Table of Contents
Advertisement
Quick Links
1.0 Installation and Startup Guide
0
Install Environment
7
Where
The MT-600/8000 Series is designed for industrial. The temperature range of operating
Used
is from 32 to 113 °F (0 to 45 °C) , as majority of industrial environments. It may not
be suitable for using in certain outdoor applications. Please consult the factory for
advised usage in outdoor applications.
NEMA
The MT-600/8000 Series front bezel is NEMA 4 rated. When installed properly in a
Rating
NEMA 4 panel, the NEMA 4 rating of the panel will not be compromised. This means
that fluids will not enter the panel during wash downs.
Electrical
The MT-600/8000 Series has been tested to conform to European CE requirements.
Environment
This means that the circuitry is designed to resist the effects of electrical noise. This
does not guarantee noise immunity in severe cases. Proper wire routing and
grounding will insure proper operation.
Mechanical
Avoid installing units in environments where severe mechanical vibration or shocks
Environment
are present.
2.0 Installation Instructions
1
2.1 Mounting Instructions
4
2.1.1 Location Considerations
8
Care should be taken when locating equipment behind the unit to ensure that AC power wiring, PLC
output modules, contactors, starters and relays, and any other source of electrical interference are located
away from the back of the unit.
Particular note should be taken to the position of variable speed drives and switching power supplies.
Their input and load cables should be screened to a central star earth point.
MT-600/8000 series
MT-612X / MT-8121X
Installation Instruction
1
Advertisement
Table of Contents
Related Manuals for weintek MT-600 series
Summary of Contents for weintek MT-600 series
-
Page 1: Installation Instruction
MT-600/8000 series MT-612X / MT-8121X Installation Instruction 1.0 Installation and Startup Guide Install Environment Where The MT-600/8000 Series is designed for industrial. The temperature range of operating Used is from 32 to 113 °F (0 to 45 °C) , as majority of industrial environments. It may not be suitable for using in certain outdoor applications. -
Page 2: Making A Nema-4 Mounting
2.1.2 Making a NEMA-4 Mounting Panel The unit can be mounted into panels with a depth of 4”(105mm). It is recommended that Details the unit be mounted on the front panel of a steel enclosure, through an appropriate opening*. Allow a clearance of 1”(25mm) around the sides of the unit for mounting hardware. -
Page 3: Grounding Requirements
Caution Do not power the MT-600/8000 and inductive DC loads, or input circuitry Supply Voltage to the controller, with the same power supply. Note: The 24 VDC output Condition from some controllers may not have enough current to power the MT-600/8000. -
Page 4: Communications Connections
ICS 3-304.81 Safety Recommendations: Consideration should be given to the use of an emergency stop function, which is independent of the programmable controller. Where the operator is exposed to the machinery, such as in loading or unloading a machine tool, or where the machine cycles automatically, consideration should be given to the use of an electromechanical override or other redundant means, independent of the programmable controller, for starting and interrupting the cycle. - Page 5 2.3.2 Connector COM1[RS485] , COM3[RS485] and COM3[RS232] The 9 Pin, Female, SUB-D, COM1 [RS-485], COM3 [RS-485] and COM3 [RS-232] Port on the back of the unit is the RS-232 and RS485/422 communications port for connecting to a controller. COM1 [RS485]2w supports MPI 187.5K Connection Pin assignment of the 9 Pin, Female, SUB-D COM1 [RS-485], COM3 [RS-485] and COM3 [RS-232] Port...
- Page 6 Weintek products include the isolated power supply are covered by a limited liability warranty from defects in material and workmanship. This warranty does not apply : (a) if, in the judgment of Weintek, the product fails due to damage from shipment, handling, storage, accident (natural and man-mad) ;...
-
Page 7: Specifications
3.0 Specifications MT612X MT8121X Hardware Specification Display 12.1" TFT Brightness 400 cd/m Color 65,536 colors Contrast Ratio 500:1 Resolution (WxH dots) 800 x 600 Back light CCFLx2 CCFL life time 50,000 hr. min. Touch panel 4 wires resistive type Active Area Length(X)±2%, Width(Y)±2% Touch Accuracy Surface Hardness COM1 (RS-232/RS-485 2W/4W), COM2(RS232), COM3(RS-232/RS-485 2W) - Page 8 4.0 Dimensions of MT-612X / MT-8121X VIP1 VIP2 RESET Cutout Dimensions: Cutout Dimensions: MT612X / MT8121X: T612X / MT8121X: FUSE 305mm [12.01"] W x 231mm [9.09"] H 305mm [12.01”] Wx231mm [9.09”] H 24VDC FG COM1 [RS485 2/4W] COM3 [RS485] COM1 [RS232] COM3 [RS232] COM2 [RS232] Panel-mounting clamp slots, 9 places...