Newco ACE-S Installation, Operation And Service Manual page 8

ACE SERIES BREWERS – REPLACEMENT PARTS LIST
ELECTRICAL COMPONENTS
Part No
100010 Warming plate ass'y 120 V, black
100187 Warming Element, 120 V 100 W
102581 Element main heating, 1100 W 120 V
102580 Element main heating, 1400 W 120 V
100071 Element main heating, 1750 W 120 V
102850 Element main heating, 3500 W 240 V
704227 Main thermostat
111593 Hi-limit Thermostat, manual reset
100085 Lighted rocker switch 120 V
201985 Brew switch, black, rectangular
102775 Dual lamp, brewing/ready indicating 120 V
102862 Micro switch &bracket ass'y
102841 Micro switch only
121723 Control board ass'y with bracket, (non TS models) 110322
111725 Control board ass'y with bracket, (TS models)
100500 ON/OFF switch
BREWBASKETS
110985 Brew basket assy, black plastic
201954 Filter pack brew basket
102800 Brew rail, LH
102799 Brew rail, RH
102370 Brew basket, S/S small
104010 Brew rail, RH, S/S basket
104011 Brew rail, LH, S/S basket
For additional replacement parts information refer to Ace Series replacement parts manual, P/N 108054.
PDS Flow Control Supplemental Information
The PDS flow control system is the result of many years of engineering effort to create a flow control valve that would be
accurate over a wide range of water pressures as well as maintain its volume setting for many years within the harsh
water environment that coffee brewing equipment must operate.
The valve has been designed to allow for adaptation to all varieties of brewers, and is available in both a low flow (0.15
GPM to 0.35 GPM) and high flow (0.56 to 1.25 GPM) model. Both models have adjustable flow rates to any setting
within the specified range. The low flow models are identifiable by their red bonnet while the high flow models have a
green bonnet. See item 14 in figure below.
Other features designed into the valve include an internal water strainer, a non-regulated water supply for connecting to
independent faucets, an easy to adjust knob for setting the flow rate, double O-ring swivel fittings to eliminate leaks due
to equipment being moved, and most importantly a porcelain sleeve and piston assembly that is self cleaning and
cannot be affected by chemicals within the water supply. The system has been designed to operate over a wide range
of water pressures, from 10 PSI to 70 PSI for low flow models and from 40 PSI to 110 PSI for high flow models, with an
accuracy of +/- 1%.
The time setting of the brewer timer works in conjunction with the flow rate set on the PDS valve. This determines the
volume of water being delivered for the brew cycle. If the valve is set at a rate of .25 GPM and the timer is set for 2
minutes, the volume delivered wil be .25 x 2 or one half gallon (64 oz). Refer to table 1 for other flow rates, timer settings
and volumes. Flow rate accuracy is critical as the timer setting will remain constant.
Description
TANK AND PLUMBING
Part No Description
102798 Tank ass'y, 120 V 1400 W
102859 Tank ass'y, 120 V 1750 W
102746 Tank ass'y, 240 V 3500 W
104012 Tank lid ass'y
781181 Gasket, silicone tank
100024 Sprayhead, S/S 5 hole
102820 Solenoid valve assembly with fittings
102780 Solenoid valve, S-45
201158 Repair kit, solenoid valve
790019 Gasket, flow control
100290 .250 flow control washer
102770 Faucet w/red handle
102268 Seat cup for faucet
PDS low/flow assembly
102783 Sprayhead tube ass'y
100025 Sprayhead gasket
MISC.
100078 Bumper foot with screw
108067 Probe ass'y, weldment
201173 Sprayhead nut
PAGE 8