Black & Decker CD71CRE Instructions Manual page 4

ENGLISH
aged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g. Use the power tool, accessories and tool
bits etc., in accordance with these instruc-
tions, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qual-
ifi ed repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for
drills and impact drills
• Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
• Use auxiliary handles supplied with the
tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping sur-
faces when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed
metal parts of the power tool "live" and shock
the operator.
• Use clamps or another practical way to se-
cure and support the workpiece to a stable
platform. Holding the work by hand or against
your body leaves it unstable and may lead to
loss of control.
• Before drilling into walls, fl oors or ceilings,
check for the location of wiring and pipes.
• Avoid touching the tip of a drill bit just after drill-
ing, as it may be hot.
• This tool is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of experi-
ence and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for
their safety. Children should be supervised to
ensure that they do not play with the appliance.
• The intended use is described in this instruction
manual. The use of any accessory or attach-
ment or performance of any operation with this
tool other than those recommended in this in-
struction manual may present a risk of personal
injury and/or damage to property.
Vibration
The declared vibration emission values stated in
the technical data and the declaration of con-
formity have been measured in accordance with
a standard test method provided by EN 60745 and
may be used for comparing one tool with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which
the tool is used. The vibration level may increase
above the level stated.
When assessing vibration exposure to determine
safety measures required by 2002/44/EC to protect
persons regularly using power tools in employ-
ment, an estimation of vibration exposure should
consider, the actual conditions of use and the way
the tool is used, including taking account of all
parts of the operating cycle such as the times when
the tool is switched off and when it is running idle in
addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Electrical safety
This tool is double insulated; therefore no
earth wire is required. Always check that
the power supply corresponds to the volt-
age on the rating plate.
• If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to avoid
a hazard.
Features
This tool includes some or all of the following
features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
Assembly
Warning! Before assembly, make sure that the tool
is switched off and unplugged.
Fitting the side handle and depth stop (fi g. A)
• Turn the grip counterclockwise until you can
slide the side handle (7) onto the front of the
tool as shown.
4