Programming Remotes - Chamberlain J Owner's Manual

PROGRAMMING REMOTES

STANDARD SINGLE BUTTON REMOTE
1. Press and release the RADIO button (LED will light).
2. Press and hold the remote control button until the LED flashes
rapidly, then release remote control button. The LED will then
remain on solid after releasing the button.
3. Press and release the RADIO button to complete the
programming. The programming mode is exited if no activity is
performed within 30 seconds.
NOTE: Single button remote is not supported with E2 and E2
failsafe wiring modes.
REMOTE OPEN, CLOSE AND/OR STOP BUTTON
(Allows transmitter to operate as a 3- button control system)
A remote may be programmed to function as a Wireless Open,
Close or Stop Button.
1. Press and release the RADIO button on the logic board (LED
will light).
2. Press and release
OPEN button on logic board (remote functions as an
OPEN button)
OR
STOP button on logic board (remote functions as a
STOP button)
OR
CLOSE button on logic board (remote functions as a
CLOSE button)
LED flashes rapidly and then remains on solid.
3. Press and hold the remote button until the LED flashes rapidly.
The LED will remain on solid after releasing.
NOTE: To add more remote functions or remotes repeat steps 2
and 3.
4. After learning remote press and release the RADIO button on
the logic board (LED flashes rapidly and then turns off).
NOTE: Requires self-monitoring photo eyes when using constant
pressure to close (wiring C2, D1 and E2).
P R O G R A M M I N G
OPEN
Open
Close
CLOSE
Stop
STOP
SINGLE BUTTON CONTROL (SBC) REMOTE
This function programs a remote as a Wireless Single Button
Control. In B2 mode, operation is
OPEN/STOP/CLOSE/REVERSE/STOP. In C2 mode, operation is
OPEN/STOP/Constant pressure to CLOSE/STOP on release. There
is no operation in D1 mode. In E2 mode, operation is
OPEN/STOP/Constant pressure to CLOSE/REVERSE on release. In
T and TS modes, operation is OPEN/STOP/CLOSE/REVERSE/STOP
and Timer to Close start/refresh. In FSTS mode, operation is OPEN
with Timer to Close start/refresh only bypassing all up mid stops.
Momentary and constant pressure commands are processed in
this function.
OPEN STOP
MODE
4 4
B2
4 4
C2
D1
4 4
E2
4 4
T, TS
4
FSTS
1. Press and release the RADIO button on the logic board (LED
will light).
2. Press and release the SBC externally wired button or TIMER on
the logic board (LED flashes rapidly and then remains on solid).
3. Press and hold the remote button until the LED flashes rapidly.
The LED will then remain on solid after releasing.
4. Press and release the RADIO button on the logic board (LED
flashes rapidly and then turns off). The programming mode is
exited if no activity is performed within 30 seconds.
ERASING REMOTES
Press and hold the RADIO button on the logic board until the
RADIO LED flashes rapidly (approximately 5 seconds).
All remotes will be erased.
NEW ON BOARD PROGRAMMING
P4
E1
R29
C11
D3Ø2
D1
EDGE
K3
D22
OPEN
D2Ø
OLS
CLOSE
D21
MID
SLS
D16
CLS
D13
P7
STOP
MRT
RADIO 1
D36
C77
D35
C73
L1
L5
P6
18
OPERATION
Constant
CLOSE Reverse
Pressure
4 4
4
4
4 4
Ø14LGØ657–A Ø14GPØ657–A
C3Ø
C18
D31
D7
D6
D5
X1 P1Ø
C25 D4
C17
24V
AC 14
POWER
24V
AC 13
D19
TIMER
J1 J3ØØ TIMER
DEFEAT
DEFEAT 12
D25
D17
R8
CMN 11
D24
MAS D28
MAS 10
D26
D23
4
EYES
D27
EYES 9
D15
MID TIMER
D1
EDGE
EDGE 8
D22 OPEN
D2Ø
TIMER
2 3 ENABLE
OPEN 7
CLOSE
D21
RELAY A
CLOSE 6
D13
STOP
RELAY B
STOP 5
T TS
CMN 4
E2 FSTS
D1 DIAG
3
C2
2
SBC
B2 PROG
FAILSAFE (B2 C2 D1 E2)
SBC 1
S8 NON FAILSAFE
D14
P1
F1
D34
Timer To
Close
4
4