All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JY 0866 BU TV Consumer Care...
EN 2 Q528.2E LA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.3 Multimedia 1.1 Technical Specifications 1.2 Connections Supported file formats : JPEG 1.3 Chassis Overview : MP3 : Slideshow (.alb) Notes: •...
Page 3
Technical Specifications, Connections, and Chassis Overview Q528.2E LA EN 3 Connections SPDIF EXT 2 EXT 1 EXT 3 SERV. U (RGB/CVBS) (RGB/CVBS) AUDIO OUT AUDIO IN TV ANTENNA OPTIONAL AUDIO IN: LEFT / RIGHT HDMI 3 HDMI 2 HDMI 1 HDMI 1 / DVI HDMI 2 / DVI HDMI 3 / DVI...
Page 4
EN 4 Q528.2E LA Technical Specifications, Connections, and Chassis Overview 1.2.2 Rear Connections - D2- Data channel - D1+ Data channel - Shield Service Connector (UART) - D1- Data channel - Ground - D0+ Data channel - UART_TX Transmit - Shield - UART_RX Receive - D0-...
Page 5
Technical Specifications, Connections, and Chassis Overview Q528.2E LA EN 5 Chassis Overview MAIN SUPPLY PANEL SMALL SIGNAL KEYBOARD CONTROL BOARD PANEL H_17650_083.eps 160108 LIGHT GUIDE PANEL IR & LED PANEL H_17650_086.eps 230508 Figure 1-6 PWB/CBA locations sets with AmbiLight MAIN SUPPLY PANEL SMALL SIGNAL KEYBOARD CONTROL...
• Use only lead-free soldering tin Philips SAC305 with order the mass of the set by a wristband with resistance. Keep code 0622 149 00106. If lead-free solder paste is required, components and tools also at this same potential.
2006 week 17). The 6 last digits contain the It is easy to do, and is a good service precaution. serial number. 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
Index of this chapter: 4.1 Cable Dressing Notes: 4.2 Service Positions • Figures below can deviate slightly from the actual situation, 4.3 Assy/Panel Removal ME8(+) Styling due to the different set executions. 4.4 Set Re-assembly Cable Dressing I_17651_001.eps 110608 Figure 4-1 Cable dressing 32" sets without AmbiLight...
Page 9
Mechanical Instructions Q528.2E LA EN 9 H_17650_085.eps 170108 Figure 4-2 Cable dressing 42" sets with AmbiLight H_17650_087.eps 160108 Figure 4-3 Cable dressing 42" sets without AmbiLight...
Page 10
By laying the TV face down on the (ESD protective) foam bars, a stable situation is created to perform measurements and alignments. By placing a mirror under the TV, you can monitor the screen. Assy/Panel Removal ME8(+) Styling 4.3.1 Rear Cover Warning: Disconnect the mains power cord before you remove the rear cover.
Page 11
Mechanical Instructions Q528.2E LA EN 11 H_17650_100.eps 180108 Figure 4-5 Back Cover Removal [1/3] H_17650_101.eps 180108 H_17650_099.eps 180108 Figure 4-7 Back Cover Removal [3/3] Figure 4-6 Back Cover Removal [2/3]...
Page 12
EN 12 Q528.2E LA Mechanical Instructions 4.3.2 Ambilight Refer to next figure for details. 1. Unplug the connectors [1]. 2. Remove the screws [2]. 3. Pull the unit sidewards from the back cover. When defective, replace the whole unit. H_17650_095.eps 180108 Figure 4-10 Tweeter 4.3.5...
Page 13
Mechanical Instructions Q528.2E LA EN 13 4.3.6 Key Board 4.3.7 Display Supply Panel Refer to next figure for details. Refer to next figure for details. 1. Unplug the key board connector from the IR & LED board. 1. Unplug connectors [1]. 2.
Page 14
EN 14 Q528.2E LA Mechanical Instructions 4.3.8 Small Signal Board (SSB) Refer to next figure for details. Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the SSB. Refer to next figures or details.
Page 15
Mechanical Instructions Q528.2E LA EN 15 4.3.9 LCD Panel / Lightguide Refer to next figures for details. 1. Unplug the LVDS connector [1]. Caution: be careful, as this is a very fragile connector! 2. Unplug the connectors [2]. 3. Remove the fixation screws [3] from rim. 4.
EN 16 Q528.2E LA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: – Picture mute (blue mute or black mute). 5.1 Test Points – Automatic volume levelling (AVL). 5.2 Service Modes –...
Page 17
Contents of SAM: Code • Hardware Info. – A. SW Version. Displays the software version of the main software (example: Q582E-1.2.3.4 = 39mm PHILIPS AAAAB_X.Y.W.Z). MODEL: • AAAA= the chassis name. 32PF9968/10 PROD.SERIAL NO: • B= the region: A= AP, E= EU, L= LatAm, U = US.
Page 18
EN 18 Q528.2E LA Service Modes, Error Codes, and Fault Finding 5.2.3 Customer Service Mode (CSM) - the serial number of the SSB, which consists of seven digits. Both can be found on a sticker on the PWB of the SSB itself.
Page 19
Service Modes, Error Codes, and Fault Finding Q528.2E LA EN 19 the customer wants to make use of the HDMI functionality, the SSB has to be replaced. • Tuner frequency. Indicates the frequency the transmitter is tuned to. • TV System. Gives information about the video system of the selected transmitter.
Page 20
EN 20 Q528.2E LA Service Modes, Error Codes, and Fault Finding Stepwise Start-up due to overvoltage. It is recommended to measure first the FET 7U08 on short-circuit before activating SDM via the service pads. There are two possible situations: one for protections detected When the TV is in protection state due to an error detected by by the stand-by software and one for protections detected by main software (MIPS protection) and SDM is activated via...
Page 21
Service Modes, Error Codes, and Fault Finding Q528.2E LA EN 21 Stand by or Protection Mains is applied Standby Supply starts running. All standby supply voltages become available. st-by µP resets If the protection state was left by short circuiting the SDM pins, detection of a protection condition during startup will stall the startup.
Page 22
EN 22 Q528.2E LA Service Modes, Error Codes, and Fault Finding Enable the supply fault detection algorithm Standby line set to HIGH for 5 seconds Set I²C slave address of Standby µP to (A0h) This will allow access to NVM and NAND FLASH and can not be done Switch LOW the RESET-NVM_WP-NANDFLASH line.
Page 23
Service Modes, Error Codes, and Fault Finding Q528.2E LA EN 23 Release Pacific reset and wait 200ms Blink Code as error code Ping the Pacific through I²C Pacific acknowledges? Third Pacific boot retry? Initialize Pacific Log Pacific error This is needed here because the Pacific has to deliver an output Enable the Pacific output by sending the PanelConfig.PanelOn clock towards the DFI.
Page 24
EN 24 Q528.2E LA Service Modes, Error Codes, and Fault Finding Semi Standby action holder: AVC action holder: St-by autonomous action Wait until previous on-state is left more than 2 seconds ago. (to prevent LCD display problems) Assert RGB video blanking and audio mute Rewrite Pacific register 0x03 (output format) with TcuUpdate: this command is sometimes not processed properly by the...
Page 25
Service Modes, Error Codes, and Fault Finding Q528.2E LA EN 25 Active action holder: AVC action holder: St-by autonomous action Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext audio outputs to ground (I/O: audio reset) And wait 5ms switch off LCD backlight...
Page 26
EN 26 Q528.2E LA Service Modes, Error Codes, and Fault Finding Semi Stand by If ambientlight functionality was used in semi-standby (lampadaire mode), switch off ambient light (see CHS ambilight) *) If this is not performed and the set is Delay transition until ramping down of ambient light is switched to standby when the switch off of finished.
Page 27
Service Modes, Error Codes, and Fault Finding Q528.2E LA EN 27 action holder: MIPS Log the appropriate error and set stand-by flag in NVM action holder: St-by autonomous action Redefine wake up reasons for protection state and transfer to stand-by µP. Switch off LCD lamp supply Wait 250ms (min.
Page 28
EN 28 Q528.2E LA Service Modes, Error Codes, and Fault Finding supply detection algorithms for DC-DC outputs DETECT 1 = Low ? Polling every 40ms Check DETECT1 5 times ( within 500us ) DETECT 1 = Low ? 5 consecutive times ? Shutdown ( Active to Semistdby to standby ) Wait for 5 seconds...
Page 29
Service Modes, Error Codes, and Fault Finding Q528.2E LA EN 29 +12V supply detection algorithm. See CHS protections. DETECT 2 = Low ? Polling every 40ms Check DETECT2 5 times ( within 500us) DETECT 2 = Low ? 5 consecutive times ? Shutdown ( Active to Semistdby to standby ) Wait for 5 seconds...
Page 30
Introduction The error code buffer contains all detected errors since the last ComPair (Computer Aided Repair) is a Service tool for Philips time the buffer was erased. The buffer is written from left to Consumer Electronics products. and offers the following: right, new errors are logged at the left side, and all other errors 1.
Page 31
Service Modes, Error Codes, and Fault Finding Q528.2E LA EN 31 code and not the actual cause (e.g., a fault in the protection and Stand-by Processor broken, etc...). When error 5 detection circuitry can also lead to a protection). occurs it is also possible that I C2 bus is blocked (NVM).
EN 32 Q528.2E LA Service Modes, Error Codes, and Fault Finding The Blinking LED Procedure Protections 5.6.1 Introduction 5.7.1 Software Protections The blinking LED procedure can be split up into two situations: Most of the protections and errors use either the stand-by •...
Page 33
Service Modes, Error Codes, and Fault Finding Q528.2E LA EN 33 5.8.3 DC/DC Converter 1. Check the ENABLE-3V3 signal (active "low"), 2. Check the voltage on pin 8 (1.5 V), 3. Check the under-voltage detection circuit (the voltage on Introduction collector of transistor 7U01-1 should be less than •...
Page 34
EN 34 Q528.2E LA Service Modes, Error Codes, and Fault Finding 5.8.5 SSB Replacement Follow the instructions in the flowchart in case you have to exchange the SSB. See figure “SSB replacement flowchart”. START Set is still operating? Activate SAM and save the TV settings via “Upload to USB”...
Page 35
1. Disconnect the TV from the Mains/AC Power. SSB. 2. Press the “OK” button on a Philips DVD RC-6 remote control (it is also possible to use the TV remote in “DVD” Automatic Software Upgrade mode).
Page 36
5.9.4 Content and Usage of the One-Zip Software File 2. Press the “CURSOR DOWN” button on a Philips DVD RC- 6 remote control (it is also possible to use the TV remote in Below you find a content explanation of the One-Zip file, and “DVD”...
Block Diagrams, Test Point Overview, and Waveforms Q528.2E LA Wiring Diagram 42" (ME8) WIRING DIAGRAM 37"- 42" (STYLING ME8) 8GC3 8GC0 8GC2 8GC1 LCD DISPLAY (1004) 8401 BEHIND DOOR 8402 IN BACK COVER LVDS INPUT (1080p) DANGEROUS DANGEROUS HIGH VOLTAGE...
Block Diagrams, Test Point Overview, and Waveforms Q528.2E LA Block Diagram Video VIDEO B03A B05C B06C B06A MAIN TUNER PNX8541 PNX5050: VIDEO PACIFIC 3 PACIFIC 3: LVDS 7H00 7T57 1T04 TDA9898HL PNX8541E/M1 1T75 TD1716F/BHXP 7T56 B04K ANALOGUE AV IF-FILTP1 1G50 IF1-A B04O DIGITAL...
Circuit Diagrams and PWB Layouts Q528.2E LA SSB: SRP List Explanation Example Personal Notes: 1.1. Introduction Net Name Diagram +12-15V AP1 (4x) +12-15V AP4 (4x) SRP (Service Reference Protocol) is a software tool that creates a list with all references to signal lines. The list contains +12-15V AP5 (12x) references to the signals within all schematics of a PWB.
Alignments Q528.2E LA EN 115 8. Alignments Index of this chapter: For the next alignments, supply the following test signals via a 8.1 General Alignment Conditions video generator to the RF input: 8.2 Hardware Alignments • EU/AP-PAL models: a PAL B/G TV-signal with a signal 8.3 Software Alignments strength of at least 1 mV and a frequency of 475.25 MHz 8.4 Option Settings...
Light sensor Present / Not present MOP present / not present Light sensor type Step / ME7 / MS7 / ME8 / Canvas / Aurea Styling Source selection HDMI 3 Present / Not present HDMI 3 Present / Not present...
Page 117
Alignments Q528.2E LA EN 117 8.4.4 Opt. No. (Option numbers) Select this sub menu to set all options at once (expressed in The first line (group 1) indicates hardware options 1 to 4, the two long strings of numbers). second line (group 2) indicates software options 5 to 8. An option number (or "option byte") represents a number of Every 5-digit number represents 16 bits (so the maximum value different options.
Page 118
This chassis (member of the “TV522“ platform) is a derivative from the Q528.1E LA chassis (member of the “TV520” The main features for this chassis are: platform). It comes with a new styling called “ME8(+)” which, in • The introduction of a module referred to as “Light Guide” on some sets, incorporates a light strip on the front side of the set the front side of the set (in some sets).
Page 119
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.2E LA EN 119 9.1.3 SSB Cell Layout SERVICE CONNECTOR ANALOG I/O SIDE I/O PNX5050 AUDIO CLASS - D PNX85XX DC - DC CONVERSION COMMON INTERFACE MPEG4 (OPT) DIGITAL I/O H_17650_090.eps 160108 Figure 9-2 SSB top view PACIFIC3 (OPT) H_17650_091.eps...
Page 120
EN 120 Q528.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Main Supply Abbreviation List 9.2.1 32" Sets 0/6/12 SCART switch control signal on A/V board. 0 = loop through (AUX to TV), 6 = play 16:9 format, 12 = play 4:3 The 32"...
Page 121
EPLD Erasable Programmable Logic Device LORE LOcal REgression approximation Europe noise reduction EXTernal (source), entering the set by LG.Philips LCD (supplier) SCART or by cinches (jacks) Loudspeaker Fast BLanking: DC signal LVDS Low Voltage Differential Signalling accompanying RGB signals Mbps...
Page 122
4.406250 MHz and 4.250000 MHz Sound Intermediate Frequency SMPS Switched Mode Power Supply System on Chip Sync On Green SOPS Self Oscillating Power Supply S/PDIF Sony Philips Digital InterFace SRAM Static RAM Small Signal Board STBY STand-BY SVGA 800x600 (4:3) SVHS...
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.2E LA EN 123 IC Data Sheets This section shows the internal block diagrams and pin configurations of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs).
Page 124
EN 124 Q528.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.2 Diagram B03A, TDA9898HL (IC 7T57) Block Diagram 4 MHz reference input EXTERNAL SOUND BAND-PASS FILTER i.c. ADRSEL GNDD LFSYN2 GNDA EXTFILO EXTFILI FREF OPTXTAL 43, 44 40, 41 SYNTHESIZER 4 MHz FREQUENCY C-BUS...
Page 125
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.2E LA EN 125 9.4.3 Diagram B03B, TDA10048HN (IC7T17-1) Block Diagram AGC_TUN AGC_IF ANALOG ΣΛ STEP INTERFACE DIGITAL FRONT-END DUAL CHANNEL ESTIMATION AND OFDM AND CORRECTION DEMODULATION ΣΛ STEP INTERFACE DIGITAL DYNAMIC 2K / 4K / 8K TIMESHIFT CANCELLER...
Page 126
EN 126 Q528.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.4 Diagram B03C, TDA10023HT (IC7TA4) Block Diagram DDA1 SSA1 DDD3 SSD3 DDD2 SSD2 DDD1 SSD1 DDA2 DDA3 SSA3 DDD4 XOUT 8, 25, 42 14, 30, 43 15, 31, 44 AGCTUN CLOCK RECOVERY...
Page 127
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.2E LA EN 127 9.4.5 Diagram B03D to H, STi7101 (IC7A00) Block Diagram 5 x 2-ch S/PDIF PCM out Peripheral I/O SDRAM AudioL 2-ch and external interrupts AudioR PCM in video in Audio ST40 core 266 MHz Serial...
Page 128
EN 128 Q528.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.6 Diagram B04, PNX85xx (IC 7H00) Block Diagram DDR-II DDR-II 32 MB 32 MB PNX85xx Matrix Display 1368 × 768 A/V INPUTS MIPS32@240MHz TV control, Pixel OSD Source select 3D-Comb Digital color decoder Audio decoding...
Page 129
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.2E LA EN 129 9.4.7 Diagram B05, PNX5050 (IC 7C00) Block Diagram DDR SDRAM PNX5050 MAIN MEMORY INTERFACE SD video ITU-R BT.656 PICTURE 4 : 2 : 2 VIDEO IN IMPROVEMENT 24-bit RGB/ HD video YUV ROUTER OUTPUT...
Page 130
EN 130 Q528.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.8 Diagram B06C, T6TF4HFG (IC 7GE2) Block Diagram Contrast Reserve Input Proc Contr, Brightness & & Clip Measure MVL manager White-point corr Color LUT Color gamut & Dithering Sharpness mapping Contr.
Page 131
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.2E LA EN 131 9.4.9 Diagram B08A, ISP1564HL (IC 7P00) Block Diagram PME# 77, 98, 100 CC(IO)AUX GLOBAL CONTROL 10, 12 to 15, 20 to 22, AD[31:0] 26 to 31, 33, 34, 50 to 54, 56, 57, PCI CORE VOLTAGE...
Page 132
EN 132 Q528.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.10 Diagram B08C, AD8197A (IC 7P70) Block Diagram Figure 1. TYPICAL APPLICATION 04:20 Pin Configuration AVCC AVCC PIN 1 INDICATOR IN_B0 IP_C3 IP_B0 IN_C3 AVEE AVEE IN_B1 IP_C2 IP_B1 IN_C2 VTTI...
Page 133
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.2E LA EN 133 9.4.11 Diagram B09B, STE100P (IC 7NA1) Block Diagram LEDS LEDS TX Channel 100Mb/s Parallel to Scrambler NRZ To NRZI Binary To MLT3 TX_CLK 4B/5B Serial Encoder Encoder TXD[3:0] TRANSMITTER TX_ER 10/100...
Page 134
EN 134 Q528.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.12 Diagram B10A, TDA8932B (IC 7D10) Block Diagram BOOT1 OSCILLATOR DDP1 IN1P DRIVER HIGH OUT1 CTRL MODULATOR DRIVER SSP1 IN1N MANAGER BOOT2 INREF DDP2 IN2P DRIVER HIGH OUT2 CTRL MODULATOR DRIVER...
Spare Parts List & CTN Overview Q528.2E LA EN 135 10. Spare Parts List & CTN Overview For the latest spare part overview, please consult the Philips Service website. Table 10-1 Sets described in this manual: Styling 32PFL7403D/79 42PFL5603D/10 42PFL5603D/12...