P D 8 5 0 0 Copyright Notice This document is copyrighted 2003, by AAEON Technology In. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
L C D D i s p l a y s P D 8 5 0 0 Packing List The LCD monitor comes with the following standard parts shown as below. Check and make sure they are included and in good condition. If anything is missing or damaged, contact the dealer immediately.
L C D D i s p l a y s P D 8 5 0 0 Safety & Warranty Read these safety instructions carefully. Keep this user's manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning.
Page 5
L C D D i s p l a y s P D 8 5 0 0 The equipment does not work well, or you cannot get it to work according to the users manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage.
L C D D i s p l a y s P D 8 5 0 0 Contents Copyright Notice ..................1 Packing List ....................2 Safety & Warranty ..................3 Chapter 1 General Information Introduction....................7 Open Frame Structure Illustration............8 Features of Display Panels............... 9 Dimension....................12 Chapter 2 Hardware Installation Before Unpacking..................14...
L C D D i s p l a y s P D 8 5 0 0 Introduction Congratulations on your purchase of the Industry Display Panel TFT LCD monitor - a marvelous contribution of cutting edge technology. The LCD monitor has been designed with serious thoughts to present the best performance for most applications.
L C D D i s p l a y s P D 8 5 0 0 Features of Display Panels This menu provides full range of analog interface LCD panels, which are 15”(XGA) high-brightness, long lifetime TFT LCD monitors. Stainless steel open-frame architecture 15”...
Page 11
483(W) x 354.80(H) x 64(D) mm with rack mount bezel OS support: MS DOS, Windows 98, Windows NT, Windows 2000. Net Weight: PD8500: 6.5Kg Touchscreen (Optional) Type: 5-wire. Analog resistive Controller resolution: 4096 x 4096 Light transmission: 80% or higher...
L C D D i s p l a y s P D 8 5 0 0 Environmental Specifications Operating temperature: 0°C to 45°C (32~113°F) Vibration: 5~150Hz, 1G acceleration. Shock: 15G peak acceleration (11 msec. Duration) EMC: FCC / CE Class A Industry LCD Display User’s Manual...
L C D D i s p l a y s P D 8 5 0 0 Before Unpacking It is very important to locate the LCD monitor in a suitable environment. The surface for placing the LCD monitor should be stable and level.
To power up the LCD monitor, use the provided AC-DC adapter and the power cord to connect to the power in jack of the display. The following shows how to tighten the power connector on the display PD8500 Step 1: clips the power connector into the fixing hook.
L C D D i s p l a y s P D 8 5 0 0 Connecting to the Computer Turn off the computer and the LCD monitor before connecting them. Use the Monitor-to-PC VGA cable to connect the LCD monitor to your computer.
Page 18
L C D D i s p l a y s P D 8 5 0 0 Source input diagram Video-in RS-232 (touch screen) S-Video Power-in Important! Select <Input Source> Before You Start the System After connecting the display to the system unit, make sure that appropriate signal input source is selected before you starting computer system.
Page 19
L C D D i s p l a y s P D 8 5 0 0 Step 4: Press the Menu button again to display input source. Step 5: Use the Press button to select input source from VGA, DVI, AV or S-Video. Step 6: Press Menu button to exit.
L C D D i s p l a y s P D 8 5 0 0 Panel Mounting These display panels can be placed on a shelf or table, or mounted onto the wall. To mount them onto the wall, you need the mounting brackets, which you will find in the accessory box.
Page 21
L C D D i s p l a y s P D 8 5 0 0 Sponge Panel Industry LCD Display User’s Manual...
L C D D i s p l a y s P D 8 5 0 0 Rack Mounting (Optional) Optional 19” rack mount frame is also available for all models. Industry LCD Display User’s Manual...
L C D D i s p l a y s P D 8 5 0 0 On Screen Display (OSD) Controller The LCD monitor is very easy and simple to operate. There are five controls below on the rear panel. You can see their respective indicators.
Page 25
L C D D i s p l a y s P D 8 5 0 0 Increase / Moving UP Button To move the locating cursor forward in the OSD Menu, press UP button. To increase the value while adjusting a parameter, press button.
L C D D i s p l a y s P D 8 5 0 0 OSD Control Menu There are six options in the OSD Menu. Press the Menu button to display the main menu. Main Menu < >...
Page 27
L C D D i s p l a y s P D 8 5 0 0 GAMMA: To adjust screen luminance of the display. • Under Image menu, press button to select GAMMA setting. Press Menu button to enter. •...
Page 28
L C D D i s p l a y s P D 8 5 0 0 Geometry H-Position: (VGA mode only) To adjust horizontal position of display. • Press the Menu button again to enter select H-Position setting. • Press button to adjust.
Page 29
L C D D i s p l a y s P D 8 5 0 0 • PD8500:only workable for Display Modes 640x480, 800x600. Phase: To adjusts the phase of pixel frequency and minimizes the video distortion. • Press button to select Phase setting.
L C D D i s p l a y s P D 8 5 0 0 Function Setting Auto set-up: (VGA mode only) Automatically scanning and adjust Clock, Phase, H-position and V-position to the best performance. • Press button to select Auto set-up. Press the Menu button again to enter.
L C D D i s p l a y s P D 8 5 0 0 Return to Menu: Return to main menu selection. OSD Setting Language: Set the language of OSD menu. • Press the Menu button again to select Language. •...
L C D D i s p l a y s P D 8 5 0 0 Return to Menu: Return to main menu selection. Other Settings Signal select: Select the display input source. • Press the Menu button again to select Signal select.
Page 33
L C D D i s p l a y s P D 8 5 0 0 • Press button to select Full screen. Press the Menu button again to enter. • Press button to choose size 1 or 2, or to turn off full screen function.
Page 34
L C D D i s p l a y s P D 8 5 0 0 Exit To exit OSD main menu, press button to select EXIT. Press Menu button again to exit. Brightness Hotkey Control (with Light sensor off) The Hot key control allows you to instant activate frequent use brightness without browsing OSD menu.
L C D D i s p l a y s P D 8 5 0 0 The PD8500 comply with DDC1/DDCB2 standard, therefore the system will automatically detect the display. No drivers’ installation is needed. Touchscreen Driver Installation (Optional) The Touchscreen driver is included in the supporting CD-ROM.
L C D D i s p l a y s P D 8 5 0 0 Output DC 12V / 5A(Max) Troubleshooting Problem: Unclear or Unsteady Display Actions: Activate the AUTO button. You might need to repeat to find balanced values for a good quality. If you still have problem to fine-tune the image, call your local technical support for assistance.