Related Manuals for Guardian DCS2
Summary of Contents for Guardian DCS2
-
Page 1: Installation Instructions
DCS2 Model Installation Instructions Owner’s Manual READ THIS MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION Installer: Permanently attach manual to the wall. BSOMU06A-1... - Page 2 Specification Electrical Rating Input AC 220V~240V 50/60Hz Current Power ~200W Standby power <1W (Upon door is fully stopped and courtesy light is off) Motor Type DC 24V Brush Max. capacity 800Nmm Operation Lifting capacity 35kg Travel rate 150mm/s approx. Door Type Max.
- Page 3 Connect the power cord to a properly grounded outlet only. Do not in any way alter or remove the grounding pin. Photo Eye System must be installed properly. Guardian Operators recommend Photo Eye System is installed on every garage door for your added protection. Opening doors must not close and Closing doors must open once the beam is broken.
-
Page 4: Product Features
Product Features Motor: Permanent Magnet Direct Current 24V DC Brush Motor. Opener Lights: Turn on and off automatically with 4.5 minutes illumination for your safety and convenience. Sensing System: A built-in sensing system detects obstructions during door operation. If in the Downward (close) travel mode, the Opener will sense an obstruction and reverse to the full open position. - Page 5 Door Test Before beginning installation of the operator please complete the following test to insure that your door is balanced and in good working condition. A poorly balanced door could cause severe personal injury and damage to the opener. Always have a qualified garage door service person make any needed adjustments and/or repairs to your door before proceeding with installation.
- Page 6 Components Identification and Inventory (10) (01) Power Head (02) Header Bracket (03) Door Bracket (04) Door Arm: Curved (05) Door Arm: Straight (06) Warning Label (07) Remote Control (08) Trolley (09) Rail Assembly (10) Rail support Fastener (parts in screw bag) Identification (01) Hex Bolt 5/16”18x1 (4 pcs) (02) Lag Screw # 5/16- 9x2”...
- Page 7 Assembly 01 STEP 1. Remove packing materials. STEP 2. Insert trolley (see fig.2). STEP 3. 2 . 1/4” -20Hex Flange Place the rail support on the power head. Align rail and Nuts (4) power head and slide rail over drive shaft & retaining lugs. Fasten with 4 nuts.
- Page 11 Assembly 05 STEP 17.(OPTIONAL) Put signal wires through the hole on the up right side. STEP 18.(OPTIONAL) Pull out the signal wires from hole of the front side...
- Page 12 Interface Photo Eye Selection Ground Jumper off = Selected Push Button Inside Inside Alternative Floor-mounting Garage Garage Place the Photo Eyes facing each other on each side of the garage door, as shown in Fig.2. If attaching to concrete, secure the photo eyes using Alignment concrete anchors and bolts (not provided).
-
Page 13: Travel Limit Adjustment- I. Up Limit
Travel Limit Adjustment— I. UP Limit WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. -
Page 14: Travel Limit Adjustment- Ii. Down Limit
Travel Limit Adjustment— II. DOWN Limit WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. -
Page 15: Auto Force Adjustment
Auto Force Adjustment WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. -
Page 16: Testing The Safety Reverse System
Testing the Safety Reverse System Warning: Failure to Test Reversing System Could Result in Death or Serious Injury. Test This System Once A Month. To test the Opener Reversing Feature at floor level place a solid object 5cm thick on the ground so that the center of the door will come into contact with it. -
Page 17: Programming The Remote Controls
Programming the Remote Controls 1. To program transmitter, press “RADIO SET” button, “OK” LED flashes twice. The unit is ready to accept a transmitter within a 30 seconds time frame. DOWN LIMIT FORCE DOWN 2. Press any button on the transmitter within 30 seconds. DOWN FORCE LIMIT... -
Page 18: Final Installation
9. On doors with extension type springs, safety restraint cables have been installed through the springs. 10. There is surge protection on the power line to the opener. ***Guardian Operators recommend photo eyes to be installed on all garage doors for added safety***... -
Page 19: After The Installation
After the Installation 1. Never permit children to play with or operate the garage door opener either from the wall station or the remote controls. Keep radio transmitter locked in the car. Misuse of the push button or transmitter could result in serious injury or even death. - Page 20 Rail and Hardware Parts List A-12 A-13 A-11 A-10 Housing Assembly Dome Cover LED Light Logic Board Logic Board Holder RPM Reader Motor Transformer Standby Power Module A-10 LED Light Cover A-11 Chassis A-12 Power Cord A-13 Rail Support...