Advertisement
Advertisement
Table of Contents
Related Manuals for Harman Kardon HK 990
Summary of Contents for Harman Kardon HK 990
- Page 1 HK 990 Integrated Amplifier Owner’s MAnuAl...
- Page 2 Table of Contents Important Safety Instructions 2 safety Instructions 1. Read these instructions. 13. Refer all servicing to qualified service person- nel. servicing is required when the apparatus has 3 Introduction and features 2. Keep these instructions. been damaged in any way, such as power supply 4 front Panel Controls and functions cord or plug is damaged, liquid has been spilled 3.
- Page 3 Rls IV digital-to-analog conversion amplifier when placed in a cabinet technology, with dual conversion using two In terms of raw power, the HK 990 is the most stereo aD1955 high-grade DaCs in Dual • Harman Kardon system remote for control of...
-
Page 4: Controls And Functions
5 Input Setup Button: Press this button to both ”speaker 1” and ”2” selectors in the off to turn on the HK 990; press it again to turn the enter/exit the Input setup Mode. Here you can position, output is supplied only to headphones. - Page 5 Magnet (high output and high impedance) or A TV input jacks for analog sound input from High-output Moving Coil cartridge. R Remote In. To control your HK 990 with an your TV. external infrared remote sensor, connect the L Phono Input for record player with Moving B TaPe input jacks for analog tape replay.
- Page 6 ONLY if the impedance of component’s Input/Record jacks to the output EACH speaker is NOT LESS THAN 8 Ohms. jacks of the HK 990. Use the white, black or WARNING: Do not play sets of speakers gray plugs to connect left channel jacks; use the red plugs for Right channel jacks.
-
Page 7: Remote Control
Display: switches the display brightness of prevent damage from corrosion. the HK 990 and other HK units in steps of full brightness, Reduced brightness and Display off. Numeric Buttons (0-9): Used to enter track numbers on CD or CDR units or to enter preset numbers/frequency digits on a Tuner. - Page 8 CD player’s display) and a second time to establish an end point (shown as Rep a-b in the Volume +/- : Press to adjust the HK 990 vol- CD player’s display). The music between these ume up or down.
- Page 9 Folder - (repeating button) folder - Rep A-B Rep a-b Rep a-b Random Random Random This function list shows all functions of the HK 990 and external devices that can be controlled by the HK 990 remote. ReMoTe fUnCTIon lIsT...
-
Page 10: Setup Instructions
HK 990 stereo integrated amplifier: associated with each Input in the Input setup Procedure also determines the recording signal each Input of the HK 990 can be configured to • source listen: CD source when you select that device in the Record match the system and your personal taste. -
Page 11: Speaker Setup
If no error is found, If you want to benefit from the HK 990’s acoustics, but also corrects the high frequency the system will bring you to step 3. If you... -
Page 12: Level Settings
EQ Preset listening position. after pressing enter, two sweeps are generated. If successful The HK 990 provides direct access to the three you will jump to step 7. If not, the fol- set of filters via the Remote Control through the lowing message is shown: “sub 1 or 2... -
Page 13: Operating Instructions
Listening to your CD player, tape With the Input setup, you may adjust bass and have connected a cd player to the HK 990 with deck, tuner or other source Treble as well as balance if you have not already a digital cable, its signal is available from the done this during the setup process. -
Page 14: Specifications
Depth includes Volume Button and Loudspeaker Terminals Weight 24 kg 250 Crossways Park Drive, Woodbury, new York 11797 www.harmankardon.com Harman Consumer Group International: 2, Route de Tours, 72500 Château-du-loir, france © 2008 Harman Kardon, Incorporated Part no. 8509 9012 0000...