Rinse Aid And Refined Salt; Measuring Out The Rinse Aid; Measuring Out The Refined Salt - Ariston LFD 11M121 Operating Instructions Manual

Rinse aid and refined salt

Only use products which have been specifically designed
EN
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
(Follow the instructions given on the packaging).
very hard.
If you do not add salt or rinse aid, the LOW SALT
LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs off
the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
• When the LOW RINSE AID indicator light
is illuminated, a reserve supply of rinse aid is still available
for 1-2 cycles;
1. Open the dispenser
on the lid;
2. Carefully introduce the rinse aid as far as the maximum
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Rinse-aid dispenser setting
If you are not completely satisfied with the drying results, you
can adjust the quantity of rinse aid. Switch on the dishwasher
using the ON/OFF button, press the Settings button and access
the menu "Rinse-aid dispenser setting" using the buttons next
to the grey arrows. The set level appears on the display
factory level).
Choose the desired level and press the OK button to save the
setting. To exit the function wait a few seconds, press the ESC
button or switch off the machine using the ON/OFF button.
If the rinse aid level is set to ZERO, no rinse aid will be supplied.
The LOW RINSE AID indicator light will not illuminate if you run
out of rinse aid.
Up to maximum 4 levels can be set based on the dishwasher
model.
• If there are streaks on the crockery, set the adjustment device
to a lower number (1-2.)
• If there are drops of water or limescale marks, set the
adjustment device to a higher number (3-4.)
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed specially for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
14
*
on the control panel
"D"
by pressing and pulling up the tab
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
Switch on the dishwasher using the ON/OFF button, press the
Settings button and access the menu "Water hardness" using
the buttons next to the grey arrows. The set level appears on
(water softener set to medium level).
the display
Use the buttons next to the grey arrows to select the desired
*
(1-2-3-4-5 see Table on water hardness)
level
*
and
5 levels. Press the OK button to save the setting.
- To exit the function wait a few seconds, press the ESC button
or switch off the machine using the ON/OFF button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
Water Hardness Table
level °dH
1 0 - 6
2 6 - 11
3 12 - 17
4 17 - 34
*
34 - 50
5
For values between 0°f and 10°f, we do not recommend the use of salt.
*
a setting of 5 may increase cycle duration.
**
1 wash cycle per day.
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees – mmol/l = millimoles per litre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refined salt removes limescale from the water, thus avoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
• When the green float
the cap of the salt dispenser;
• When the LOW RINSE AID indicator light on the control panel
*
is illuminated
(set to
4. Remove the funnel* and wipe any salt residues away from
the opening; rinse the cap under running water and then screw
it on, the head facing downwards so as to let the water flow out
of the four slots (star-shaped arrangement) in the lower part of
the cap (cap with green float
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
When necessary, measure out the salt before a wash cycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
*
Only available in selected models.
up to maximum
Average salt dispenser
capacity duration
°fH mmol/l months
0 - 10 0 - 1 7 months
11 - 20 1,1 - 2 5 months
21 - 30 2,1 - 3 3 months
31 - 60 3,1 - 6 2 months
61 - 90 6,1 - 9 2/3 weeks
and should be filled:
*
cannot be seen by simply looking at
;
1. Remove the lower rack and unscrew the
cap (anticlockwise).
2. The first time you do this: fill the water
tank right up to its edge.
*
3. Position the funnel (see figure)
fill the salt dispenser up to the edge
(approximately 1 kg). It is normal for a little
water to leak out.
*
).
**
and