Page 1
日立牌电动锤钻 Rotary Hammer DH 30PC2 使用说明书 Handling instructions 使用前务请详加阅读 Read through carefully and understand these instructions before use.
Page 4
17mm – 钻头 Drill bit SDS-plus 长柄部 Part of SDS-plus shank 前帽 Front cap 夹卡 Grip 防尘杯 Dust cup 选择杆 Change lever 按钮 Push button 钻头夹盘 Drill chuck 夹盘附加器 Chuck adapter 夹盘附加器 ( D ) Chuck adapter (D) 螺丝钻头 Driver bit 夹紧器...
Page 5
d) 在电动工具接通之前,拿掉所有调节钥匙或扳 一般安全规则 手。 遗留在电动工具旋转零件上的扳手或钥匙会导 致人身伤害。 警告! e) 手不要伸得太长。 阅读说明 没有按照以下列举的说明而使用或操作将导致触电、 时刻注意脚下和身体平衡。 这样在意外情况下能很好地控制电动工具。 着火和/或严重伤害。 f ) 着装适当。 在所有以下列举的警告中术语“电动工具”指市电驱 动(有线)电动工具或电池驱动(无线)电动工具。 不要穿宽松衣服或佩带饰品。 让你的头发、衣服和袖子远离运动部件。 保存这些说明 宽松衣服、佩饰或长发可能会卷入运动部件。 1) 工作场地 g) 如果提供了与排屑装置、集尘设备连接用的装 a) 保持工作场地清洁和明亮。 置,则确保他们连接完好且使用得当。 混乱和黑暗的场地会引发事故。 使用这些装置可减少碎屑引起的危险。 b) 不要在易爆环境,如有易燃液体、气体或粉尘 4) 电动工具使用和主意事项 的环境下操作电动工具。 a) 不要滥用电动工具,根据用途使用适当的电动 电动工具产生的火花会点燃粉尘或气体。 c ) 让儿童和旁观者离开后操纵电动工具。...
Page 13
d) Remove any adjusting key or wrench before GENERAL SAFETY RULES turning the power tool on. A wrench or a key left attached to a rotating part WARNING! Read all instructions of the power tool may result in personal injury. e) Do not overreach.
Use auxiliary handles supplied with the tool. PRECAUTIONS ON USING ROTARY HAMMER Loss of control can cause personal injury. Always hold the body handle and side handle of Wear ear protections the power tool firmly. Otherwise the counterforce Exposure to noise can cause hearing loss. produced may result in inaccurate and even Do not touch the bit during or immediately after dangerous operation.
13 mm drill chuck ass’y (includes chuck wrench) and chuck (for drilling in steel or wood). 10. Driving Screws (rotation only) Bit No. Chuck adapter (D) (SDS-plus shank) Bit No. Screw Size Length No. 2 3 – 5 mm 25 mm No.
Page 18
To operate the change lever, press the push button, Do not attempt to drill anchor holes or holes in and release the lock of the change lever. Also, check concrete with the machine set in the rotation only and make sure after operation that the push button function.
NOTE: (1) Mount the core bit to the core bit shank. (Fig. 14). The Hitachi Electric Hammer Grease A is of the low Lubricate the thread of the core bit shank to facilitate viscosity type. When the grease is consumed, disassembly.
Page 20
C: No. Used D: Remarks CAUTION Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance.