Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
mDe18mNay/mNaZ/Csay/CsaZ/PDay/PDaZ/Pray/PraZ
INSTRUCTIONS D'INSTALLATION
s
éCheuse à usaGe CommerCial
mDe18mNay/mNaZ/Csay/CsaZ/PDay/PDaZ/Pray/PraZ
TABLE OF CONTENTS
Dryer Safety .......................................................................................................... 2
Tools & Parts ....................................................................................................... 5
Dimensions/Clearances .............................................................................. 6
Gas Dryer Installation Requirements ................................................... 7
Electric Dryer Installation Requirements ......................................... 10
Dryer Venting Requirements .................................................................. 13
Gas Supply Connection ............................................................................ 15
Installing Leveling Legs, Coin Slide, and Coin Box ..................... 17
Electric Dryer Electrical Connections ................................................ 18
Leveling .............................................................................................................. 22
Complete Installation .................................................................................. 23
Reversing Dryer Door Swing ................................................................... 24
Changing to a 30- or 60-Minute Timing Cam ................................. 25
Maintenance Instructions ......................................................................... 26
If You Need Assistance .............................................................................. 26
Electronic Control Setup Instructions ............................................... 27
W10474273A
W10474274A - SP
C
D
ommerCial
ryer
m
mDG18CsaW/mNaW/PDaW/PDaX/PraW
oDels
m
mDG18CsaW/mNaW/PDaW/PDaX/PraW
oDèles
Page
G
e
as or
leCtriC
à
GaZ ou éleCtrique
TABLE DES MATIÈRES
Sécurité de la sécheuse .......................................................................... 32
Outils et pièces ........................................................................................... 35
Dimensions/Distances de dégagement ........................................ 36
Exigences d'installation pour la sécheuse à gaz ........................ 37
Exigences d'installation pour
la sécheuse électrique ........................................................................... 40
Exigences concernant l'évacuation
de la sécheuse ............................................................................................ 42
Raccordement à la canalisation de gaz ......................................... 44
Installation des pieds de nivellement, de la glissière
à monnaie et de la caisse à monnaie .............................................. 46
Nivellement .....................................................................................................47
Achever l'installation ..................................................................................48
Inversion du sens d'ouverture de la porte ......................................49
Installation d'une came de minutage
de 30 ou 60 minutes ..................................................................................50
Instructions d'entretien .............................................................................51
Si vous avez besoin d'assistance .......................................................51
Instructions de réglage du tableau
de commande électronique .................................................................. 52
www.maytagcommerciallaundry.com
Page
Advertisement
Table of Contents
Related Manuals for Maytag MDG18CMNAW
Summary of Contents for Maytag MDG18CMNAW
-
Page 1: Table Of Contents
INSTALLATION INSTRUCTIONS ommerCial ryer as or leCtriC mDG18CsaW/mNaW/PDaW/PDaX/PraW oDels mDe18mNay/mNaZ/Csay/CsaZ/PDay/PDaZ/Pray/PraZ INSTRUCTIONS D’INSTALLATION à éCheuse à usaGe CommerCial GaZ ou éleCtrique mDG18CsaW/mNaW/PDaW/PDaX/PraW oDèles mDe18mNay/mNaZ/Csay/CsaZ/PDay/PDaZ/Pray/PraZ TABLE OF CONTENTS TABLE DES MATIÈRES Page Page Dryer Safety ......................2 Sécurité de la sécheuse ................32 Tools &... -
Page 2: Dryer Safety
DRYER SAFETY It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer smells ■ gas. This information should be obtained from your gas supplier. Post the following warning in a prominent location. ■... - Page 3 DRYER SAFETY IMPORTANT: When discarding or storing your old clothes dryer, remove the door.
-
Page 4: Important Safety Instructions
DRYER SAFETY IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions, including the following: Read all instructions before using the dryer. Clean dryer lint screen before or after each load. ■... -
Page 5: Tools & Parts
TOOLS & PARTS Tools Needed: 8" (203 mm) 8" (203 mm) or 10" (254 mm) Flat-Blade Screwdriver Phillips Screwdriver or 10" (254 mm) Adjustable Wrench Pipe Wrench that opens to 1" (25 mm) Torx T-20 Security 1" (25 mm) Hex-Head 5⁄16"... -
Page 6: Dimensions/Clearances
DIMENSIONS/CLEARANCES Dimensions Side View Back View " 27" (743 mm) (686 mm) " Electric (648 mm) " " (343 mm) (210 mm) 35" " (889 mm) (1048 mm) 11" (electric models) (279 mm) " 37" (38 mm) (940 mm) 4" dia (gas models) (102 mm) 35"... -
Page 7: Gas Dryer Installation Requirements
GAS DRYER INSTALLATION REQUIREMENTS Location Requirements Recessed Area and Closet Installation Instructions This dryer may be installed in a recessed area or closet. For recessed area and closet installations, minimum clearances can be found on the warning label on the rear of the dryer or in “Dimensions/Clearances. -
Page 8: Electrical Requirements
GAS DRYER INSTALLATION REQUIREMENTS Electrical Requirements Gas Dryer Grounding IMPORTANT: The dryer must be electrically grounded in accordance with local codes and ordinances or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, latest edition, or Canadian Electrical Code, CSA C22.1. If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate. - Page 9 GAS DRYER INSTALLATION REQUIREMENTS Gas Supply IMPORTANT: Observe all governing codes and ordinances. This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.
-
Page 10: Electric Dryer Installation Requirements
ELECTRIC DRYER INSTALLATION REQUIREMENTS Location Requirements The dryer must be exhausted outdoors. 48 in. (310 cm 3" (76 mm) Front Closet Front Closet View Door View door Your dryer can be installed in a basement, laundry room, or 3" recessed area. (76 mm) 24 in. - Page 11 ELECTRIC DRYER INSTALLATION REQUIREMENTS Electrical Requirements – U.S.A. only (cont.) Electrical Connection Electric Dryer Power Supply Cord To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. This dryer is manufactured ready to install with a 3-wire ■...
-
Page 12: Grounding Instructions
ELECTRIC DRYER INSTALLATION REQUIREMENTS Direct Wire If connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire) and be: Flexible armored cable or nonmetallic sheathed copper cable ■ (with ground wire), covered with flexible metallic conduit. All current-carrying wires must be insulated. -
Page 13: Dryer Venting Requirements
DRYER VENTING REQUIREMENTS Elbows: 45° elbows provide better airflow than 90° elbows. ■ Better Good Clamps: Use clamps to seal all joints. ■ Exhaust vent must not be connected or secured with screws ■ WARNING: To reduce the risk of fire, this dryer MUST BE or other fastening devices that extend into interior of duct and EXHAUSTED OUTDOORS. - Page 14 DRYER VENTING REQUIREMENTS Vent Hoods 4" (102 mm) Diameter Exhaust Hoods Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks, bushes, or snow). Box Hood Louvered Hood Angled Hood...
-
Page 15: Gas Supply Connection
DRYER VENTING REQUIREMENTS If an Exhaust Hood Cannot be Used Multiple Dryer Venting The outside end of main vent should have a sweep elbow directed A main vent can be used for venting a group of dryers. The main downward. vent should be sized to remove 5663 l/min. - Page 16 GAS SUPPLY CONNECTION Type of Gas This dryer is equipped for use with natural gas. It is design-certified by CSA International for LP (propane and butane) gases with appropriate conversion. No attempt shall be made to convert dryer from gas specified on serial/rating plate for use with a different gas without consulting the serving gas supplier.
-
Page 17: Installing Leveling Legs, Coin Slide, And Coin Box
INSTALLING LEVELING LEGS, COIN SLIDE, AND COIN BOX On some models: The console houses the electronic control On some models: The meter case houses the factory-installed board. The board is factory set for a dry time of 45 minutes. accumulator timer with actuating arm or service switch. Consult the tech sheet found inside the dryer toe panel to reset dry The factory-installed timer is set to provide 45 minutes (4 pins) time and for other options. -
Page 18: Electric Dryer Electrical Connections
ELECTRIC DRYER ELECTRICAL CONNECTIONS (FOR U.S.A. ONLY) Strain Relief Remove Terminal Block Cover Power Supply Cord Strain Relief 1. Insert strain relief. 2. Insert power cord into strain relief. (appearance may vary) Strain Relief Direct Wire Strain Relief 1. Insert strain relief. 2. - Page 19 ELECTRIC DRYER ELECTRICAL CONNECTIONS (FOR U.S.A. ONLY) Connection Options Power Cord Direct Wire 4-wire receptacle (NEMA Type 14-30R) 4-wire direct 3-wire receptacle (NEMA Type 10-30R) 3-wire direct Connecting 4-Wire Connection: Power Supply Cord IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.
- Page 20 ELECTRIC DRYER ELECTRICAL CONNECTIONS (FOR U.S.A. ONLY) Connecting 3-Wire Connection: Power Supply Cord Standard Power Cord Connectors 2. Connect neutral wire (white or center wire) (D) of power supply cord under center terminal block screw (A). Tighten screw. Flanged Spade Connector Ring Connector Connecting Neutral Wire 1.
- Page 21 ELECTRIC DRYER ELECTRICAL CONNECTIONS (FOR U.S.A. ONLY) Connecting 4-Wire Connection: Direct Wire Connecting Neutral Ground and Neutral Wires (cont.) Connecting Remaining Wires 2. Connect neutral ground wire (B) and place hooked end (hook 4. Connect remaining wires under outer terminal block screws facing right) of neutral wire (white or center wire) (D) of direct (F).
-
Page 22: Leveling
ELECTRIC DRYER ELECTRICAL CONNECTIONS (FOR U.S.A. ONLY) Connecting 3-Wire Connection: Optional Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire. Connecting Neutral Wire 1. Remove center terminal block screw (A). Also remove neutral 3. -
Page 23: Complete Installation
LEVELING 3. If dryer is not level, use a 1" or 25 mm open-end or adjustable 2. Grip dryer from top and rock back and forth, making sure all four wrench to turn the leveling leg counterclockwise to lower the legs are firmly on floor. -
Page 24: Reversing Dryer Door Swing
REVERSING DRYER DOOR SWING (OPTIONAL) You can change your door swing from a right-side opening 7. Be certain to keep cardboard spacer centered between doors. to left-side opening, if desired. Reattach outer door panel to inner door panel so handle is on the side where hinges were just removed. -
Page 25: Changing To A 30- Or 60-Minute Timing Cam
CHANGING TO A 30- OR 60-MINUTE TIMING CAM (on some models) 5. Place new cam (hub side down) over clock shaft. Line up flat WARNING side of shaft with flat side of cam hole. Check that drive lug is in place. -
Page 26: Maintenance Instructions
MAINTENANCE INSTRUCTIONS Clean lint screen before and after each cycle. If dryer does not operate, check the following: ■ Removing accumulated lint: Electrical supply is connected. ■ ■ From inside the dryer cabinet: Circuit breaker is not tripped or house fuse is not blown. ■... -
Page 27: Electronic Control Setup Instructions
ELECTRONIC CONTROL SETUP INSTRUCTIONS (PR/PD models) Accumulator Pricing IMPORTANT If the price is set to one coin 1, then accumulator pricing Electrostatic Discharge (ESD) is in effect. Cycle time can be purchased one coin at a time (PD models) up to the maximum time of 99 minutes. Stacked PD Sensitive Electronics models will credit all money to a cycle with a single button press while ESD problems are present everywhere.