City Code Table; Troubleshooting; Specifications - Casio 5499 Operation Manual

Troubleshooting

Time Setting
■ Why is the current time setting off by a couple of hours?
Your Home City setting may be wrong (page E-14). Check your Home City setting and correct it, if necessary.
■ Why is the current time setting off by one hour?
You may need to change your Home City's standard time/daylight saving time (DST) setting. Use the
procedure under "To change the current time and date settings" (page E-16).
Sensor modes
■ Why can't I change the temperature unit setting?
The temperature unit setting is always Celsius (°C) whenever TOKYO is selected as the Home City. In
this case, the setting cannot be changed.
■ Why does "ERR" appear while a sensor operation is in progress?
Subjecting the watch to strong impact can cause sensor malfunction or improper contact of internal
circuitry. When this happens, ERR (error) will appear on the lower display and sensor operations will be
disabled.
E-40
Battery
■ Why is the low battery alert flashing?
Battery power is low. Watch operations are disabled while the low battery
alert is flashing on the lower display.
If the low battery alert disappears after battery power recovers but then
starts to flash again after a short while, it means that you need to have
the watch's batteries replaced.
Low battery alert
E-42
World Time: 48 cities (31 time zones)
Other: daylight saving time/standard time
Alarms: 5 daily alarms (with one snooze alarm); Hourly Time Signal
Illumination: LED (light-emitting diode); Selectable illumination duration (approximately 1.5 seconds or
3 seconds); Auto Light
Other: Button operation tone on/off; Hand shifting (to view digital display)
Battery: Two silver oxide batteries (Type: SR927W)
Approximate battery operating time: 2 years under the following conditions:
• 1 illumination operation (1.5 seconds) per day
• Alarm: 10 seconds/day
• Temperature readings: Once/week
Frequent use of illumination runs down the batteries. Particular care is required when using auto light
(page E-38).
Specifications are subject to change without notice.
E-44

City Code Table

City UTC Offset/
City
Code GMT Differential
PPG Pago Pago –11
HNL Honolulu –10
ANC Anchorage –9
YVR Vancouver
–8
LAX Los Angeles
YEA Edmonton
–7
DEN Denver
MEX Mexico City
–6
CHI Chicago
NYC New York –5
YHZ Halifax –4
YYT St. Johns –3.5
SCL Santiago
–3
RIO Rio De Janeiro
Fernando de
FEN –2
Noronha
RAI Praia –1
L-2
Operation Guide 5499
City UTC Offset/
City
Code GMT Differential
UTC
LIS Lisbon 0
LON London
MAD Madrid
PAR Paris
ROM Rome +1
BER Berlin
STO Stockholm
ATH Athens
CAI Cairo +2
JRS Jerusalem
MOW Moscow
+3
JED Jeddah
THR Tehran +3.5
DXB Dubai +4
KBL Kabul +4.5
KHI Karachi +5
• If ERR appears while a measurement operation is being performed in a sensor mode, restart the
measurement. If ERR appears on the lower display again, it can mean there is something wrong with
the sensor.
• If ERR keeps appearing during measurement, it could mean there is a problem with the applicable
sensor.
World Time Mode
■ The time for my World Time City is off in the World Time Mode.
This could be due to incorrect switching between standard time and daylight saving time.
See "To specify standard time or daylight saving time (DST) for a city" (page E-30) for more information.

Specifications

Accuracy at normal temperature: ±15 seconds a month
Digital Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Two display formats (month, day or time); Home City code (can be assigned one of 48 city
codes); standard time / daylight saving time (summer time)
Analog Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds
Thermometer:
Measurement and display range: –10.0 to 60.0°C (or 14.0 to 140.0°F)
Display unit: 0.1°C (or 0.2°F)
Measurement timing: Every five seconds in the Thermometer Mode
Other: Calibration; Selectable measurement unit
Temperature Sensor Precision:
±2°C (±3.6°F) in range of –10°C to 60°C (14.0°F to 140.0°F)
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 23:59' 59.99"
Measuring modes: Elapsed time, split time, two finishes
Countdown Timer:
Measuring unit: 1 second
Countdown range: 60 minutes
Setting ranges: Countdown start time (1 to 60 minutes, 1-minute increments)
City UTC Offset/
City
Code GMT Differential
DEL Delhi +5.5
KTM Kathmandu +5.75
DAC Dhaka +6
RGN Yangon +6.5
BKK Bangkok +7
SIN Singapore
HKG Hong Kong
+8
BJS Beijing
TPE Taipei
SEL Seoul
+9
TYO Tokyo
ADL Adelaide +9.5
GUM Guam
+10
SYD Sydney
NOU Noumea +11
WLG Wellington +12
Temperature
Measurement
• This table shows the city codes of this watch.
(As of January 2016)
• The rules governing global times (GMT
differential and UTC offset) and summer time
are determined by each individual country.
E-41
E-43
L-1
L-3