Advertisement

Quick Links

ROADRECORDER® 7006 SERIES
USER GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the roadrecorder 7006 series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Safety Vision roadrecorder 7006 series

  • Page 1 ROADRECORDER® 7006 SERIES USER GUIDE...
  • Page 2: Important Notices

    It is shared with your company for the sole purpose of helping you with the operation of the described equipment. Safety Vision makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
  • Page 3: Table Of Contents

    ROADRECORDER® 7006 NVR USER GUIDE Components Installation Air Filter Replacement Video Retrieval 50-000001 LCD Control Panel Configuration Connecting to the NVR Help Windows Product Details Live View Snapshot Viewer Video Out Firmware / Config Storage Network Settings Date / Time Change Password Startup &...
  • Page 4: Components

    ROADRECORDER® 7006 NVR USER GUIDE Components Front Panel 1 - Status LEDs - See table at right. 2 - External GPS Input (top) - Connect the Garmin® GPS antenna. 3 - CANBUS (bottom) - Connect option CANBUS compatible accessories. 4 - USB Port (top) - USB 2.0.
  • Page 5 ROADRECORDER® 7006 NVR USER GUIDE Rear Panel 1 - Sensor Inputs and Ignition and Relay Outputs - See diagram below. 2 - Camera Ports - Camera inputs A1 through A6. Each input is power over Ethernet (POE) enabled. 3 - Air Filter Housing - Air intake that houses a replaceable air filter.
  • Page 6 ROADRECORDER® 7006 NVR USER GUIDE LCD Control Panel 50-000001 The 50-000001 LCD Control Panel is designed to provide advanced functionality with the RoadRecorder 7006 NVR. See the 50-000001 LCD Control Panel chapter for more information. 1 - LCD Display - Displays alerts and statuses. 2 - Esc Button - Press the Esc Button to cancel the current command a return to the display.
  • Page 7: Installation

    ROADRECORDER® 7006 NVR USER GUIDE Installation Main Wiring Diagram...
  • Page 8 Be aware that removing and reconnecting power to the NVR in short periods of time (such as during some vehicle maintenance procedures) may cause hard drive failure, leading to corrupt recorded video and other data. Safety Vision recommends properly shutting down the NVR before removing the main power harness when cycling of the vehicle’s power is to occur: 1.
  • Page 9: Flat Mount

    ROADRECORDER® 7006 NVR USER GUIDE Flat Mount Secure the RoadRecorder 7006 NVR assembly to a secure flat surface with appropriate fasteners. NOTE: Ensure that the front panel of the RoadRecorder 7006 NVR remains visible and accessible. Do not install the RoadRecorder 7006 NVR in an area of the vehicle cabin that could interfere with the safe operation of the vehicle.
  • Page 10: Air Filter Replacement

    ROADRECORDER® 7006 NVR USER GUIDE Air Filter Replacement The RoadRecorder 7006 NVR includes a replaceable air filter behind the rear air intake to protect the internal components from potential contaminates. Use the following procedure to replace the air filter. Remove the T10 security bit screw securing the filter housing to the front panel.
  • Page 11: Video Retrieval

    ROADRECORDER® 7006 NVR USER GUIDE Video Retrieval Use the following procedure to remove the hard drive. Ensure the hard drive is not being accessed. Insert the key as shown and turn it 90 degrees to the left. Push the plunger to extend it. Push the plunger again firmly to push the hard drive out.
  • Page 12: 50-000001 Lcd Control Panel

    NVR. This information may be the hard drive. Use the navigation key to highlight each useful when speaking with Safety Vision Technical Support. character of the password and press the center navigation key to enter it.
  • Page 13 ROADRECORDER® 7006 NVR USER GUIDE...
  • Page 14: Configuration

    ROADRECORDER® 7006 NVR USER GUIDE Configuration The RoadRecorder 7000 NVR can be configured through the on-board web interface, which must be accessed with a PC and web browser. Connecting to the NVR Use the following procedure to access the configuration web server using the default IP address: Connect the PC to the NVR’s Ethernet LAN RJ-45 port with a standard Ethernet cable.
  • Page 15: Help Windows

    ROADRECORDER® 7006 NVR USER GUIDE Help Windows Each screen of the RoadRecorder 7000 NVR configuration interface includes a comprehensive help menu. The help menus explain the functionality and parameters of each field. To access the help menu for a screen, simply click the Help button at the top right of the screen.
  • Page 16: Product Details

    ROADRECORDER® 7006 NVR USER GUIDE Product Details The Product Details page displays factory configured identification fields as well as the status of the removeable hard drive (primary) SafeStor (secondary). Product name: Model series of the NVR. Serial #: Individual serial number of the NVR (assigned at the factory).
  • Page 17: Live View

    ROADRECORDER® 7006 NVR USER GUIDE Live View The Live View allows you to see the field of view of a compatible connected camera, allowing you to focus and properly adjust the image. The Live View requires the installation of VLC Media Player, available free from the developer.
  • Page 18: Snapshot Viewer

    ROADRECORDER® 7006 NVR USER GUIDE Snapshot Viewer The Snapshot Viewer allows you to see still images taken from camera configured to record MJPEG. To view a camera’s snapshots, first select the camera. As the camera produces MJPEG still images, they will be available to view in sequential order.
  • Page 19: Video Out

    ROADRECORDER® 7006 NVR USER GUIDE Video Out The Video Out page configures the behavior of the video output when an optional external monitor is connected. First, select Sequence or Static in the Video Out Selection field. Sequence Select Sequence to have the output cycle between camera views.
  • Page 20: Firmware / Config

    A status bar appears as the firmware update is automati- the factory default. cally applied. Download NVR Firmware from Safety Vision If the connected PC has internet access, click this link to be directed directly to Safety Vision’s FTP site. Contact your Ac- count Executive for login information.
  • Page 21: Storage

    ROADRECORDER® 7006 NVR USER GUIDE Storage Primary Storage • Primary Storage Media Device Removable SSD is the only option available for the RoadRecorder 7006. • Primary Storage Media Setup Single Partition is by default enabled for Media Setup. Disk Cleanup Settings This option allows you to configure the setting for deleting files from Primary storage media and create...
  • Page 22: Network Settings

    ROADRECORDER® 7006 NVR USER GUIDE Network Settings The Network settings page configures the WLAN interface and SMTP server settings. Wireless Radio Interface Enter the IP address, Netmask, and the Gateway for the wireless local area network (WLAN) in 12 digit IP address format. These fields are critical when setting up a connection to a wireless network.
  • Page 23: Date / Time

    ROADRECORDER® 7006 NVR USER GUIDE Date / Time The Date / Time settings page configures allows modification of the NVR’s time zone. Timezone Select the time zone the vehicle travels in most frequently. Time Sync Priority Use the Time Sync Priority fields to select which device has priority in providing the NVR with time stamp data.
  • Page 24: Change Password

    ROADRECORDER® 7006 NVR USER GUIDE Change Password A password is required for the web interface and for offloading data via the LCD control panel. webUI Password To set a new password, enter the old password in the Old password field, and the new password in the New password and Confirm password fields, then click Change password.
  • Page 25: Startup & Shutdown

    ROADRECORDER® 7006 NVR USER GUIDE Startup & Shutdown The Startup & Shutdown page configures conditions when the NVR can automatically start and shut down. Startup Select the Enable startup due to acceleration option to automatically start the NVR and record an event (for the time entered in the Recording duration field) when the vehicle begins moving.
  • Page 26: Audio/Video Settings

    Rate. Additionally, select the check box in the Audio column to record audio with the stream. The RoadRecorder 7000 NVR supports both the Safety Vision SVC-2200 series Select the frames per second (FPS) for each camera channel. cameras in addition to Axis network cameras.
  • Page 27: Sensor Settings

    ROADRECORDER® 7006 NVR USER GUIDE Sensor Settings The Sensor Settings page configures settings for the sensors and fault statuses. Sensor Inputs For each sensor input, enter an alphanumerical name in the Name field and the number of volts (between 1 and 30) that cause the sensor to become active in the Threshold field.
  • Page 28: Recording

    File Size Enter the file size (in MB) that the NVR creates for continuous and event recording event recording. Safety Vision strongly recommends retaining the default settings of 100 Event Recorder Settings Enter the amount of time, in minutes, that elapse before and...
  • Page 29: Thresholds

    ROADRECORDER® 7006 NVR USER GUIDE Thresholds The Thresholds page configures the minimum and maximum values of specific equipment before events are recorded. Ignition Enter the minimum amount of voltage that must be applied during ignition to start up in the Startup minimum ignition value field.
  • Page 30: Gps / Geo Fence

    ROADRECORDER® 7006 NVR USER GUIDE GPS / GEO Fence The GPS / GEO Fence page configures the GPS signal priority and sets up the Geo Fence feature. GPS Priority Use the GPS Priority fields to select which device has priority in providing the NVR with GPS data.
  • Page 31: Camera

    ROADRECORDER® 7006 NVR USER GUIDE Camera The Camera diagnostics page provides comprehensive support for technicians installing and troubleshooting the NVR’s camera installation. Camera Status The Camera Status display shows the camera name, IP address, and operational status of each camera. Click on the camera’s name or IP address (depending on if you are connected through the WAN [top]...
  • Page 32: Sensor Status

    ROADRECORDER® 7006 NVR USER GUIDE Sensor Status The Sensor Status diagnostics page provides assistance when installing or troubleshooting the NVR’s sensors. Select a Refresh Interval (the frequency at which the web page will refresh) and the Test Duration (in minutes), then click Go. Sensor activation and their values can be observed in the display below.
  • Page 33: Recorder Status

    ROADRECORDER® 7006 NVR USER GUIDE Recorder Status The Recorder Status page allows you to download NVR logs and diagnostic reports, as well as display the status of the removeable hard drive (primary) SafeStor (secondary). NVR Status The status of the NVR is displayed as Recording, Configuring, Offloading, or Safetynet Offloading.
  • Page 34: Tag Events

    Tag Supervisor Event. This feature is useful in emergency situations where the web interface can be accessed wirelessly by a supervisor vehicle. (For more information regarding this feature, contact Safety Vision Technical Support.)
  • Page 35: Appendix A: Specifications

    ROADRECORDER® 7006 NVR USER GUIDE Appendix A: Specifications SPECIFICATIONS RoadRecorder 7006 NVR Maximum Video Resolution 2K × 2K Accelerometer 3-axis, 0.1 G resolution Maximum Framerate 30 fps per camera Camera Inputs 6 PoE 7 (plus ignition) / 2 Inputs / Outputs Hardware AES, DES, 3DES Encryption G.711, camera dependent (up to 6)
  • Page 36: Appendix B: Dimensions

    ROADRECORDER® 7006 NVR USER GUIDE Appendix B: Dimensions...
  • Page 37: Appendix C: Axis Device Configuration

    ROADRECORDER® 7006 NVR USER GUIDE Appendix C: Axis Device Configuration The RoadRecorder 7006 NVR supports both the Safety Vision SVC-2200 series cameras in addition to Axis network cameras. Configuration is identical except Axis cameras must be configured with the login and password both set to root.
  • Page 38: Appendix D: Gps Coordinate Conversion

    Enter the address of the required GPS location in Google Maps. Google Maps can be accessed at www. google.com/maps Safety Vision’s headquarters is used as an example. Confirm the appropriate address appears on the map as a red balloon marker.
  • Page 39 ROADRECORDER® 7006 NVR USER GUIDE...
  • Page 40 ROADRECORDER® 7006 NVR USER GUIDE FCC Compliance Statement NOTE This device has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 41 ROADRECORDER® 7006 NVR USER GUIDE...
  • Page 42 CORPORATE HEADQUARTERS 6100 W. Sam Houston Pkwy. N. Houston, TX 77041-5113 Main: 713.896.6600 Toll Free: 800.880.8855 Fax: 713.896.6640 www.safetyvision.com...

Table of Contents