Technical Data - Philips HP L1530R Service Manual

Technical Specifications
1.General
1.1.1Product description
HP L1530 is the 4th generation of Hudson 15" TFT Flat Panel Display
Monitor. It designed with PSWG, LVDS interface feature. The monitor
featured with both DVI -D and analog signal input interface, and
modularized as adisplay unit with embedded universal AC power
supplies inside monitor main body. The power button and display
control buttons (tact switch type) are on the front of the monitor. The
monitor shall support an internal scaler to automatically enable the
monitor to display lower resolution video modes into 1024 x 768 full
screen display. The image can be adjusted through OSD control board.
These adjustments can be stored on a board memory including 11 user
modes and 11 factory pre -set modes.
1.1.2 Desti n ation: AP, CN, EE, GB, LA, ME, SH, WE
1.2.Basic data
1.2.1LCD panel
1.2.1.1
Type NR.
Number of Pixels. : 1024 (H) x 768 (V)
Physical Size. : 326.5(H) x 253.5 (V) x 11.2(D) mm (Typ.)
Pixel Pitch. : 0.297 x 0.297 mm
Color pixel arrangement. : RGB stripes arrangement
Support Color. : 16M Colors (6 -bit with FRC)
Display Mode. : Normally White
Backlight. : CCFL edge light system
Active area. (WXH). : 304.1(H) x 228.1(V)mm (15" diagonal)
Viewing Angle. : Vertical 100 degree, Horizontal 130 degree (CR=10)
Contrast ratio.
Luminance. : 250 cd/m
1.2.1.2
Type NR.
Number of Pixels. : 1024 (H) x 768 (V)
Physical Size. : 326.5(H) x 253.5 (V) x 11.2(D) mm (Typ.)
Pixel Pitch. : 0.297 x 0.297 mm
Color pixel arrangement. : RGB vertical stripes
Support Color. : 16M Colors (6 -bit with FRC)
Display Mode. : Normally White
Backlight. : CCFL edge light system
Active area. (WXH). : 304.1(H) x 228.1(V)mm (15" diagonal)
Viewing Angle. : Vertical 130 degree, Horizontal 140 degree (CR=10)
Contrast ratio.
Luminance. : 250 cd/m
1.2.2. Power supply
Main Voltage: AC 90- 135 Vrms and 170– 265 Vrms, 50/60 ±2 Hz
Power consumption: 35 watts max.
Operating < 35W(typical with audio), standby<2W(with audio).
DC power switch off <2W(with audio)
.Power cord length: 1.8M
Power cord type: 3 lead with earth plug
Power indicator: LED (ON: green, Standby: amber)
Auto power saving: EPA, Nutek, VESA, DPMS,
STATUS H-sync V-sync
On On On
Stand-
Off On
by
Suspend On Off
Off Off Off
DC
Power
off
1.2.3. Horizontal scan: 30- 63 KHz
1.2.4. Vertical scan: 56- 76 Hz
1.2.5. Input signals

Technical Data

: LM150X08_A4K1 (LPL)
: 400:1
2
(Typ)
: CLAA150XP 01 (CPT.)
: 500:1
2
(Typ)
Video Power LED
Green
Active <35W
LCD
Amber
Blanked <2W
LCD
Amber
Blanked <2W
LCD
Amber
Blanked <2W
LCD
N / A <2W LCD Off
The input signals can be applied in two different modes:
1). VESA Analog
The video input consists of red, green, and blue signals. The
video signals are analog levels, where 0V corresponds to
black and 700mV is the maximum signal amplitude. Input
impedance of video pins is 75 ohm + - 1%. The capability of
sync signal inputs shall include separate sync. input
impedance: 2k2 ohmsThe signals are defined as follow:
Separate sync 3.3V and 5 voltTTL level , Positive/Negative
2). Intel DVI Digit a l
Input signal: Four channel TMDS signals . The digital interface
shall be comprised of 2 electrical layer component: a TMDS
interface for low -voltage differential serial encoding of the
digital display data(Panel Link compliant) and a DDC2B
electricalinterface.
1.2.6 Input connectors
Input analog D -sub connector pin assignment
(2) Input DVI-D connector pin assignment
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
3
HP L1530R
Go to cover page
Description
T.M.D.S. data2 -
T.M.D.S. data2+
T.M.D.S. data2 shield
No Connect
No Connect
DDC clock
DDC data
No Connect
T.M.D.S. data1 -
T.M.D.S. data1+
T.M.D.S. data1 shield
No Connect
No Connect
+5V Power
Ground (for +5V)– Cable detect
Hot plug detect
T.M.D.S. data0 -
T.M.D.S. data0+
T.M.D.S. data0 shield
No Connect
No Connect
T.M.D.S clock shi e ld
T.M.D.S. clock+
T.M.D.S. clock -