1. Manuals
  2. Brands
  3. Triton Manuals
  4. Printer
  5. FT5000
  6. Upgrade manual

Triton FT5000 Upgrade Manual

Printer / presenter
Hide thumbs Also See for FT5000:
Table of Contents

Advertisement

Quick Links

See also: User Manual
P
C
H
ORPORATE
EADQUARTERS
522 E. Railroad Street
Long Beach, MS 39560
Phone: (228) 868-1317
Fax: (228) 868-0437
© 2005-2007 Delaware Capital Formation, Inc. All Rights Reserved. Triton Systems of
Delaware, Inc. is an operating company of Dover Electronics, Inc., a subsidiary of Dover
Corporation (NYSE-DOV). DOVER, the DOVER logo and the Dover family of marks
and TRITON, the TRITON logo and the Triton family of marks are registered trade-
marks of Delaware Capital Formation, Inc., a wholly owned subsidiary of Dover Corpo-
ration.
/ P
RINTER
RESENTER
F
U
IELD
PGRADE
(M
RL/FT5000/RT2000)
ODELS
TDN 07100-00051B 06/2007
:

COPYRIGHT NOTICE

A
SSEMBLY
P
ROCEDURES
RMA (R
M
ETURN
ATERIAL
R
A
:
ETURN
DDRESS
21405 Avenue "B"
Long Beach, MS 39560
A
)
UTHORIZATION

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FT5000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Triton FT5000

Summary of Contents for Triton FT5000

  • Page 1: Copyright Notice

    Delaware, Inc. is an operating company of Dover Electronics, Inc., a subsidiary of Dover Corporation (NYSE-DOV). DOVER, the DOVER logo and the Dover family of marks and TRITON, the TRITON logo and the Triton family of marks are registered trade- marks of Delaware Capital Formation, Inc., a wholly owned subsidiary of Dover Corpo-...

  • Page 2: Table Of Contents

    NTRODUCTION This guide covers the steps for replacing the current printer/presenter assembly with an upgraded assembly for Model RL/FT5000/ RT2000 ATMs. These procedures include a list of tools and hardware required for the conversion as well as steps for updating terminal software.

  • Page 3: Nstalling The Rl5000 Printer

    RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE RL5000 P NSTALLING THE RINTER RESENTER PGRADE Follow these steps to install the upgrade kit and associated hardware to the Model RL5000 ATM: EQUIRED ARTS AND OOLS i l l i ) c i e t t n i r r e t...
  • Page 4 RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE Next, remove the printer presenter cable shown in Figure 3 by disconnecting from the presenter board and docking board assemblies. Use the diagonal cutters to cut the Ty wrap that secures the cable to docking board assembly. This cable will be replaced.
  • Page 5 RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE NSTALL THE RINTER RESENTER SSEMBLY Using a phillips screwdriver , start one (1) of the screws included in kit (washer head) shown in Figure 6. Mount the new printer/ presenter assembly under the screw. This will hold the assembly until the other screws are installed. Start the other screw included on the other side.
  • Page 6 ATM. Insert the edge of the paper into the printer take-up slot as shown in Figure 10. NOTE: Paper feeds OVER the bar. The printer will automatically grip and pull the paper into the paper path. * NOTE * Triton recommends the use of 20# thermal printer paper (Triton P/N 05403-00053). This receipt paper has been shown to improve performance and reliability.

  • Page 7: Nstalling The Ft5000 Printer

    IT AND RINTER EZEL The new printer/presenter upgrade for the FT5000 is a pivoting assembly. This allows ease of service access. Follow these steps to install the upgrade kit and associated hardware to the Model FT5000 ATM: EQUIRED ARTS AND...

  • Page 8: Remove

    RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE ISCONNECT EMOVE OWER RESENTER ABLES Disconnect the power, data, and low paper sensor cables from the printer controller board shown in Figure 2. The power and data cables will be removed from the unit. See the following procedures. Disconnect the other end of the data cable at the Docking board assembly (Figure 3).

  • Page 9: Ssembly

    RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE Next, disconnect the printer presenter cable from the presenter board and docking board assemblies. Figures 6 and 7 show connection locations. Remove this cable. This will be replaced with cable (P/N 09120-00208) included in kit. Figure 6.
  • Page 10 EZEL * NOTICE * RECOMMENDATION Early production FT5000 models had no screw holes in the This procedure requires installer to perform steps inside and control panel to attach the included bezel. If your Model outside to the unit. The bezel is mounted on the front fascia FT5000 has no printer rain bezel installed OR you currently (customer side) but secured from the inside cabinet.

  • Page 11: Resenter Assembly

    RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE NSTALL THE RINTER RESENTER SSEMBLY 13. Using a phillips screwdriver, start one (1) of the screws included in kit (washer head) shown in Figure 14. 14. Mount the new printer/presenter assembly under the screw. Figure 15 shows assembly/screw location with printer rotated down.

  • Page 12: Cables

    RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE ONNECT ABLES 16. Connect/route the presenter GPIO cable included (P/N 09120-00208) to the docking board and presenter board assemblies (Figures 18 and 19). Route cable under the printer mounting bracket. Figure 19. Presenter board (left side of Figure 15) Figure 18.
  • Page 13 Note: See next page for service access/replenishing paper steps. Figure 25. Insert receipt paper into printer. * NOTE * Triton recommends the use of 20# thermal printer paper (Triton P/N 05403-00053). This receipt paper has been shown Figure 26. New printer assembly installed.
  • Page 14 RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE The following illustrations show the new pivoting printer assembly installed in a Model FT5000 and the procedures for service access and paper loading.. “ON”) ERVICE CCESS OADING ECEIPT APER OWER Insert paper roll on to spool (insert).

  • Page 15: Nstalling The Rl/Ft/Rt P

    PGRADE ROCEDURE RL/FT/RT P NSTALLING THE RESENTER PGRADE Follow these steps to install the upgrade kit and associated hardware to the Model RL5000, FT5000, and RT2000 ATMs: EQUIRED ARTS AND OOLS ) t r i l l i c i t...

  • Page 16: Assembly (Rl/Ft/Rt)

    RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE Disconnect the presenter board cable (Figure 4) located on the left side of presenter assembly. Using a phillips screwdriver, remove the two (2) screws that secure the presenter assembly and remove the presenter (Figure 5). The screws and presenter assembly will be replaced.

  • Page 17: Printer

    RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE RL5000 P RESENTER PGRADE EMOVE THE OMPLETE RINTER SSEMBLY Remove the receipt paper and spool from the printer assembly. Remove the printer controller board cover, if installed (Figure 1). Disconnect the power, data, and low paper sensor cables from the printer controller board shown in Figure 2. Note the “Red” tracer on the data cable.
  • Page 18 RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE Remove the four (4) phillips screws that secure the printer presenter/strut assemblies shown in Figure 4. Retain the (2) strut screws. Remove the whole printer assembly from the unit. NOTE: There is a ground wire lug attached to the lower right screw shown.
  • Page 19 RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE EINSTALL THE OMPLETE RINTER SSEMBLY Using a phillips screwdriver , start one (1) of the screws included in kit (washer head) in the presenter shown in Figure 6. Mount the new printer/presenter assembly under the screw. This will hold the assembly until the other screws are installed.

  • Page 20: Remove The Presentera

    RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE FT5000 P RESENTER PGRADE EMOVE THE RESENTER SSEMBLY Remove the receipt paper and spool from the printer assembly. Lift the printer handle and rotate the printer assembly down (Figures 1 and 2). Figure 2. Rotate printer down.
  • Page 21 RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE NSTALL RESENTER SSEMBLY Using a phillips screwdriver , start one (1) of the screws included in kit (washer head) in the control panel (Figure 7). Reconnect the presenter cable to the new presenter. Insert the new presenter on the screw and start the other. Do not tighten at this time. Next, install the Torx screws previously removed.

  • Page 22: Pdating Erminal Oftware

    ERMINAL OFTWARE This step procedure describes how to perform a software update for the RL/FT5000/RT2000. You will need a Flash drive device (USB storage device shown) with the terminal software loaded in it (CD included in kits have software files specific for model ATM).

  • Page 23: Check

    Main Menu > Terminal Status > Save Parameters to highlight the selected file. Press <Enter> when selected. External Storage (USB device) before loading the Full Load NOTE: Triton recommends loading the UPDATE LOAD file. This allows you to quickly configure terminal with the file when applicable.
  • Page 24 RINTER RESENTER SSEMBLY IELD PGRADE ROCEDURE NTENTIONALLY LANK...

This manual is also suitable for:

Rt2000Rl5000

Table of Contents