Table Of Contents; Introduction; General; Job Data - Carrier AquaEdge 19XR series Installation Instructions Manual
Single-stage
semi-hermetic centrifugal liquid chillers
with pic ii controls and hfc-134a
50/60 hz
Hide thumbs
Also See for AquaEdge 19XR series:
Table of Contents
Advertisement
WARNING
Operation of this equipment with refrigerants other than
those cited herein should comply with ANSI/ASHRAE 15
(latest edition). Contact Carrier for further information on
use of this machine with other refrigerants.
DO NOT ATTEMPT TO REMOVE fittings, covers, etc.,
while machine is under pressure or while machine is run-
ning. Be sure pressure is at 0 psig (0 kPa) before breaking
any refrigerant connection.
CAREFULLY INSPECT all relief valves, rupture discs,
and other relief devices AT LEAST ONCE A YEAR. If
machine operates in a corrosive atmosphere, inspect the
devices at more frequent intervals.
DO NOT ATTEMPT TO REPAIR OR RECONDITION
any relief valve when corrosion or build-up of foreign
material (rust, dirt, scale, etc.) is found within the valve
body or mechanism. Replace the valve.
DO NOT install relief devices in series or backwards.
USE CARE when working near or in line with a com-
pressed spring. Sudden release of the spring can cause it
and objects in its path to act as projectiles.
CAUTION
Failure to follow these procedures may result in personal
injury or damage to equipment.
DO NOT STEP on refrigerant lines. Broken lines can whip
about and release refrigerant, causing personal injury.
DO NOT climb over a machine. Use platform, catwalk, or
staging. Follow safe practices when using ladders.
USE MECHANICAL EQUIPMENT (crane, hoist, etc.) to
lift or move inspection covers or other heavy components.
Even if components are light, use mechanical equipment
when there is a risk of slipping or losing your balance.
BE AWARE that certain automatic start arrangements
CAN ENGAGE THE STARTER, TOWER FAN, OR
PUMPS. Open the disconnect ahead of the starter, tower
fan, and pumps. Shut off the machine or pump before ser-
vicing equipment.
USE only repaired or replacement parts that meet the code
requirements of the original equipment.
DO NOT VENT OR DRAIN waterboxes containing
industrial brines, liquid, gases, or semisolids without the
permission of your process control group.
DO NOT LOOSEN waterbox cover bolts until the water-
box has been completely drained.
DOUBLE-CHECK that coupling nut wrenches, dial indi-
cators, or other items have been removed before rotating
any shafts.
DO NOT LOOSEN a packing gland nut before checking
that the nut has a positive thread engagement.
PERIODICALLY INSPECT all valves, fittings, and piping
for corrosion, rust, leaks, or damage.
PROVIDE A DRAIN connection in the vent line near each
pressure relief device to prevent a build-up of condensate
or rain water.
DO NOT re-use compressor oil or any oil that has been
exposed to the atmosphere. Dispose of oil per local codes
and regulations.
DO NOT leave refrigerant system open to air any longer
than the actual time required to service the equipment. Seal
circuits being serviced and charge with dry nitrogen to pre-
vent oil contamination when timely repairs cannot be com-
pleted.
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . 1,2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Job Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78
Receive the Machine . . . . . . . . . . . . . . . . . . 2
Rig the Machine . . . . . . . . . . . . . . . . . . . . . . . 3
Install Machine Supports . . . . . . . . . . . . . 31
Connect Piping . . . . . . . . . . . . . . . . . . . . . . . 34
EXCHANGERS
EXTENSION
Make Electrical Connections . . . . . . . . . 43
Install Field Insulation . . . . . . . . . . . . . . . . 78
INSTALLATION START-UP REQUEST
CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . . CL-1, CL-2
INTRODUCTION
The 19XR, 19XRV machine is factory assem-
General -
bled, wired, and leak tested. Installation (not by Carrier) con-
sists primarily of establishing water and electrical services to
the machine. The rigging, installation, field wiring, field pip-
ing, and insulation of waterbox covers are the responsibility of
the contractor and/or customer. Carrier has no installation
responsibilities for the equipment.
Job Data
Necessary information consists of:
• job contract or specifications
• machine location prints
• rigging information
• piping prints and details
• field wiring drawings
• starter manufacturer's installation details
• Carrier certified print
INSTALLATION
Step 1 - Receive the Machine
INSPECT SHIPMENT
Do not open any valves or loosen any connections. The
19XR, 19XRV machine may be shipped with a nitrogen
holding charge in both modules. Damage to machine may
result.
1. Inspect for shipping damage while machine is still on
shipping conveyance. If machine appears to be damaged
2
CONTENTS
CAUTION
Page
Advertisement
Table of Contents
