Harman Kardon HK 990/230 Service Manual page 15

www.ti.com
FEATURES
• I 2 C to Parallel Port Expander
• Open-Drain Active-Low Interrupt Output
• Operating Power-Supply Voltage Range of
2.3 V to 5.5 V
• 5-V Tolerant I/Os
2
• 400-kHz Fast I C Bus
• Three Hardware Address Pins Allow up to
Eight Devices on the I
• Input/Output Configuration Register
• Polarity Inversion Register
• Internal Power-On Reset
DB, DBQ, DGV, DW,
OR PW PACKAGE
(TOP VIEW)
A0 1
A1 2
A2 3
P0
4
P1 5
P2
6
P3 7
GND 8
DESCRIPTION/ORDERING INFORMATION
This 8-bit I/O expander for the two-line bidirectional bus (I
provides general-purpose remote I/O expansion for most microcontroller families via the I
clock (SCL), serial data (SDA)].
The PCA9554A consists of one 8-bit Configuration (input or output selection), Input, Output, and Polarity
Inversion (active high or active low) registers. At power-on, the I/Os are configured as inputs with a weak pull up
to V . However, the system master can enable the I/Os as either inputs or outputs by writing to the I/O
CC
configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The
polarity of the Input Port register can be inverted with the Polarity Inversion register. All registers can be read by
the system master.
The system master can reset the PCA9554A in the event of a timeout or other improper operation by utilizing
the power-on reset feature which puts the registers in their default state and initializes the I
machine.
The PCA9554A open-drain interrupt (INT) output is activated when any input state differs from its corresponding
Input Port register state and is used to indicate to the system master that an input state has changed.
INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the
remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via
2
the I C bus. Thus, the PCA9554A can remain a simple slave device.
The device's outputs (latched) have high-current drive capability for directly driving LEDs and low current
consumption.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
2 C/SMBus
RGV PACKAGE
16
V
CC
16
15
SDA
A2 1
14
SCL
P0
2
13 INT
P1
3
12
P7
11 P6
P2 4
10
P5
5
9
P4
document contains
REMOTE 8-BIT I
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
• Power-Up With All Channels Configured as
Inputs
• No Glitch on Power-Up
• Latched Outputs With High-Current Drive
Maximum Capability for Directly Driving LEDs
• Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
• ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
(TOP VIEW)
15 14 13
12 SCL
INT
11
P7
10
9 P6
6 7 8
2
C) is designed for 2.3-V to 5.5-V V
Copyright © 2006–2007, Texas Instruments Incorporated
13
2
C AND SMBus I/O EXPANDER
RGT PACKAGE
(TOP VIEW)
16 15 14 13
A2 SCL
1 12
P0 INT
2 11
P1 P7
3 10
P2 P6
4 9
5 6 7 8
CC
2
C interface [serial
2
C/SMBus state
PCA9554A
operation. It