Related Manuals for OT Systems FT210AB Series
Summary of Contents for OT Systems FT210AB Series
-
Page 1: Installation And Operation Manual
FT210AB Series Installation & Operation Manual Installation and Operation Manual FT220AB Series 10-bit Digital Series 2-chVideo with 2-ch Duplex Audio Fiber Optic Converter OT Systems Ltd., 2014 Rev 1.2 www.ot-systems.com... - Page 2 FT210AB Series Installation & Operation Manual Models covered in this manual Standalone Units Card Modules Single-Mode Transmitters Single-Mode Transmitters FT220AB-SSTSA FT220AB-SST FT220AB-SSTLSA FT220AB-SSTL Single-Mode Receivers Single-Mode Receivers FT220AB-SSRSA FT220AB-SSR FT220AB-SSRLSA FT220AB-SSRL Multi-Mode Transmitter Multi-Mode Transmitter FT220AB-SMTSA FT220AB-SMT Multi-Mode Receiver Multi-Mode Receiver...
-
Page 3: Table Of Contents
FT210AB Series Installation & Operation Manual Table of Contents SAFETY INSTRUCTIONS ..........................4 PRODUCT OVERVIEW ............................ 5 ..............................5 NTRODUCTION ............................6 ODELS SELECTION TABLE INSTALLATION..............................7 ................................7 ENERAL ..........................7 TANDALONE UNIT INSTALLATION ........................... 8 ARD MODULE INSTALLATION CABLE CONNECTIONS &... -
Page 4: Safety Instructions
FT210AB Series Installation & Operation Manual (1) Safety Instructions Please be familiar with all information in this manual prior to installation and operation. Note 1: The products described contain a Class 1 laser or LED fiber optic emitter. The following safety precautions apply. -
Page 5: Product Overview
FT210AB Series Installation & Operation Manual (2) Product Overview 2.1 Introduction The FT220AB Series products comprise of either single-mode or multi-mode fiber optic transmitters and receivers for the optical transmission of TWO forward (Tx → Rx) video and TWOduplex (Tx ↔ Rx) audio signal on one fiber. The products work at wavelengths of 1310nm and 1550nm with either a 9/125um or 62.5/125um fiber for single-mode or multi-mode... -
Page 6: Models Selection Table
FT210AB Series Installation & Operation Manual 2.2 Models selection table Installation Models Descriptions Remarks requirements FT220AB-SSTSA Single-mode 2-Ch. Video Transmitter & Horizontally or FT-PA/12V 2-Ch. Audio Transceiver Standalone vertically external Unit wall-mounted power FT220AB-SSTLSA Single-mode Long-haul 2-Ch. Video Standalone supply is... -
Page 7: Installation
(3) Installation 3.1 General All OT Systems products are thoroughly inspected, tested and securely packaged before delivery to ensure a stable, intact and trouble-free service. Please check the equipment upon receipt for any visible damage which may have been caused during shipping. -
Page 8: Card Module Installation
FT210AB Series Installation & Operation Manual With all the signals available at the input and output ports, check the status of LEDs located on the unit. With correct status of each LED, installation is now completed [for LEDs status, see Operational Guides on this manual’s section (5)]. - Page 9 FT210AB Series Installation & Operation Manual Standalone Transmitter Standalone Receiver Fig 4.1 Standalone unit to Standalone unit connection diagram Standalone Transmitter Card Module Receiver Fig 4.2 Standalone unit to Card Module connection diagram www.ot-systems.com...
- Page 10 FT210AB Series Installation & Operation Manual Card Module Transmitter Card Module Receiver Fig 4.3 Card Module to Card Module connection diagram www.ot-systems.com...
-
Page 11: Audio Port Assignment And Pin Connections
FT210AB Series Installation & Operation Manual 4.2 Audio port assignment and pin connections For audio input and output connections, please note the following pin assignment: Pin Assignment (Screw Terminal Block) Data format Balanced signal IN (+) IN(-) OUT(+) OUT(-) Un-Balanced signal Sig. -
Page 12: Ground Connection
FT210AB Series Installation & Operation Manual 4.3 Ground connection For enhanced safety to reduce the risks of electrical shock and physical damage, caused by lightning and other power surges, as well as a connection to the surge suppresion devices in the product, a screw terminal is provided on the Standalone cabinets (Fig. -
Page 13: Ft220Ab Series Receiver
FT210AB Series Installation & Operation Manual 5.2 FT220AB Series Receiver LED Indicators Indicator Color Description Lit when power is supplied to the Receiver. Yellow Lit when optical signal from transmitter to receiver is active. VIDEO Green OUT / Lit when video signals are received at VIDEO OUT connectors. -
Page 14: Specifications
FT210AB Series Installation & Operation Manual (6) Specifications MODELS* FT220AB-SST(R)SA FT220AB-SST(R)LSA FT220AB-SMT(R)SA FT220AB-SST(R) FT220AB-SST(R)L FT220AB-SMT(R) PARAMETERS (Single-Mode) (Single-Mode) (Multi-Mode) OPTICAL No. of Fiber / Connector 1 / ST (or FC) 1 / ST (or FC) 1 / ST (or FC) -
Page 15: Drawings
Fig. 7.1 Dimensional drawings of Standalone unit (mm) (8) Warranty Information All OT Systems FT Series products are subject to a limited life-time warranty offered by the company in normal circumstances. Please refer to the OT Systems Products Warranty Statement for details. Access to the statement is available in our company website at www.ot-systems.com. -
Page 16: Contact Information
FT210AB Series Installation & Operation Manual (9) Contact Information APAC Operation EMEA Operation AMERICAS Operation Address: Address: Address: Unit 1023, 10/F, Landmark J. Slovackio str. 4, LT-11107, 18 West Main Street, Plano, North, 39 Lung Sum Avenue, Vilnius, Lithuania IL 60545, U.S.A.
Need help?
Do you have a question about the FT210AB Series and is the answer not in the manual?
Questions and answers