All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by TY 0871 BU TV Consumer Care...
EN 2 Q522.2E LA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.4 Miscellaneous 1.1 Technical Specifications 1.2 Connections Power supply: 1.3 Chassis Overview : 220 - 240 ± 10% - Mains voltage (V - Mains frequency (Hz) : 50 / 60 Notes:...
Page 3
Technical Specifications, Connections, and Chassis Overview Q522.2E LA EN 3 Connections I_18010_067.eps 110608 Figure 1-1 Connection overview Note: The following connector colour abbreviations are used 13 - Ground Red (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= 14 - Ground P50 Grey, Rd= Red, Wh= White, Ye= Yellow.
Page 4
EN 4 Q522.2E LA Technical Specifications, Connections, and Chassis Overview 7 - HDMI 1, 2 & 3 Digital Video, Digital Audio - In 10 - Cinch: Audio - In Rd - Audio R 0.5 V / 10 kohm Wh - Audio L 0.5 V / 10 kohm E_06532_017.eps...
Page 5
Technical Specifications, Connections, and Chassis Overview Q522.2E LA EN 5 MAIN SUPPLY PANEL SMALL SIGNAL KEYBOARD CONTROL BOARD PANEL IR & LED PANEL I_18011_015.eps 240908 Figure 1-6 PWB locations 37” MAIN SUPPLY PANEL SMALL SIGNAL KEYBOARD CONTROL BOARD PANEL I_18010_009.eps IR &...
• Use only lead-free soldering tin Philips SAC305 with order the mass of the set by a wristband with resistance. Keep code 0622 149 00106. If lead-free solder paste is required, components and tools also at this same potential.
2006 week 17). The 6 last digits contain the It is easy to do, and is a good service precaution. serial number. 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
4.2 Service Positions • Figures below can deviate slightly from the actual situation, 4.3 Assy/Panel Removal ME8 Styling due to the different set executions. 4.4 Assy/Panel Removal MG8 Styling 4.5 Set Re-assembly Cable Dressing Tape the LVDS cable to LCD Panel.
Page 9
Mechanical Instructions Q522.2E LA EN 9 I_18011_016.eps 250908 Figure 4-4 Cable dressing 37” Saddles for High Voltage cable dressing Saddle for LVDS cable dressing Saddle 11P, 8P, speaker and Saddle for speaker ferrite IR cable dressing Saddle for 11P cable ferrite ring Saddle for 8P cable ferrite ring Saddle for speaker cable dressing Saddles...
Page 10
EN 10 Q522.2E LA Mechanical Instructions I_18010_061.eps 110608 Figure 4-6 Right speaker cables 42” I_18010_062.eps 110608 Figure 4-7 Right speaker cables (with bar mounted) 42” I_18010_063.eps 110608 Figure 4-8 Felt and tape position for LVDS cable 42”...
Page 11
Mechanical Instructions Q522.2E LA EN 11 Saddles for High Voltage cable dressing Saddle for High Voltage cable dressing Saddle for 8P/11P cable dressing Saddle for LVDS cable dressing 2x Metal bar clamp for dressing High Saddle for Voltage cable. speaker ferrite ring Saddles for IR, Speaker and Mains inlet cables dressing...
Page 12
EN 12 Q522.2E LA Mechanical Instructions Service Positions 4.3.3 IR & LED Board Refer to next figure for details. For easy servicing of this set, there are a few possibilities 1. Unplug connectors [1]. created: 2. Use a flat screw driver to release the clip by pushing in the •...
Page 13
3. Release the wiring tape [3]. I_17750_006.eps 250208 Figure 4-13 LCD Panel removal (photo from Q522.1E chassis) Assy/Panel Removal MG8 Styling 4.4.1 Stand 1. Refer to next figure. 2. Place the TV set upside down on a table top, using the foam bars (see section “Service Position”).
Page 14
EN 14 Q522.2E LA Mechanical Instructions 4.4.2 Rear Cover Warning: Disconnect the mains power cord before you remove the rear cover. 1. Refer to next figures. 2. Place the TV set upside down on a table top, using the foam bars (see section “Service Positions”). 3.
Page 15
Mechanical Instructions Q522.2E LA EN 15 4.4.3 Keyboard Control Board 4.4.5 Power Supply Board 1. Refer to next figure. Due to different set executions this chassis is supplied with one 2. Unscrew two screws[1] or two power supply boards and figures may differ. 3.
Page 16
EN 16 Q522.2E LA Mechanical Instructions 4.4.6 Inverter Board Due to different set executions this chassis some versions are supplied with an inverter board. Figures may differ. 1. Refer to next figure. 2. Unplug all connectors [1]. 3. Release the clips [2] 4.
Service Modes, Error Codes, and Fault Finding Q522.2E LA EN 17 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: – Picture mute (blue mute or black mute). 5.1 Test Points – Automatic volume levelling (AVL). 5.2 Service Modes –...
Page 18
Contents of SAM: Code • Hardware Info. – A. SW Version. Displays the software version of the main software (example: Q522E-1.2.3.4 = 39mm PHILIPS AAAAB_X.Y.W.Z). MODEL: • AAAA= the chassis name. 32PF9968/10 PROD.SERIAL NO: • B= the region: A= AP, E= EU, L= LatAm, U = US.
Page 19
Service Modes, Error Codes, and Fault Finding Q522.2E LA EN 19 5.2.3 Customer Service Mode (CSM) SSB itself. The format of the identification number is then as follows: <last seven characters of 12NC of SSB><serial number of SSB> (total fourteen characters). Purpose •...
Page 20
EN 20 Q522.2E LA Service Modes, Error Codes, and Fault Finding the customer wants to make use of the HDMI functionality, • DFI Software (if applicable). Displays the DFI EPLD the SSB has to be replaced. software. • Tuner Frequency. Indicates the frequency the transmitter •...
Page 21
Service Modes, Error Codes, and Fault Finding Q522.2E LA EN 21 Off/Stby to Semi Stand by or Protection Mains is applied Standby Supply starts running. All standby supply voltages become available . st-by µP resets If the protection state was left by short circuiting the SDM pins, detection of a protection condition during startup will stall the startup.
Page 22
EN 22 Q522.2E LA Service Modes, Error Codes, and Fault Finding (pulling pin of the probe interface to ground by inserting EJTAG probe) An EJTAG probe (e.g. WindPower ICE probe) can be connected for Linux Kernel debugging purposes. EJTAG probe connected ? Cold boot? Release AVC system reset...
Page 23
Service Modes, Error Codes, and Fault Finding Q522.2E LA EN 23 Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC . - Between 5 and 50 ms after power is supplied, display should receive valid LVDS clock . action holder: AVC - Backlight Control PWM output should always keep low until LVDS power is supplied .
Page 24
EN 24 Q522.2E LA Service Modes, Error Codes, and Fault Finding action holder: AVC Active action holder: St-by autonomous action Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext. audio outputs to ground (I/O: audio reset) and wait 5ms Switch “off”...
Page 25
Service Modes, Error Codes, and Fault Finding Q522.2E LA EN 25 Semi Stand by If ambientlight functionality was used in semi -standby (lampadaire mode), switch “off” ambient light *) If this is not performed and the set is Delay transition until ramping down of ambient light is switched to standby when the switch “off”...
Page 26
EN 26 Q522.2E LA Service Modes, Error Codes, and Fault Finding action holder: MIPS action holder: St-by autonomous action Log the appropriate error and set stand-by flag in NVM Redefine wake up reasons for protection state and transfer to stand-by µP. Switch “off”...
Page 27
Service Modes, Error Codes, and Fault Finding Q522.2E LA EN 27 supply detection algorithms for DC-DC outputs DETECT 1 = Low ? Polling every 40ms Check DETECT1 5 times ( within 500us ) DETECT 1 = Low ? 5 consecutive times ? Shutdown ( Active to Semistdby to standby ) Wait for 5 seconds...
Page 28
EN 28 Q522.2E LA Service Modes, Error Codes, and Fault Finding +12V supply detection algorithm DETECT 2 = Low ? Polling every 40ms Check DETECT2 5 times ( within 500us) DETECT 2 = Low ? 5 consecutive times ? Shutdown ( Active to Semistdby to standby ) Wait for 5 seconds Restart...
Introduction The error code buffer contains all detected errors since the last ComPair (Computer Aided Repair) is a Service tool for Philips time the buffer was erased. The buffer is written from left to Consumer Electronics products. and offers the following: right, new errors are logged at the left side, and all other errors 1.
Page 30
EN 30 Q522.2E LA Service Modes, Error Codes, and Fault Finding code and not the actual cause (e.g., a fault in the protection the DC/DC +3V3-STANDBY_+1V2-STANDBY (B02B) detection circuitry can also lead to a protection). probably 1V2 STANDBY and 3V3 STANDBY under There are several mechanisms of error detection: voltage cause the "DETECT1"...
Service Modes, Error Codes, and Fault Finding Q522.2E LA EN 31 The Blinking LED Procedure Protections 5.6.1 Introduction 5.7.1 Software Protections The blinking LED procedure can be split up into two situations: Most of the protections and errors use either the stand-by •...
Page 32
EN 32 Q522.2E LA Service Modes, Error Codes, and Fault Finding Fault Finding and Repair Tips - the stand-by microprocessor is detecting that and switching “off” all supply voltages. 1. Check the drop voltage across resistor 3U70 or 3U3T Read also paragraph “Error Codes” -> “Error Buffer” -> “Extra (they could be too high, meaning a defective controller Info”.
Page 33
Service Modes, Error Codes, and Fault Finding Q522.2E LA EN 33 5.8.4 SSB Replacement Follow the instructions in the flowchart in case you have to exchange the SSB. See figure “SSB replacement flowchart”. START Set is still operating? Create “repair” directory on USB stick and connect USB stick to TV-set Go to SAM mode and save the TV settings via “Upload to USB”.
EN 34 Q522.2E LA Service Modes, Error Codes, and Fault Finding 5.8.5 Display option code Caution: In case you have replaced the SSB, always check the display option code in SAM, even if you have picture. With a wrong display option code it is possible that you have picture, but that in certain conditions you have unwanted side-effects.
Page 35
1. Disconnect the TV from the Mains/AC Power. software, use the following steps: 2. Press the “OK” button on a Philips DVD RC-6 remote 1. Disconnect the TV from the Mains/AC Power. control (it is also possible to use the TV remote in “DVD”...
Page 36
EN 36 Q522.2E LA Service Modes, Error Codes, and Fault Finding 5.9.4 Content and Usage of the One-Zip Software File Below you find a content explanation of the One-Zip file (content may vary per chassis), and instructions on how and when to use it.
Block Diagrams, Test Point Overview, and Waveforms Q522.2E LA Block Diagram Video VIDEO B03A MAIN TUNER PNX8541 B05A DUAL LVDS B06A LVDS 7H00 7T57 1T04 PNX8541E/M1 TDA9898HL TD1716F/BHXP 1T55 7T56 IF-FILTP1 B04K ANALOGUE AV 1G50 IF1-A B04O DIGITAL 7CG0 CVBS4 CVBS VIDEO OUT BU7988KVT...
Circuit Diagrams and PWB Layouts Q522.2E LA 7. Circuit Diagrams and PWB Layouts Main Supply Panel (42") MAIN SUPPLY PANEL (42”) I_18011_014.eps 230908...
Page 66
Circuit Diagrams and PWB Layouts Q522.2E LA SSB: PNX8541: Digital Video In Personal Notes: 3HK0 D2 PNX 8541: DIGITAL VIDEO IN 7H00-3 B2 B04H B04H 9HK0 C2 IHKM D2 7H00-3 PNX8541E1/M1/2414 HDMI RX2- RX_0 RX2+ HOT-PLUG HOT_PLUG RX1- RX_1 RX1+ RX0- RX0+ RX_2...
Circuit Diagrams and PWB Layouts Q522.2E LA SSB: SRP List Explanation Example Personal Notes: 1 . 1 . Introduction Net Name Diagram +12-15V AP1 (4x) +12-15V AP4 (4x) SRP (Service Re ference Protocol) is a softw are too l that creates a list w i th all refer e n c es to signal lines. The list contains +12-15V AP5 (12x) +12-15V...
Alignments Q522.2E LA EN 99 8. Alignments Index of this chapter: • Switch the set to stand-by mode. 8.1 General Alignment Conditions 8.2 Hardware Alignments For the next alignments, supply the following test signals via a 8.3 Software Alignments video generator to the RF input: 8.4 Option Settings •...
Page 100
EN 100 Q522.2E LA Alignments Table 8-2 Tint settings 8.4.3 (Service) Options Select the sub menu's to set the initialisation codes (options) of Colour Temp. the set via text menus. 32" Cool Normal 8.4.4 Opt. No. (Option numbers) Warm 37" Select this sub menu to set all options at once (expressed in Cool two long strings of numbers).
Page 101
Alignments Q522.2E LA EN 101 CTN MODEL Displ. code Group 1 Group 2 32PFL5403D/12_6 41472 04109 06223 45160 10137 00098 00004 00000 32PFL5403S/60 41472 04109 06223 45160 10120 00098 00004 00000 32PFL5403S/60 41472 04109 06223 45160 10137 00098 00004 00000 37PFL3403D/12_1 33280 04111...
Page 102
EN 102 Q522.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: 9.1 Introduction 9.2 Power Supply For a description of all circuitry except the PSU, please refer to 9.3 Abbreviation List the Q528.1E LA Service Manual.
Page 103
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 103 9.1.3 SSB Cell Layout Figure 9-2 SSB layout cells (top view)
EN 104 Q522.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Power Supply Table 9-4 “Standby #” is “low” (Semi-standby mode) Description All power supplies described below are a black box for Service. Symbol 3V3 stdby 12Vssb + Vaudio - Vaudio 24Vinv When defective, a new board must be ordered and the...
Page 105
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 105 9.2.4 37” IPB (BPS LIPS250PS04 & DPS-279BP A) Start-up Sequence Control Signals The control/output signals are driven by open collector/open drain type circuits. The drive requirements are 3V3 Logic. Open Collector: 2.2 kohms pull up resistor to +3V3.
Page 106
EN 106 Q522.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.2.6 47” IPB (LGIT PLHL-T722A) Description Nominal voltage 3.3V + 12V - 12V For details refer to panel specs) ± 3% ± 5% Voltage tol. -5%, +10% -5%, +10% Control Signals Min.
Page 107
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 107 Abbreviation List Digital Noise Reduction: noise reduction feature of the set DRAM Dynamic RAM 0/6/12 SCART switch control signal on A/V Digital Rights Management board. 0 = loop through (AUX to TV), Digital Signal Processing 6 = play 16 : 9 format, 12 = play 4 : 3 Dealer Service Tool: special remote...
Page 108
MPIF Multi Platform InterFace Sync On Green MUTE MUTE Line SOPS Self Oscillating Power Supply Not Connected S/PDIF Sony Philips Digital InterFace NICAM Near Instantaneous Compounded SRAM Static RAM Audio Multiplexing. This is a digital Small Signal Board STBY STand-BY sound system, mainly used in Europe.
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 109 IC Data Sheets This section shows the internal block diagrams and pin configurations of ICs that are drawn as “black boxes” in the electrical diagrams (with the exception of “memory” and “logic” ICs).
Page 110
EN 110 Q522.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.2 Diagram B02C, ST1S10PHD (IC 7U0Z) Block Diagram Pin Configuration DFN8 (4x4) PowerSO-8 I_18010_083.eps 130608 Figure 9-8 Internal block diagram and pin configuration...
Page 111
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 111 9.4.3 Diagram B03A, TDA9898HL (IC 7T57) Block Diagram 4 MHz reference input EXTERNAL SOUND BAND-PASS FILTER i.c. ADRSEL GNDD LFSYN2 GNDA EXTFILO EXTFILI FREF OPTXTAL 43, 44 40, 41 SYNTHESIZER 4 MHz FREQUENCY C-BUS...
Page 112
EN 112 Q522.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.4 Diagram B03B, TDA10048HN (IC7T17-1) Block Diagram AGC_TUN AGC_IF ANALOG ΣΛ STEP INTERFACE DIGITAL FRONT-END DUAL CHANNEL ESTIMATION AND OFDM AND CORRECTION DEMODULATION ΣΛ STEP INTERFACE DIGITAL DYNAMIC 2K / 4K / 8K TIMESHIFT CANCELLER...
Page 113
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 113 9.4.5 Diagram B03C, TDA10023HT (IC7TA4) Block Diagram DDA1 SSA1 DDD3 SSD3 DDD2 SSD2 DDD1 SSD1 DDA2 DDA3 SSA3 DDD4 XOUT 8, 25, 42 14, 30, 43 15, 31, 44 AGCTUN CLOCK RECOVERY...
Page 114
EN 114 Q522.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.6 Diagram B04x, PNX85xx (IC 7H00) Block Diagram DDR-II DDR-II 32 MB 32 MB PNX85xx Matrix Display 1368 × 768 A/V INPUTS MIPS32@240MHz TV control, Pixel OSD Source select 3D-Comb Digital color decoder Audio decoding...
Page 115
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 115 9.4.7 Diagram B04M, TS4821DT (IC 7HV3) Typical Application Schematic Rfeed1 Rfeed1 1µF 1µF 3.9k 3.9k Rpol Rpol 100k 100k Right In Right In Cin1 Cin1 3.9k 3.9k 220µF 220µF RL=32Ohms RL=32Ohms...
Page 116
EN 116 Q522.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.8 Diagram B05A, BU7988KVT (IC 7CG0) Block Diagram Pin Configuration I_17970_059.eps 060608 Figure 9-14 Internal block diagram and pin configuration...
Page 117
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 117 9.4.9 Diagram B08A, ISP1564HL (IC 7P00) Block Diagram PME# 77, 98, 100 CC(IO)AUX GLOBAL CONTROL 10, 12 to 15, 20 to 22, AD[31:0] 26 to 31, 33, 34, 50 to 54, 56, 57, PCI CORE VOLTAGE...
Page 118
EN 118 Q522.2E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.10 Diagram B08C, AD8197A (IC 7P70) Block Diagram Figure 1. TYPICAL APPLICATION 04:20 Pin Configuration AVCC AVCC PIN 1 INDICATOR IN_B0 IP_C3 IP_B0 IN_C3 AVEE AVEE IN_B1 IP_C2 IP_B1 IN_C2 VTTI...
Page 119
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q522.2E LA EN 119 9.4.11 Diagram B10A, TDA8932B (IC 7D10) Block Diagram BOOT1 OSCILLATOR DDP1 IN1P DRIVER HIGH OUT1 CTRL MODULATOR DRIVER SSP1 IN1N MANAGER BOOT2 INREF DDP2 IN2P DRIVER HIGH OUT2 CTRL MODULATOR DRIVER...
EN 120 Q522.2E LA Spare Parts List & CTN Overview 10. Spare Parts List & CTN Overview For the latest spare part overview, please consult the Philips Service website. Table 10-1 Model numbers described in this manual: Styling Published in:...