Genie S-80 Service And Repair Manual
  1. Manuals
  2. Brands
  3. Genie Manuals
  4. Boom Lifts
  5. S-80
  6. Service and repair manual

Genie S-80 Service And Repair Manual

From s80/85/80x15-12264
Hide thumbs Also See for S-80:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service & Repair Manual, Service Manual
Service and Repair Manual
S-80
S-85
S-80X
from S80/85/80X15-12264
This manual includes:
Repair procedures
Fault Codes
Electrical and
Hydraulic Schematics
For detailed maintenance
procedures, refer to the
appropriate Maintenance
Manual for your machine.
Part No. 1269074
Rev A
September 2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S-80 and is the answer not in the manual?

Questions and answers

Related Manuals for Genie S-80

Summary of Contents for Genie S-80

  • Page 1 Service and Repair Manual S-80 from S80/85/80X15-12264 This manual includes: Repair procedures S-85 Fault Codes Electrical and S-80X Hydraulic Schematics For detailed maintenance procedures, refer to the appropriate Maintenance Manual for your machine. Part No. 1269074 Rev A September 2015...

  • Page 2: Introduction

    Copyright © 2015 by Terex Corporation 1269074 Rev A, September 2015 First Edition, First Printing "Genie" and "S" are registered trademarks of Terex South Dakota, Inc. in the USA and many other countries. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 3 Section – Repair Procedure, 4-2 Click on any content or procedure in the Table of Contents to view Section – Fault Codes, All charts the update. Section – Schematics, Legends and schematics Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 4: Serial Number Legend

    Service and Repair Manual September 2015 Introduction Serial Number Legend 1 Model 2 Model year 3 Sequence number 4 Serial number (stamped on chassis) 5 Serial label (located under cover) S-80 • S-85 • S-80X Part No. 1269074...

  • Page 5: Safety Rules

    You read, understand and obey: • manufacturer's instructions and safety rules • employer's safety rules and worksite regulations • applicable governmental regulations  You have the appropriate tools, lifting equipment and a suitable workshop. Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 6 Be aware of potential crushing hazards such as moving parts, free swinging or unsecured components when lifting or placing loads. Always wear approved steel-toed shoes. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 7: Table Of Contents

    Deutz TD 2.9 Engine Specifications ............... 8 Perkins 804D-33 Engine Specifications ..............9 Perkins 404F-22T Engine Specifications ............. 10 Machine Torque Specifications ................11 Hydraulic Hose and Fitting Torque Specifications ..........12 Torque Procedure ....................13 Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 8 How to Bleed the Platform Rotator ..............27 2-4 Platform Overload System ................28 Jib Boom Components ..................31 3-1 Jib Boom ......................31 3-2 Jib Boom Lift Cylinder ..................32 viii S-80 • S-85 • S-80X Part No. 1269074...
  • Page 9 Table of Contents Boom Components .................... 33 4-1 Cable Track ....................33 How to Remove the Cable Track, S-80 ............33 How to Repair the Cable Track ............... 35 4-2 Boom ......................35 How to Shim the Boom ................... 35 How to Remove the Boom ................
  • Page 10 8-3 Brake/Two-Speed Manifold Components ............60 8-4 Turntable Rotation Manifold Components ............. 61 8-5 Platform Rotate Manifold Components ............62 8-6 Platform Manifold Components, S-80 ............63 8-7 Platform Manifold Components, S-85 ............64 8-8 2WD Traction Manifold Components ............. 65 8-9 4WD Traction Manifold Components .............
  • Page 11 Continental TME27 Engine Fault Codes ............111 How to Retrieve Continental Engine Fault Codes......... 111 How to Clear Engine Fault Codes from the ECM ......... 111 Continental TME27 Engine Fault Codes ............112 Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 12 Electrical Schematic, S-80X - Continental TME27 Models (ANSI / CSA) ..168 Ground Control Box, S-80X - Continental TME27 Models (ANSI / CSA) ..172 Platform Control Box, S-80X - Continental TME27 Models (ANSI / CSA) ... 173 S-80 • S-85 • S-80X Part No. 1269074...
  • Page 13 September 2015 Table of Contents Electrical Schematics, S-80, S-85 – ANSI and CSA Models ......175 Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (ANSI / CSA) ..........176 Ground Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (ANSI / CSA) ..........180 Platform Control Box, S-80 •...
  • Page 14 Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (CE) ....216 Ground Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE) ....220 Platform Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE) ....221 Electrical Schematic, S-80 •...

  • Page 15: Specifications

    14 in 35.6 cm Lugs and Lug Nut Torque Wheel lugs 11 @ 3/4 - 16 Lug nut torque, dry 420 ft-lbs 569 Nm Lug nut torque, lubricated 320 ft-lbs 434 Nm Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 16: Performance Specifications

    Drive speed, maximum Hydraulic Fluid Specifications Stowed position, 40 ft / 7.9 - 8.5 sec Genie specifications require hydraulic oils which are RT tires 12.2 m / 7.9 - 8.5 sec designed to give maximum protection to hydraulic systems, have the ability to perform over a wide...
  • Page 17 Maximum continuous operating 124°F / 51°C temperature Note: Use of Chevron 5606A hydraulic fluid, or equivalent, is required when ambient temperatures are consistently below 0°F / -17°C unless an oil heating system is used. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 18: Hydraulic Component Specifications

    17.3 bar Flash point None Auxiliary Pump Pour point -81°F / -63°C Type: fixed displacement gear pump Maximum continuous operating 189°F / 87°C Displacement per revolution 0.15 cu in temperature 2.47 cc S-80 • S-85 • S-80X Part No. 1269074...

  • Page 19: Manifold Component Specifications

    Medium pressure filter Medium pressure filter bypass 51 psi pressure 3.5 bar Hydraulic tank return filter 10 micron with 25 psi / 1.7 bar bypass Beta 10 ≥2 Drive motor case drain return filter Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 20: Continental Tme27 Engine Specifications

    Above 5°F / -15°C 15W-40 Unit ships with 15W-40. Extreme operating temperatures may require the use of alternative engine oils. For oil requirements, refer to the Engine Operator Manual for your engine. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 21: Deutz Td2011L04I Engine Specifications

    Above 5°F / -15°C 15W-40 Unit ships with 15W-40. Extreme operating temperatures may require the use of alternative engine oils. For oil requirements, refer to the Engine Operator Manual for your engine. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 22: Deutz Td 2.9 Engine Specifications

    Above 5°F / -15°C 15W-40 Unit ships with 15W-40. Extreme operating temperatures may require the use of alternative engine oils. For oil requirements, refer to the Engine Operator Manual for your engine. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 23 10 liters Oil viscosity requirements Unit ships with 15W-40. Extreme operating temperatures may require the use of alternative engine oils. For oil requirements, refer to the Engine Operator Manual for your engine. Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 24 Above 5°F / -15°C 15W-40 CJ4 Unit ships with 15W-40. Extreme operating temperatures may require the use of alternative engine oils. For oil requirements, refer to the Engine Operator Manual for your engine. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 25: Machine Torque Specifications

    217 Nm Drive motor mounting bolts, dry 110 ft-lbs 149 Nm Drive motor mounting bolts, 80 ft-lbs* lubricated 108 Nm *(use blue threadlocking compound) Engine vibration isolators Compressed height 0.50” 12.7 mm Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 26: Hydraulic Hose And Fitting Torque Specifications

    Your machine is equipped with Parker Seal-Lok™ SAE Dash Size Torque ORFS or 37° JIC fittings and hose ends. Genie specifications require that fittings and hose ends 14 ft-lbs / 19 Nm be torqued to specification when they are removed 23 ft-lbs / 31.2 Nm...

  • Page 27: Torque Procedure

    Note: The O-ring in Parker Seal Lok™ fittings and hose end are custom-size O-rings. They are not standard size O-rings. They are available in the O-ring field service kit (Genie part number 49612). Lubricate the O-ring before installation. Be sure the O-ring face seal is seated and retained properly.

  • Page 28: September

    Tighten the hex nut until the mark on the hex nut is aligned with the second mark on the body hex fitting. Operate all machine functions and inspect the hose, fittings and related components to confirm there are no leaks. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 29: Repair Procedures

     Be sure that all necessary tools and parts are available and ready for use.  Use only Genie approved replacement parts.  Read each procedure completely and adhere to the instructions. Attempting shortcuts may produce hazardous conditions.

  • Page 30: About This Section

    Indicates that a specific result is expected after performing a series of steps. Indicates that an incorrect result has occurred after performing a series of steps. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 31: Platform Controls

    4 primary boom up/down and turntable rotate left/right joystick controller Remove the ALC-500 circuit board mounting fasteners. Carefully remove the ALC-500 circuit board from the platform control box. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 32: Joysticks

    10 seconds or until the alarm sounds. Connect the wire harness connector to the joystick. Move the joystick full stroke in either direction and hold for 5 seconds. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 33: How To Adjust The Joystick Max-Out Setting

    73 to 79 seconds Boom retract 79 to 84 seconds Turntable rotate, 360°boom fully 95 to 103 seconds stowed Drive speeds (factory settings) Stowed- high speed 7.9 to 8.5 seconds Non-stowed 40 to 45 seconds Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 34: How To Adjust The Joystick Ramp Rate Setting

    Momentarily activate the drive enable toggle switch in the right direction 6 times. Result: There should be a pause and the alarm should sound 6 times indicating that the machine is in ramp rate calibration mode. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 35: How To Adjust The Joystick Threshold Setting

    Result: The alarm does not sound. Repeat steps 3 through 7. decelerate, shift from high to low speed 4 seconds Start the engine from the platform controls and press down the foot switch. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 36: How To Calibrate The Boom Angle Sensor

    14 Cycle the red Emergency Stop button off, then Momentarily activate the drive enable toggle back on. switch to the right 1 time to set the stowed position. Note: The alarm will not sound indicating the setting. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 37 Result: The alarm will sound indicating that the settings have been saved and is leaving calibration mode. 11 Cycle the red Emergency Stop button off, then back on. Start the machine and return to the stowed position. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 38: Platform Components

    Cables can be damaged if they are kinked or pinched. Note: If your machine is equipped with an airline to platform option, the airline must be disconnected from the platform before removal. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 39: How To Remove The Platform Leveling Slave Cylinder

    Raise the primary boom to a horizontal the blocks. position. Move the platform level toggle switch up and down through two platform leveling cycles to remove any air that might be in the system. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 40: Platform Rotator

    Remove the platform. Refer to Repair Remove the pivot pin retaining fasteners from Procedure, How to Remove the Platform. both the slave cylinder rod-end pivot pin and the rotator pivot pin. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 41: How To Bleed The Platform Rotator

    Close the bleed screw. Crushing hazard. Keep clear of Note: When installing the platform rotator fasteners, the platform during rotation. torque the fasteners to specifications. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 42: Platform Overload System

    Using a suitable lifting device, place a test weight equal to the maximum platform capacity at the center of the platform floor. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 43 Note: The platform will need to be moved up and down and allowed to settle between each adjustment. Note: There may be a 2 second delay before the platform overload indicator lights and alarm responds. Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 44 Result: All ground control functions should operate normally. 14 Turn the key switch to platform control. 15 Test all machine functions from the platform controls. Result: All platform control functions should operate normally. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 45: Jib Boom Components

    Component damage hazard. fall when it is removed from the Cables and hoses can be machine if it is not properly damaged if they are kinked or supported by the overhead pinched. crane. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 46: Jib Boom Lift Cylinder

    Do not allow oil to squirt or spray. Remove the pin retaining fasteners from the jib boom lift cylinder rod-end pivot pin. Do not remove the pin. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 47: Boom Components

    Do not allow oil to How to R emove the C able Track , S-80 How to Remove the Cable Track squirt or spray. Note: When removing a hose assembly or fitting,...
  • Page 48 Remove the cable track guides from the boom. Component damage hazard. The cable track can be damaged 17 Remove the cable clamp from the pivot end of if it is twisted. the boom. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 49: How To Repair The Cable Track

    Measure each wear pad. Note: A cable track repair kit is available through Genie Service Parts, part no. 77896. The kit Boom wear pad specifications includes a 4-link section of cable track. Boom number one...

  • Page 50: How To Remove The Boom

    Note: A spreader bar and other hardware may be skills and tools could result in needed to safely remove the counterweight. death or serious injury and significant component damage. Dealer service is strongly recommended. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 51 19 Tag and disconnect all boom wire harness could fall if not properly electrical connectors located at the pivot end supported when the lift cylinder of the boom. rod-end pivot pin is removed. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 52: Boom Lift Cylinder

    Crushing hazard. The long and short link arms may fall if not properly supported when the boom pivot pins are removed. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 53 Do not allow oil to squirt or spray. Remove the pin retaining fasteners from the boom lift cylinder barrel-end pivot pins. Do not remove the pins. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 54: Boom Extension Cylinder

    Remove the access covers from both sides of Remove the cable retaining plates and pull the boom at the pivot end. the retract cables off of the pulleys. Lay the cables flat and out of the way. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 55 12 Pull back on the extend cable mounting plate until it clears the blocks welded to the inside of the number 1 boom tube. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 56: Boom Extend/Retract Cables

    Locate the retract cable adjustment nut on the bottom of the number 1 boom tube at the platform end of the boom. Loosen the nut, but do not remove the nut. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 57 2 1 6.375 inches / 16.2 cm Illustration 1 1 cable break limit switch 2 extend cable adjustment nut 3 extend cable pivot plate Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 58: How To Replace The Boom Extend/Retract Cables

    Install the new boom extend cable pulley, pivot pin and snap rings. Note: Be sure the boom extend cables are routed through the grooves of the pulley and the upper wear pad on the extension cylinder. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 59 1 boom tube, wrap the Note: A cable pulling tool is available through boom retract cables around the pulleys. Genie Service Parts Department (Genie part no. 94510) 22 Adjust the boom extend/retract cables. Refer to Repair Procedure, How to Adjust the Boom 12 At the platform end of the boom, pull on the Extend/Retract Cables.

  • Page 60: Platform Leveling Master Cylinder

    Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Remove the pin retaining fastener from the master cylinder barrel-end pivot pin. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 61: Engines

    Remove all rings, watches and other jewelry. Tag and disconnect the wiring plug at the electronic displacement controller (EDC), located on the drive pump. Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 62 Component damage hazard. Hoses can be damaged if they are kinked or pinched. Remove the flex plate mounting fasteners, and remove the flex plate from the engine flywheel. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 63 Component damage hazard. Hoses can be damaged if they are kinked or pinched. 12 Remove the flex plate mounting fasteners. Remove the flex plate from the engine flywheel. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 64: How To Install The Flex Plate

    Install the pump and pump mounting plate assembly onto the engine. Apply Loctite® removable thread sealant to the mounting screws. Deutz, Perkins and Continental Flex Plate S-80 • S-85 • S-80X Part No. 1269074...

  • Page 65: How To Install The Pump And Bell Housing Assembly

    Perkins 404F-22T Pump Mounting Plate Component damage hazard. Do not force the drive pump during installation or the flex plate teeth may become damaged. Continental Pump Mounting Plate Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 66: Ground Controls

    Test Desired result terminal 85 to 86 with resistor 75 to 85Ω terminal 87 to 87a and 30 no continuity (infinite Ω) terminal 87a to 30 continuity (zero Ω) S-80 • S-85 • S-80X Part No. 1269074...

  • Page 67: Hydraulic Pumps

    If the tank valves are closed, remove the key from the key switch and tag the machine to inform personnel of the condition. open closed Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 68: Drive Pump

    Do not allow oil to displacement controller (EDC), located on the squirt or spray. drive pump. Support the pumps with a suitable lifting device and remove the two drive pump mounting fasteners. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 69: How To Prime The Pump

    LPG hose to the LPG tank and open the valve on the tank. Deutz and Perkins models: Connect the engine wiring harness to the fuel solenoid. Start the engine from the ground controls and check for hydraulic leaks. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 70: Manifolds

    Pressure reducing valve Oscillate pressure control 30-35 ft-lbs / 41-47 Nm Differential sensing valve Differential 30-35 ft-lbs / 41-47 Nm sensing/turntable rotate Flow regulator valve Steering flow control 20-25 ft-lbs / 27-34 Nm S-80 • S-85 • S-80X Part No. 1269074...
  • Page 71 September 2015 Service and Repair Manual Manifolds Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 72: Function Manifold

    Repeat steps 2 through 5 and recheck relief Tip-over hazard. Do not adjust valve pressure. the relief valve higher than Remove the pressure gauge. specified. Repeat step 2 to confirm relief valve pressure. Remove the pressure gauge. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 73: How To Adjust The Boom Extend Relief Valve

    Then install the relief valve cap. Tip-over hazard. Do not adjust the relief valve higher than specified. Repeat steps 2 through 5 and recheck relief valve pressure. Remove the pressure gauge. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 74: Brake/Two-Speed Manifold Components

    Solenoid valve, 2 position 3 way Two-speed motor shift 20-25 ft-lbs / 27-34 Nm Check valve Brake release circuit 20-25 ft-lbs / 27-34 Nm Orifice, 0.025 inch / 0.63 mm Turntable rotation brake release S-80 • S-85 • S-80X Part No. 1269074...

  • Page 75: Turntable Rotation Manifold Components

    Turntable rotate right 25-30 ft-lbs / 34-41 Nm Shuttle valve, 2 position 3 way Turntable rotation brake release 8-10 ft-lbs / 10-15 Nm Orifice, 0.030 inch / 0.8 mm Brake release circuit Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 76: Platform Rotate Manifold Components

    The platform rotate manifold is mounted on the platform rotator. Index Schematic Description Function Torque Item Counterbalance valve, 3300 psi Platform rotate right 37-44 ft-lbs / 50-60 Nm Counterbalance valve, 3300 psi Platform rotate left 37-44 ft-lbs / 50-60 Nm S-80 • S-85 • S-80X Part No. 1269074...

  • Page 77: Platform Manifold Components, S-80

    September 2015 Service and Repair Manual Manifolds 8-6 Platform Manifold Com ponents, S-80 Platform Manifold Components, S-80 The jib boom/platform rotate manifold is mounted on the platform end of the boom. Index Schematic Description Function Torque Item Solenoid valve, 3 position 4 way...

  • Page 78: Platform Manifold Components, S-85

    20-25 ft-lbs / 27-34 Nm Pressure comp., flow control valve Platform rotate flow control 33-37 ft-lbs / 45-50 Nm Pressure comp., flow control valve Platform rotate flow control 33-37 ft-lbs / 45-50 Nm S-80 • S-85 • S-80X Part No. 1269074...

  • Page 79: 2Wd Traction Manifold Components

    Shuttle Valve, 3 position 3 way Controls flow to drive motors in 50-55 ft-lbs / 67-73 Nm forward and reverse Orifice Plug, 0.070 inch / 1.8 mm Equalizes flow across flow divider/combiner valve BY Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 80: 4Wd Traction Manifold Components

    Flow divider/combiner valve Controls flow to steer end drive 80-90 ft-lbs / 108-122 Nm motors in forward and reverse Check valve Non-steer end drive motor circuit 35-40 ft-lbs / 48-54 Nm S-80 • S-85 • S-80X Part No. 1269074...
  • Page 81 September 2015 Service and Repair Manual Manifolds Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 82: Drive Oil Diverter Manifold Components (Welder Option)

    35-40 ft-lbs / 47-54 Nm Pressure switch Power to relay 16 ft-lbs / 22 Nm Connector For pressure switch 11 ft-lbs / 15 Nm Check valve Prevents oil to generator 35-40 ft-lbs / 47-54 Nm S-80 • S-85 • S-80X Part No. 1269074...

  • Page 83: Valve Adjustments - Traction Manifold

    Turn the engine off and connect a 0 to 600 psi / 0 to 40 bar pressure gauge to the diagnostic nipple located on the traction manifold. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 84: Valve Coils

    Test the coil resistance. Result: The resistance should be within specification, plus or minus 30%. Result: If the resistance is not within specification, plus or minus 30%, replace the coil. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 85: How To Test A Coil Diode

    Result: If one or both of the current readings are 0 mA, or if the two current readings do not differ by a minimum of 20%, the coil and/or its internal diode are faulty and the coil should be replaced. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 86: Fuel And Hydraulic Tanks

    Explosion and fire hazard. When transferring fuel, connect a grounding wire between the machine and pump or container. Note: Be sure to only use a hand operated pump suitable for use with gasoline and diesel fuel. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 87: Hydraulic Tank

    Procedure, How to Remove the Fuel Tank. the return filter. Cap the fitting on the return filter housing. Tag and disconnect and plug the supply hose for the auxiliary power unit. Cap the fitting on the hydraulic tank. Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 88 16 Fill the tank with hydraulic oil until the level is within the top 2 inches / 5 cm of the sight gauge. Do not overfill. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 89: Turntable Rotation Components

    Do not allow oil to squirt or spray. Loosen the backlash pivot plate and adjustment bolts. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 90: How To Remove The Turntable Rotation Hydraulic Motor

    Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Remove the motor/brake mounting fasteners. Carefully remove the motor from the brake. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 91: How To Adjust The Turntable Rotation Gear Backlash

    Loosen the backlash pivot plate mounting fasteners. 1 motor 2 drive hub mounting bolts 3 drive hub with brake 1 backlash pivot plate 2 adjustment bolt with lock nut 3 backlash pivot plate mounting bolts Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 92: September

    Then torque the mounting fasteners on the backlash pivot plate. Refer to Specifications, Machine Torque Specifications. Rotate the turntable through an entire rotation. Check for tight spots that could cause binding. Readjust if necessary. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 93: Steer Axle Components

    Note: Replace the thrust washer when installing Raise the machine approximately 6 inches / the yoke and drive hub assembly onto the axle. 15 cm and place blocks under the chassis for support. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 94: Drive Motors

    Do not allow oil to squirt or spray. Note: Do not re-use the drive hub mounting fasteners. Genie specifications require the use of new fasteners. Remove the drive motor mounting fasteners. Slide the drive motor shaft out of the drive hub, and remove the drive motor from the machine.

  • Page 95: Steer Cylinders

    Remove the pin retaining fasteners from the steer cylinder pivot pins. Remove the pivot pin from each end of the steer cylinder. Remove the steering cylinder from the machine. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 96: Non-Steer Axle Components

    This procedure is the same as the steer axle This procedure is the same as the steer axle procedure. Refer to Repair Procedure, How to procedure. Refer to Repair Procedure, How to Remove a Drive Hub. Remove a Drive Motor. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 97: Oscillating Axle Components

    Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 98: Oscillate Directional Valve

    12 Turn the engine off, remove the pressure gauge and assemble the directional valve linkage. 13 Install the cover on the non-steer end of the drive chassis. 1 oscillate valve 2 clevis yoke 3 drive chassis S-80 • S-85 • S-80X Part No. 1269074...

  • Page 99: How To Set Up The Directional Valve Linkage

    Confirm whether the drive chassis is completely level. If the drive chassis is not level, start the engine and push up or pull down on the linkage adjustment rod until the machine is completely level. Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 100 Service and Repair Manual September 2015 This page intentionally left blank. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 101: Fault Codes

    • Boom in the stowed position • Turntable secured with the turntable rotation lock • Welder disconnected from the machine (if equipped with the weld cable to platform option) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 102: Control System Fault Codes

    Maintain firm contact with a metal part of the machine that is grounded at all times when handling printed circuit boards OR use a grounded wrist strap. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 103: Control System Fault Codes

    Function is inoperative. Alarm sounds Cycle power off, then on Down. Joystick indicating a fault. after problem has been corrected. Value too high Value too low Value at 0V Not calibrated Calibrate joystick. Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 104 Calibrate valve threshold. one or both directions is zero. Drive Enable Fault Drive enable override direction is Cycle power off, then on Override Switch frozen at neutral. after problem has been corrected. S-80 • S-85 • S-80X Part No. 1269074...
  • Page 105 Frozen at zero and neutral. ALarm problem has been corrected. sounds indicating a fault. Value too low Not calibrated Normal function except threshold Calibrate valve threshold. for one or both directions is zero. Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 106 Not calibrated Calibrate joystick. Steer Directional Fault Limited speed and direction. Cycle power off, then on after Valve Frozen at zero and neutral. Alarm problem has been corrected. sounds indicating a fault. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 107: Fault Code Display - Deutz And Perkins Models

    Note: All faults are stored in the Previous Fault history menu. These faults will not be erased when corrective action has been completed. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 108: Fault Code Display - Flashing And Solid Led's Deutz D 2.9 L4 And Perkins 404F-22 Models

    Flashing with left and right red LED's flashing, engine soot level over 140%. Engine shut down. Contact service. 6 Right red LED: Flashing, engine fault detected. Contact service. Flashing with right flashing amber LED, engine soot level over 140%. Engine shut down. Contact service. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 109: Deutz D 2.9 L4 And Perkins 404F-22 Models

    Regeneration forced • Scroll down • Decrease • Decrease contrast (-) Regeneration inhibited • Select / Next • Main menu • Increase contarst (+) Note: Regeneration, initiate, inhibit and soot only apply to the Perkins 404F-22 models. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 110: Main Menu Structure - Deutz D 2.9 L4 Models

    Service and Repair Manual September 2015 Fault Code Display - Deutz and Perkins Models Main M enu Str ucture - Deutz D 2.9 L4 Models Main Menu Structure - Deutz D 2.9 L4 Models S-80 • S-85 • S-80X Part No. 1269074...

  • Page 111: Main Menu Structure - Perkins 404F-22 Models

    September 2015 Service and Repair Manual Fault Code Display - Deutz and Perkins Models Main M enu Str ucture - Perkins 404F-22 M odels Main Menu Structure - Perkins 404F-22 Models Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 112: Deutz D 2.9 L4 Engine Fault Codes

    Charged air pressure above Overload by short-circuit warning threshold 1016 Actuator position for EGR-Valve Charged air pressure above shut off threshold not plausible Sensor error charged air press.; signal range check low S-80 • S-85 • S-80X Part No. 1269074...
  • Page 113 High oil temperature; shut off drift limit threshold exceeded Sesnor error rail pressure; signal Physical range check low for oil range check high temperature Sensor error rail pressure; signal range check low Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 114 3 (in firing order) Physical range check low for Injector 3 (in firing order); EGR differential pressure interruption of electric connection Sensor error differential pressure Venturiunit (EGR); signal range check low S-80 • S-85 • S-80X Part No. 1269074...
  • Page 115 Setpoint upstream turbine; plausibility 1079 13 Sensor supply voltage monitor error 1 error (ECU) 1188 2 1414 Wastegate; status message from 1080 13 Sensor supply voltage monitor ECU missing 2 error (ECU) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 116 Physical range check high for 2659 2 1523 Exhaust gas recirculation AGS exhaust gas temperature sensor; plausibility error upstream (DOC) 4765 1 1042 Physical range check low for exhaust gas temperature upstream (DOC) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 117 523601 Sensor supply voltage monitor 523009 Pressure relief valve (PRV) 3 error (ECU) reached maximun allowed open 523603 Timeout Error of time CAN-Receive-Frame AMB; Ambient Temperature Sensor Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 118 523619 Physical range check high for 523612 Internal ECU monitoring exhaust gas temperature detection reported error upstrem (SCR-CAT) 523698 Shut off request from supervisory monitoring function S-80 • S-85 • S-80X Part No. 1269074...
  • Page 119 523914 Glow plug control; powerstage 523779 Passive Timeout Error of over temperature CAN-Receive-Frame TSC1TR 523919 1378 Sensor air pump airpressure; plausibility error 523920 1379 Sensor exhaust gas back pressure burner; plausibility error Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 120 523982 Powerstage diagnosis disabled; CAN-Transmit-Frame high battery voltage EEC3VOL2; Engine send 523982 Powerstage diagnosis disabled; messages low battery voltage 523946 1158 Zero fuel calibration injector 1 (in firing order); maximum value exceeded S-80 • S-85 • S-80X Part No. 1269074...
  • Page 121 524101 1667 Timeout error of 524029 1432 Timeout Error of CAN-Transmit-Frame CAN-Receive-Frame ComDPFTstMon ComEGRActr - exhaust gas recirculation positioner 524030 1440 EGR actuator; internal error 524031 1441 EGR actuator; calibration error Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 122 CAN-Transmit-Frame ComTxAT1IMG ComETVActr 524125 9 1687 Timeout error of 524111 9 1680 Timeout error of CAN-Receive-Frame CAN-Receive-Frame ComTxTrbChActr ComRxETVActr 524112 9 1671 Timeout ComITVActr 524113 9 1681 Timeout error of CAN-Receive-Frame ComRxITVActr S-80 • S-85 • S-80X Part No. 1269074...

  • Page 123: Perkins 404F-22 Engine Fault Codes

    Particulate Trap Intake Gas Temp: Voltage Below Normal High - least severe(1)" Engine Fuel Rack Actuator: Current 3242 Particulate Trap Intake Gas Temp: Above Normal High-moderate severity (2) J1939 Network#1: Special Instruction Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 124 Percent: High- most severe (3) 3719 Particulate Trap #1 Soot Load Percent: High-moderate severity (2) 4016 High Current Auxiliary Power Relay 1: Current Above Normal 4201 Engine Speed Sensor #1: Voltage Above Normal S-80 • S-85 • S-80X Part No. 1269074...

  • Page 125: Continental Tme27 Engine Fault Codes

    1654 three times. After the fault codes, the check engine light will blink a code 1654 three times again indicating the end of the stored codes. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 126: Continental Tme27 Engine Fault Codes

    TPS1/2 voltage fault detection above 1 = Shutdown 2 = AL disable 3 = AL disable key-cycle 4 = Power derate 1 5 = Power derate 2 6 = Low rev limit S-80 • S-85 • S-80X Part No. 1269074...

  • Page 127: September

    EGO2 RMS > CL waveform RMS* 50% 1 = Shutdown 2 = AL disable 3 = AL disable key-cycle 4 = Power derate 1 5 = Power derate 2 6 = Low rev limit Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 128 EGO2 RMS > CL waveform RMS* 50% 1 = Shutdown 2 = AL disable 3 = AL disable key-cycle 4 = Power derate 1 5 = Power derate 2 6 = Low rev limit S-80 • S-85 • S-80X Part No. 1269074...
  • Page 129 EPR Internal Comm fault detection 1 = Shutdown 2 = AL disable 3 = AL disable key-cycle 4 = Power derate 1 5 = Power derate 2 6 = Low rev limit Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 130 Address conflict counter > 5 Failure 1 = Shutdown 2 = AL disable 3 = AL disable key-cycle 4 = Power derate 1 5 = Power derate 2 6 = Low rev limit S-80 • S-85 • S-80X Part No. 1269074...

  • Page 131: Schematics

    Read, understand and obey the safety rules and operating instructions in the appropriate operator's manual on your machine.  Be sure that all necessary tools and test equipment are available and ready for use. Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 132: Electrical Symbol Legend

    Oil temperature switch Coolant temperature Oil pressure switch Control relay contact Diode starting aid, glow normally open switch - normally open normally closed normally open plug or flame ignitor S-80 • S-85 • S-80X Part No. 1269074...

  • Page 133: Hydraulic Symbols Legend

    3 way shuttle valve valve Solenoid operated Counterbalance valve with Pilot operated 2 position, 2 position, 2 way solenoid 3 position 4 way directional pressure and pilot ratio 2 way directional valve valve valve Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 134: Relay And Fuse Panel Legend - Deutz Td2011L04I

    Relay and F use Panel Legend - Perkins 404F-22T Perkins 404F-22T Label Description CR4A LOW RPM RELAY CR4B HIGH RPM RELAY HORN RELAY CR17 HYDRAULIC OIL COOLER RELAY CR39 AUXILIARY PUMP RELAY FUSE, 20A, B1BAT, P116PWR FUSE, 20A, B1BAT, P24PWR S-80 • S-85 • S-80X Part No. 1269074...

  • Page 135: Relay And Fuse Panel Legend - Perkins 804D-33

    IGNITION / FUEL RELAY HORN RELAY CR17 HYDRAULIC OIL COOLER RELAY CR39A AUXILIARY PUMP RELAY CR39B AUXILIARY PUMP ENGINE CUTOUT RELAY FUSE, 30A, OIL COOLER FAN / HORN FUSE, 30A, ENGINE / AUXILIARY PUMP Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 136: Connector Pin Legends

    OR/RD C42LS OR/RD C17PRL C46HRN C18PRR GR/BK P134PWR GR/BK C43JU GR/WH C45GEN GR/WH C44JD RD/OR C123PBS GR/RD C49DLITE OR/GR P109ANG OR/WH SPARE LT BR SNSR GND LT BR PLUG PLUG PLUG PLUG S-80 • S-85 • S-80X Part No. 1269074...
  • Page 137 C177LS BL/RD (S-80X) C14PLU C42LS OR/RD C15PLD OR/BK P134PWR(A) P134PWR(B) P134PWR(C) C28TTA RD/BK C211LO BL/BK (S-80X) C118LSR C123PBS RD/BK SNSR GND P109ANG GR/WH C36STC C37STCC BL/BK C212LO GR/BK (S-80X) C45GEN GR/WH C40LS Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 138 C37STCC BL/BK JSGND2 C32BRK WH/RD P162JPW1 C29MS RD/WH JSGND1 J8 S-80X Model C28TTA RD/BK Pin # Circuit # Color C13DRE(A) BL/RD P109LS GR/WH C184PL C169LED2 P109LS GR/WH C177LS BL/RD SNSR GND C169LED1 S-80 • S-85 • S-80X Part No. 1269074...
  • Page 139 WH(14) Engine Plug - Continental TME27 Pin # Circuit # Color R23PWR C21RET C38RET C38FP BL/WH R33STR BK(14) C41RPM OR/BK R21IGN C35RPM BK/RD C108ESL BL/WH C127TSW C39LP BL/RD C26TSR WH/RD Gauge Option Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 140 BK/RD V155PCE OR/RD V155PCE OR/RD V155PCE OR/RD C31EDC- WH/BK C31EDC- WH/BK C31EDC- WH/BK C30EDC+ C30EDC+ C30EDC+ C34SA BK/WH C34SA BK/WH C32BRK WH/RD C32BRK WH/RD C32BRK WH/RD C29MS RD/WH C29MS RD/WH C29MS RD/WH S-80 • S-85 • S-80X Part No. 1269074...

  • Page 141: Continental Tme27 Engine Harness

    September 2015 Service and Repair Manual Continental TME27 Engine Harness...
  • Page 142 Service and Repair Manual September 2015 Continental TME27 Engi ne H arness Continental TME27 Engine Harness S-80 • S-85 • S-80X Part No. 1269074...

  • Page 143: S-80X Ground Control Box Wiring Diagram

    September 2015 Service and Repair Manual S-80X Ground Contr ol Box Wiring Di agr am S-80X Ground Control Box Wiring Diagram Use this wiring diagram with each S-80X Ground Control Box Schematic Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 144 Service and Repair Manual September 2015 S-80X Ground Control Box Wiring Diagram...

  • Page 145: Deutz Td2.9 L4 Engine Harness

    September 2015 Service and Repair Manual Deutz TD2.9 L4 Engine Harness...
  • Page 146 Service and Repair Manual September 2015 Deutz TD 2.9 L4 Engi ne H arness Deutz TD2.9 L4 Engine Harness S-80 • S-85 • S-80X Part No. 1269074...

  • Page 147: Perkins 404F-22T Engine Harness

    September 2015 Service and Repair Manual Perki ns 404F-22T Engi ne Har ness Perkins 404F-22T Engine Harness Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 148 Service and Repair Manual September 2015 Perkins 404F-22T Engine Harness...

  • Page 149: Electrical Schematic, S-80X - Deutz Td2.9 L4 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematics, S-80X – ANSI and C SA Mod els Electrical Schematic, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
  • Page 150 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80X - D eutz TD 2.9 L4 Models (AN SI / C SA) Electrical Schematic, S-80X Deutz TD2.9 L4 Models (ANSI / CSA) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 151 September 2015 Service and Repair Manual Electrical Schematic, S-80X Deutz TD2.9 L4 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 152 Service and Repair Manual September 2015 Electrical Schematic, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)

  • Page 153: Ground Control Box, S-80X - Deutz Td2.9 L4 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
  • Page 154 Ground C ontrol Box, S-80X - Deutz TD 2.9 L4 M odels (AN SI / CSA) Ground Control Box, S-80X Deutz TD2.9 L4 Models (ANSI / CSA) Refer to S-80X Ground Control Box Wiring Diagram for additional wiring. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 155: Platform Control Box, S-80X Deutz Td2.9 L4 Models (Ansi / Csa)

    Service and Repair Manual Platform C ontrol Box, S-80X - D eutz TD 2.9 L4 Models (AN SI / C SA) Platform Control Box, S-80X Deutz TD2.9 L4 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 156 Service and Repair Manual September 2015 Platform Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)

  • Page 157: Electrical Schematic, S-80X - Deutz Td2011L04I Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematic, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
  • Page 158 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80X - D eutz TD 2011L04i M odels (ANSI / C SA) Electrical Schematic, S-80X Deutz TD2011L04i Models (ANSI / CSA) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 159 September 2015 Service and Repair Manual Electrical Schematic, S-80X Deutz TD2011L04i Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 160 Service and Repair Manual September 2015 Electrical Schematic, S-80X - Deutz TD2011L04i Models (ANSI / CSA)

  • Page 161: Ground Control Box, S-80X - Deutz Td2011L04I Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
  • Page 162 Ground C ontrol Box, S-80X - Deutz TD 2011L04i Models (AN SI / C SA) Ground Control Box, S-80X Deutz TD2011L04i Models (ANSI / CSA) Refer to S-80X Ground Control Box Wiring Diagram for additional wiring. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 163: Platform Control Box, S-80X Deutz Td2011L04I Models (Ansi / Csa)

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80X - D eutz TD 2011L04i Models (AN SI / C SA) Platform Control Box, S-80X Deutz TD2011L04i Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 164 Service and Repair Manual September 2015 Platform Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)

  • Page 165: Electrical Schematic, S-80X - Perkins 404F-22T Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematic, S-80X - Perkins 404F-22T Models (ANSI / CSA)
  • Page 166 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80X - Perki ns 404F- 22T Models (AN SI / C SA) Electrical Schematic, S-80X Perkins 404F-22T Models (ANSI / CSA) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 167 September 2015 Service and Repair Manual Electrical Schematic, S-80X Perkins 404F-22T Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 168 Service and Repair Manual September 2015 Electrical Schematic, S-80X - Perkins 404F-22T Models (ANSI / CSA)

  • Page 169: Ground Control Box, S-80X - Perkins 404F-22T Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
  • Page 170 Ground C ontrol Box, S-80X - Perkins 404F-22T M odels (ANSI / CSA) Ground Control Box, S-80X Perkins 404F-22T Models (ANSI / CSA) Refer to S-80X Ground Control Box Wiring Diagram for additional wiring. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 171: Platform Control Box, S-80X Perkins 404F-22T Models (Ansi / Csa)

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80X - Perki ns 404F- 22T Models (AN SI / CSA) Platform Control Box, S-80X Perkins 404F-22T Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 172 Service and Repair Manual September 2015 Platform Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)

  • Page 173: Electrical Schematic, S-80X - Perkins 804D-33 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematic, S-80X - Perkins 804D-33 Models (ANSI / CSA)
  • Page 174 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80X - Perki ns 804D- 33 Models (AN SI / CSA) Electrical Schematic, S-80X Perkins 804D-33 Models (ANSI / CSA) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 175 September 2015 Service and Repair Manual Electrical Schematic, S-80X Perkins 804D-33 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 176 Service and Repair Manual September 2015 Electrical Schematic, S-80X - Perkins 804D-33 Models (ANSI / CSA)

  • Page 177: Ground Control Box, S-80X - Perkins 804D-33 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
  • Page 178 Ground C ontrol Box, S-80X - Perkins 804D-33 M odels ( ANSI / CSA) Ground Control Box, S-80X Perkins 804D-33 Models (ANSI / CSA) Refer to S-80X Ground Control Box Wiring Diagram for additional wiring. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 179: Platform Control Box, S-80X Perkins 804D-33 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80X - Perki ns 804D-33 M odels (ANSI / CSA) Platform Control Box, S-80X Perkins 804D-33 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 180 Service and Repair Manual September 2015 Platform Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)

  • Page 181: Electrical Schematic, S-80X - Continental Tme27 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematic, S-80X - Continental TME27 Models (ANSI / CSA)
  • Page 182 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80X - C ontinental TME27 Models (AN SI / C SA) Electrical Schematic, S-80X Continental TME27 Models (ANSI / CSA) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 183 September 2015 Service and Repair Manual Electrical Schematic, S-80X Continental TME27 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 184 Service and Repair Manual September 2015 Electrical Schematic, S-80X - Continental TME27 Models (ANSI / CSA)

  • Page 185: Ground Control Box, S-80X - Continental Tme27 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
  • Page 186 Ground C ontrol Box, S-80X - Conti nental TM E27 M odels (AN SI / CSA) Ground Control Box, S-80X Continental TME27 Models (ANSI / CSA) Refer to S-80X Ground Control Box Wiring Diagram for additional wiring. S-80 • S-85 • S-80X Part No. 1269074...

  • Page 187: Platform Control Box, S-80X Continental Tme27 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80X - C ontinental TME27 Models (AN SI / C SA) Platform Control Box, S-80X Continental TME27 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 188: September

    Service and Repair Manual September 2015 Platform Control Box, S-80X - Continental TME27 Models (ANSI / CSA)

  • Page 189: Electrical Schematic, S-80 • S-85 - Deutz Td2.9 L4 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematics, S-80, S- 85 – AN SI and CSA Models Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (ANSI / CSA)

  • Page 190: Deutz Td2.9 L4 Models (Ansi / Csa)

    Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Deutz TD 2.9 L4 M odels (AN SI / CSA) Electrical Schematic, S-80 • S-85 Deutz TD2.9 L4 Models (ANSI / CSA) S-80 • S-85 • S-80X...
  • Page 191 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Deutz TD2.9 L4 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 192 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (ANSI / CSA)

  • Page 193: Ground Control Box, S-80 • S-85 - Deutz Td2.9 L4 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (ANSI / CSA)
  • Page 194 Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - D eutz TD2.9 L4 M odels ( ANSI / C SA) Ground Control Box, S-80 • S-85 Deutz TD2.9 L4 Models (ANSI / CSA) S-80 • S-85 • S-80X...

  • Page 195: Platform Control Box, S-80 • S

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Deutz TD2.9 L4 M odels ( ANSI / CSA) Platform Control Box, S-80 • S-85 Deutz TD2.9 L4 Models (ANSI / CSA) Part No. 1269074...

  • Page 196: Platform Control Box, S-80 • S-85 - Deutz Td2.9 L4 Models (Ansi / Csa)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (ANSI / CSA)

  • Page 197: Electrical Schematic, S-80 • S-85 - Deutz Td2011L04I Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (ANSI / CSA)
  • Page 198 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Deutz TD 2011L04i Models (AN SI / CSA) Electrical Schematic, S-80 • S-85 Deutz TD2011L04i Models (ANSI / CSA) S-80 • S-85 • S-80X...
  • Page 199 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Deutz TD2011L04i Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 200 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (ANSI / CSA)

  • Page 201: Ground Control Box, S-80 • S-85 - Deutz Td2011L04I Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (ANSI / CSA)

  • Page 202: Deutz Td2011L04I Models (Ansi / Csa)

    Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - D eutz TD2011L04i M odels ( ANSI / CSA) Ground Control Box, S-80 • S-85 Deutz TD2011L04i Models (ANSI / CSA) S-80 • S-85 • S-80X...

  • Page 203: Platform Control Box, S-80 • S

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Deutz TD2011L04i M odels (ANSI / CSA) Platform Control Box, S-80 • S-85 Deutz TD2011L04i Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 204: Platform Control Box, S-80 • S-85 - Deutz Td2011L04I Models (Ansi / Csa)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (ANSI / CSA)

  • Page 205: Electrical Schematic, S-80 • S-85 - Perkins 404F-22T Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Perkins 404F-22T Models (ANSI / CSA)
  • Page 206 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Perkins 404F-22T M odels ( ANSI / CSA) Electrical Schematic, S-80 • S-85 Perkins 404F-22T Models (ANSI / CSA) S-80 • S-85 • S-80X...
  • Page 207 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Perkins 404F-22T Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 208 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Perkins 404F-22T Models (ANSI / CSA)

  • Page 209: Ground Control Box, S-80 • S-85 - Perkins 404F-22T Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Perkins 404F-22T Models (ANSI / CSA)

  • Page 210: Perkins 404F-22T Models (Ansi / Csa)

    Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - Perkins 404F- 22T M odels (AN SI / C SA) Ground Control Box, S-80 • S-85 Perkins 404F-22T Models (ANSI / CSA) S-80 • S-85 • S-80X...

  • Page 211: Platform Control Box, S-80 • S

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Perkins 404F-22T M odels ( ANSI / CSA) Platform Control Box, S-80 • S-85 Perkins 404F-22T Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 212 Service and Repair Manual September 2015 Platform Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)

  • Page 213: Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (ANSI / CSA)
  • Page 214 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Perkins 804D-33 M odels ( ANSI / CSA) Electrical Schematic, S-80 • S-85 Perkins 804D-33 Models (ANSI / CSA) S-80 • S-85 • S-80X...
  • Page 215 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Perkins 804D-33 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 216 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (ANSI / CSA)

  • Page 217: Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (ANSI / CSA)

  • Page 218: Perkins 804D-33 Models (Ansi / Csa)

    Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - Perkins 804D- 33 Models (AN SI / C SA) Ground Control Box, S-80 • S-85 Perkins 804D-33 Models (ANSI / CSA) S-80 • S-85 • S-80X...

  • Page 219: Platform Control Box, S-80 • S

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Perkins 804D-33 M odels ( ANSI / C SA) Platform Control Box, S-80 • S-85 Perkins 804D-33 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 220: Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (Ansi / Csa)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (ANSI / CSA)

  • Page 221: Electrical Schematic, S-80 • S-85 - Continental Tme27 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Continental TME27 Models (ANSI / CSA)

  • Page 222: Continental Tme27 Models (Ansi / Csa)

    Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Conti nental TM E27 M odels (ANSI / CSA) Electrical Schematic, S-80 • S-85 Continental TME27 Models (ANSI / CSA) S-80 • S-85 • S-80X...
  • Page 223 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Continental TME27 Models (ANSI / CSA) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 224 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Continental TME27 Models (ANSI / CSA)

  • Page 225: Ground Control Box, S-80 • S-85 - Continental Tme27 Models (Ansi / Csa)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Continental TME27 Models (ANSI / CSA)
  • Page 226 Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - C ontinental TME27 M odels ( ANSI / C SA) Ground Control Box, S-80 • S-85 Continental TME27 Models (ANSI / CSA) S-80 • S-85 • S-80X...

  • Page 227: Platform Control Box, S-80 • S

    September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Conti nental TM E27 M odels ( ANSI / CSA) Platform Control Box, S-80 • S-85 Continental TME27 Models (ANSI / CSA) Part No. 1269074...

  • Page 228: Platform Control Box, S-80 • S-85 - Continental Tme27 Models (Ansi / Csa)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Continental TME27 Models (ANSI / CSA)

  • Page 229: Electrical Schematic, S-80 • S-85 - Deutz Td2.9 L4 Models (Ce)

    September 2015 Service and Repair Manual Electrical Schematics, S-80, S- 85 – C E Mod els Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)

  • Page 230: Electrical Schematic, S-80 • S-85 - Deutz Td2011L04I Models (Ce)

    Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Deutz TD 2.9 L4 M odels (CE) Electrical Schematic, S-80 • S-85 Deutz TD2.9 L4 Models (CE) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 231 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Deutz TD2.9 L4 Models (CE) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 232 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)

  • Page 233: Ground Control Box, S-80 • S-85 - Deutz Td2011L04I Models (Ce)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)

  • Page 234: Ground Control Box, S-80 • S-85 - Deutz Td2.9 L4 Models (Ce)

    Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - D eutz TD2.9 L4 M odels (C E) Ground Control Box, S-80 • S-85 Deutz TD2.9 L4 Models (CE) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 235 September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Deutz TD2.9 L4 M odels (C E) Platform Control Box, S-80 • S-85 Deutz TD2.9 L4 Models (CE) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 236: Platform Control Box, S-80 • S-85 - Deutz Td2011L04I Models (Ce)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
  • Page 237 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (CE)
  • Page 238 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Deutz TD 2011L04i Models (CE) Electrical Schematic, S-80 • S-85 Deutz TD2011L04i Models (CE) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 239 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Deutz TD2011L04i Models (CE) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 240 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (CE)
  • Page 241 September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
  • Page 242 Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - D eutz TD2011L04i M odels (C E) Ground Control Box, S-80 • S-85 Deutz TD2011L04i Models (CE) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 243 September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Deutz TD2011L04i M odels (CE) Platform Control Box, S-80 • S-85 Deutz TD2011L04i Models (CE) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 244 Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)

  • Page 245: Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (Ce)

    September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (CE)
  • Page 246 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Perkins 804D-33 M odels (C E) Electrical Schematic, S-80 • S-85 Perkins 804D-33 Models (CE) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 247 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Perkins 804D-33 Models (CE) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 248 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (CE)

  • Page 249: Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (Ce)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
  • Page 250 Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - Perkins 804D- 33 Models (CE) Ground Control Box, S-80 • S-85 Perkins 804D-33 Models (CE) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 251 September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Perkins 804D-33 M odels (C E) Platform Control Box, S-80 • S-85 Perkins 804D-33 Models (CE) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 252: Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (Ce)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)

  • Page 253: Electrical Schematic, S-80 • S-85 - Continental Tme27 Models (Ce)

    September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Continental TME27 Models (CE)
  • Page 254 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Conti nental TM E27 M odels (CE) Electrical Schematic, S-80 • S-85 Continental TME27 Models (CE) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 255 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Continental TME27 Models (CE) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 256 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Continental TME27 Models (CE)

  • Page 257: Ground Control Box, S-80 • S-85 - Continental Tme27 Models (Ce)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Continental TME27 Models (CE)
  • Page 258 Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - C ontinental TME27 M odels (C E) Ground Control Box, S-80 • S-85 Continental TME27 Models (CE) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 259 September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Conti nental TM E27 M odels (C E) Platform Control Box, S-80 • S-85 Continental TME27 Models (CE) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 260: Platform Control Box, S-80 • S-85 - Continental Tme27 Models (Ce)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Continental TME27 Models (CE)

  • Page 261: Electrical Schematic, S-80 • S-85 - Deutz Td2011L04I Models (As)

    September 2015 Service and Repair Manual Electrical Schematics, S-80, S- 85 – A S Mod els Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (AS)
  • Page 262 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Deutz TD 2011L04i Models (AS) Electrical Schematic, S-80 • S-85 Deutz TD2011L04i Models (AS) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 263 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Deutz TD2011L04i Models (AS) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 264 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (AS)

  • Page 265: Ground Control Box, S-80 • S-85 - Deutz Td2011L04I Models (As)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
  • Page 266 Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - D eutz TD2011L04i M odels ( AS) Ground Control Box, S-80 • S-85 Deutz TD2011L04i Models (AS) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 267 September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Deutz TD2011L04i M odels (AS) Platform Control Box, S-80 • S-85 Deutz TD2011L04i Models (AS) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 268: Platform Control Box, S-80 • S-85 - Deutz Td2011L04I Models (As)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)

  • Page 269: Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (As)

    September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (AS)
  • Page 270 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Perkins 804D-33 M odels ( AS) Electrical Schematic, S-80 • S-85 Perkins 804D-33 Models (AS) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 271 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Perkins 804D-33 Models (AS) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 272 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (AS)

  • Page 273: Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (As)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
  • Page 274 Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - Perkins 804D- 33 Models (AS) Ground Control Box, S-80 • S-85 Perkins 804D-33 Models (AS) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 275 September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Perkins 804D-33 M odels ( AS) Platform Control Box, S-80 • S-85 Perkins 804D-33 Models (AS) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 276: Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (As)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)

  • Page 277: Electrical Schematic, S-80 • S-85 - Continental Tme27 Models (As)

    September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 - Continental TME27 Models (AS)
  • Page 278 Service and Repair Manual September 2015 Elec trical Schem atic, S- 80 • S- 85 - Conti nental TM E27 M odels (AS) Electrical Schematic, S-80 • S-85 Continental TME27 Models (AS) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 279 September 2015 Service and Repair Manual Electrical Schematic, S-80 • S-85 Continental TME27 Models (AS) Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 280 Service and Repair Manual September 2015 Electrical Schematic, S-80 • S-85 - Continental TME27 Models (AS)

  • Page 281: Ground Control Box, S-80 • S-85 - Continental Tme27 Models (As)

    September 2015 Service and Repair Manual Ground Control Box, S-80 • S-85 - Continental TME27 Models (AS)
  • Page 282 Service and Repair Manual September 2015 Ground C ontrol Box, S-80 • S-85 - C ontinental TME27 M odels ( AS) Ground Control Box, S-80 • S-85 Continental TME27 Models (AS) S-80 • S-85 • S-80X Part No. 1269074...
  • Page 283 September 2015 Service and Repair Manual Platform C ontrol Box, S-80 • S- 85 - Conti nental TM E27 M odels ( AS) Platform Control Box, S-80 • S-85 Continental TME27 Models (AS) Part No. 1269074 S-80 • S-85 • S-80X...

  • Page 284: Platform Control Box, S-80 • S-85 - Continental Tme27 Models (As)

    Service and Repair Manual September 2015 Platform Control Box, S-80 • S-85 - Continental TME27 Models (AS)

  • Page 285: Continental Options Schematic

    September 2015 Service and Repair Manual Sch em atics - Optio ns Continental Options Schematic...
  • Page 286 Service and Repair Manual September 2015 Continental Options Sc hem atic Continental Options Schematic S-80 • S-85 • S-80X Part No. 1269074...

  • Page 287: Deutz And Perkins Options Schematic

    September 2015 Service and Repair Manual Deutz and Perki ns Options Sc hem atic Deutz and Perkins Options Schematic Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 288 Service and Repair Manual September 2015 Deutz and Perkins Options Schematic...

  • Page 289: Platform Level Cutout, Cte Option

    September 2015 Service and Repair Manual Platform Level Cutout, CTE Option...
  • Page 290 Service and Repair Manual September 2015 Platform Level Cutout, CTE Opti on Platform Level Cutout, CTE Option S-80 • S-85 • S-80X Part No. 1269074...

  • Page 291: 12 Kw Hydraulic Generator Wiring Diagram

    September 2015 Service and Repair Manual 12 kW Hy draulic Gener ator Wiring Diagram 12 kW Hydraulic Generator Wiring Diagram Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 292 Service and Repair Manual September 2015 12 kW Hydraulic Generator Wiring Diagram...

  • Page 293: 12 Kw Hydraulic Generator Electrical Schematic

    September 2015 Service and Repair Manual 12 kW Hydraulic Generator Electrical Schematic...
  • Page 294 Service and Repair Manual September 2015 12 kW Hy draulic Gener ator El ectric al Schematic 12 kW Hydraulic Generator Electrical Schematic S-80 • S-85 • S-80X Part No. 1269074...

  • Page 295: Belt Driven Generator Option

    September 2015 Service and Repair Manual Belt Driven Gener ator Opti on Belt Driven Generator Option Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 296 Service and Repair Manual September 2015 Belt Driven Generator Option...

  • Page 297: Hydraulic Schematic, 2Wd Models

    September 2015 Service and Repair Manual Hydr aulic Schematics Hydraulic Schematic, 2WD Models...
  • Page 298 Service and Repair Manual September 2015 Hydraulic Schem atic, 2WD M odels Hydraulic Schematic, 2WD Models S-80 • S-85 • S-80X Part No. 1269074...

  • Page 299: Hydraulic Schematic, 4Wd Models

    September 2015 Service and Repair Manual Hydraulic Schem atic, 4WD M odels Hydraulic Schematic, 4WD Models Part No. 1269074 S-80 • S-85 • S-80X...
  • Page 300 Service and Repair Manual September 2015 Hydraulic Schematic, 4WD Models S-80 • S-85 • S-80X Part No. 1269074 Servic e and R epair M anual Sept emb er 2015...

This manual is also suitable for:

S-85S-80x

Table of Contents

Save PDF