliance.
In cases of repeated or continuous shutdown a CORGI
registered installer or in IE a competent person should be called
to investigate and rectify the condition causing this and carry out
an operational test after each intervention on the device. Only the
manufacturers original parts should be used for replacement.
Minimum Clearances
Clearances of 300mm (12") below, 50mm (2") at the sides and
450mm (17 3/4") at the front of the boiler casing must be
allowed for servicing.
To light the boiler
(Refer to Frame 1)
1. CHECK THAT THE ELECTRICITY SUPPLY TO THE BOILER
IS OFF.
2. Set the burner on/off switch (A) to off.
3. Switch on the electricity supply to the boiler and check that all
external controls, e.g. programmer, room thermostat, etc are
on. Allow the boiler to carry out a self check.
4. Set the burner on/off switch (A) to ON.
The boiler will commence the ignition sequence, supplying heat
to the system when required.
-
User's
Advertisement
