Harman Kardon HK 990/230 Service Manual page 75

Philips Semiconductors
2
16-bit I C and SMBus I/O port with interrupt
FEATURES
•
Operating power supply voltage range of 2.3 V to 5.5 V
•
5 V tolerant I/Os
•
Polarity inversion register
•
Active-LOW interrupt output
•
Low stand-by current
•
Noise filter on SCL/SDA inputs
•
No glitch on power-up
•
Internal power-on reset
•
16 I/O pins which default to 16 inputs
•
0 kHz to 400 kHz clock frequency
•
ESD protection exceeds 2000 V HBM per JESD22-A114,
200 V MM per JESD22-A115, and 1000 V CDM per
JESD22-C101
•
Latch-up testing is done to JESDEC Standard JESD78 which
exceeds 100 mA
•
Five packages offered: DIP24, SO24, SSOP24, TSSOP24, and
HVQFN24
ORDERING INFORMATION
PACKAGES
24-Pin Plastic DIP
24-Pin Plastic SO
24-Pin Plastic SSOP
24-Pin Plastic TSSOP
24-Pin Plastic HVQFN
Standard packing quantities and other packaging data are available at www.standardproducts.philips.com/packaging.
2
I C is a trademark of Philips Semiconductors Corporation.
SMBus as specified by the Smart Battery System Implementers Forum is a derivative of the Philips I
2004 Sep 30
TEMPERATURE
ORDER CODE
RANGE
–40 °C to +85 °C
PCA9555N
–40 °C to +85 °C
PCA9555D
–40 °C to +85 °C
PCA9555DB
–40 °C to +85 °C
PCA9555PW
–40 °C to +85 °C
PCA9555BS
DESCRIPTION
The PCA9555 is a 24-pin CMOS device that provide 16 bits of
General Purpose parallel Input/Output (GPIO) expansion for
2
I C/SMBus applications and was developed to enhance the Philips
family of I@C I/O expanders. The improvements include higher drive
capability, 5 V I/O tolerance, lower supply current, individual I/O
configuration, and smaller packaging. I/O expanders provide a
simple solution when additional I/O is needed for ACPI power
switches, sensors, pushbuttons, LEDs, fans, etc.
The PCA9555 consist of two 8-bit Configuration (Input or Output
selection); Input, Output and Polarity inversion (Active-HIGH or
Active-LOW operation) registers. The system master can enable the
I/Os as either inputs or outputs by writing to the I/O configuration
bits. The data for each Input or Output is kept in the corresponding
Input or Output register. The polarity of the read register can be
inverted with the Polarity Inversion Register. All registers can be
read by the system master. Although pin-to-pin and I
compatible with the PCF8575, software changes are required due to
the enhancements and are discussed in Application Note AN469 .
The PCA9555 open-drain interrupt output is activated when any
input state differs from its corresponding input port register state and
is used to indicate to the system master that an input state has
changed. The power-on reset sets the registers to their default
values and initializes the device state machine.
Three hardware pins (A0, A1, A2) vary the fixed I
allow up to eight devices to share the same I
2
I C address of the PCA9555 is the same as the PCA9554 allowing
up to eight of these devices in any combination to share the same
2
I C/SMBus.
TOPSIDE MARK
PCA9555
PCA9555D
PCA9555
PCA9555
9555
73
Product data sheet
PCA9555
2
C address
2
C address and
2
C/SMBus. The fixed
DRAWING NUMBER
SOT101-1
SOT137-1
SOT340-1
SOT355-1
SOT616-1
2
C patent.