Kenwood KDC-BT368U Instruction Manual page 24

AUDIO SETTINGS
SPEAKER SIZE The frequency and slope settings are automatically set for the crossover of
the selected speaker.
FRONT SIZE 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/
7×10: Selects according to the connected speaker size for
optimum performance.
TWEETER SMALL/MIDDLE/LARGE: Selects according to the size
range of the connected tweeter for optimum performance. ;
NONE: Not connected.
REAR 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10: Selects
according to the connected speaker size for optimum performance. ;
NONE: Not connected.
SUBWOOFER 6.5"/8"/10"/12"/15" OVER: Selects according to the connected speaker size
for optimum performance. ; NONE: Not connected.
X ' OVER
TWEETER FRQ 1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/
10KHZ/12.5KHZ: Adjusts the crossover frequency for the
tweeter speaker.
GAIN LEFT –8 to 0: Adjusts the output volume of the left tweeter.
GAIN RIGHT –8 to 0: Adjusts the output volume of the right tweeter.
FRONT HPF F - HPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/
120HZ/150HZ/180HZ/220HZ/250HZ: Adjusts the
crossover frequency for the selected speakers (high pass
filter). ; THROUGH: All signals are sent to the selected
speakers.
F - HPF SLOPE –6DB/–12DB/–18DB/–24DB: Adjusts the crossover
slope.
(Selectable only if a setting other than [THROUGH] is
selected for [F - HPF FRQ].)
F - HPF GAIN –8 to 0: Adjusts the output volume of the selected speaker.
20
ENGLISH
REAR HPF R - HPF FRQ
R - HPF SLOPE
R - HPF GAIN
SUBWOOFER LPF SW LPF FRQ
SW LPF SLOPE –6DB/–12DB/–18DB/–24DB: Adjusts the
SW LPF PHASE REVERSE (180°)/NORMAL (0°): Selects the phase
SW LPF GAIN
DTA SETTINGS Digital Time Alignment sets the delay time of the speaker output to
create a more suitable environment for your vehicle.
For more information, refer to the illustration on page 21.
POSITION Selects your listening position (reference point).
ALL: Not compensating ; FRONT RIGHT: Front right seat ;
FRONT LEFT: Front left seat ; FRONT ALL: Front seat
DISTANCE 0FT to 20.01FT: Fine adjust the distance to compensate. (Before
making an adjustment, select the speaker you want to adjust.)
GAIN –8DB to 0DB: Fine adjust the output volume of the selected speaker.
(Before making an adjustment, select the speaker you want to adjust.)
DTA RESET YES: Resets the settings ([DISTANCE] and [GAIN]) of the selected
[POSITION] to default. ; NO: Cancels.
(Refer FRONT HPF settings.)
30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/
100HZ/120HZ/150HZ/180HZ/220HZ/250HZ:
Adjusts the crossover frequency for the subwoofer
(low pass filter). ; THROUGH: All signals are sent to
the subwoofer.
crossover slope.
(Selectable only if a setting other than [THROUGH] is
selected for [SW LPF FRQ].)
of the subwoofer output to be in line with the
speaker output for optimum performance.
–8 to 0: Adjusts the output volume of the
subwoofer.