Related Manuals for EVOC ec3-1813cld2na
Summary of Contents for EVOC ec3-1813cld2na
- Page 1 EC3-1813CLD2NA（B） 基于 Intel Luna Pier 平台 3.5 寸主板 3.5 ″ Motherboard Based on Intel Luna Pier Platform Version:C00...
-
Page 2: Copyright Notice
Trademarks EVOC is a registered trademark of EVOC Intelligent Technology Co., Ltd. Other product names mentioned herein are used for identification purposes only and may be trademark and/or registered trademarks of their respective companies. -
Page 3: Safety Instructions
Safety Instructions Please read this manual carefully before using the product; Leave the board or card in the antistatic bag until you are ready to use it; Touch a grounded metal object (e.g. for 10 seconds) before removing the board or card from the anti-static bag;... -
Page 4: Table Of Contents
Contents Chapter 1 Product Introduction..................1 Overview........................1 Mechanical Dimensions, Weight and Environment..........1 Typical Consumption ....................2 Microprocessor......................2 Chipset ........................2 System Memory .......................2 Display Function ......................3 Network Function ....................3 Audio Function ......................3 Power Feature ......................3 Expansion Bus ......................3 Watchdog Function ....................4 Operating System.....................4 On-board IO ......................4 Chapter 2 Installation....................5 Product Outline ......................5... - Page 5 Audio Connector ....................11 Serial Port ......................11 LPT Connector.......................12 SATA Connector ....................12 Hot-swap of SATA Hard Disk ................13 LAN Port........................15 USB Port ........................16 2-in-1 Keyboard/Mouse Connector................16 GPIO Connector.....................17 Status Control Connector on Front Panel ...............17 Power Connector....................18 CPU Fan Connector ....................18 CF Connector ......................19 PCI-104 Bus Expansion Connector................20 Chapter 3 BIOS Setup ....................24...
-
Page 6: Chapter 1 Product Introduction
It provides one DDR3 SO-DIMM slot and 1GB/2GB DDR3 memory on-board (EC3-1813CLD2NA(B)-N455/D425 provides 1GB memory on-board while EC3-1813CLD2NA(B)-D525 provides 2GB memory on-board); the maximum memory capacity supported by N455/D425 is up to 2GB while that supported by D525 is up to 4GB. It supports VGA, LVDS (18bit) display (Clone or expanded mode);... -
Page 7: Typical Consumption
1.8GHz) CPU on-board; internally integrates memory controller and graphics controller. Chipset Intel® N455/D425/D525 +Intel® ICH8M. System Memory The maximum memory capacity supported by N455/D425 is up to 2GB. It provides 1GB DDR3 memory on-board and one 204Pin DDR3 memory slot, supporting - 2 - EC3-1813CLD2NA(B) -
Page 8: Display Function
Integrated by Intel® N455/D425/D525 chip, assigning graphics memory according to requirement and supporting VGA+LVDS dual display function. EC3-1813CLD2NA(B)-N455: the maximum resolution supported by CRT is up to 1400x1050@60Hz; that supported by LVDS is 1280x800 or 1366x768. EC3-1813CLD2NA(B)-D525/D425: the maximum resolution supported by CRT is up to 2048x1536@60Hz;... -
Page 9: Watchdog Function
One PS/2 connector, brought out in 2-in-1 connector; One 8-bit digital IO connector, brought out in 2x5Pin header. Tips: how to identify the alarms 1. Long “beep” indicates system memory error; 2. Short “beep” indicates to power on the computer. - 4 - EC3-1813CLD2NA(B) -
Page 10: Chapter 2 Installation
Warning! Please adopt appropriate screws and proper installation methods (including board allocation, CPU and heat sink installation, etc); otherwise, the board may be damaged. It is recommended to use M3x6 GB9074.4-88 screws at H1 ~ H4. EC3-1813CLD2NA(B) - 5 -... -
Page 11: Locations Of Connectors
Chapter 2 Installation Locations of Connectors GPIO1 COM2 LPT1 JCC1 LAN1 COM3 COM4 LVDS1 LCDB1 PWR1 PWR2 SATA2 SATA1 - 6 - EC3-1813CLD2NA(B) -
Page 12: Structure
Tip: How to identify the first pin of the jumpers and connectors Observe the letter beside the socket: the first pin is usually marked with “1” or bold lines or triangular symbols; Observe the solder pad on the back; the square pad is the first pin. EC3-1813CLD2NA(B) - 7 -... -
Page 13: Jumper Setting
1-2 Short +3.3V 2-3 Short +5V(Default) JCF1 Note: this option is set to comply with different CF cards; as for the CF card without specified operating voltage, please choose the CF card voltage according to actual usage. - 8 - EC3-1813CLD2NA(B) -
Page 14: Display Connector
Please choose the VIO voltage according to the expansion device to be connected. The operating voltage of the expanded PCI devices shall be the same. Display Connector VGA Connector Signal Name Signal Name Green Blue VGA1 DDCDATA HSYNC VSYNC DDCCLK EC3-1813CLD2NA(B) - 9 -... -
Page 15: Lvds Backlight Control Connector
Bridge directly; the voltage amplitude is between 0V-3.3V while the duty cycle is between 0% ~ 100%); LCD_BKLTEN ---Backlight Enable, Active High. (The signal is output as CMOS output via North Bridge directly; the voltage amplitude is between 0V-3.3V). - 10 - EC3-1813CLD2NA(B) -
Page 16: Audio Connector
RS-232 mode. Signal Name COM2 COM1 ~ COM4 RS-232 RS-422 RS-485 DCD# TXD- Data- TXD+ Data+ COM1 RXD+ DTR# RXD- DSR# RTS# CTS# COM2 ~ COM4 Note: the data transmission direction is controlled automatically at RS-485 mode. EC3-1813CLD2NA(B) - 11 -... -
Page 17: Lpt Connector
The board provides one 2x13Pin LPT connector (Pitch: 2.00mm); the pin definitions are as follows: Signal Signal Name Name STB# AFD# ERR# INIT# SLIN# LPT1 ACK# BUSY SLCT SATA Connector The board provides two standard vertical SATA sockets. Signal Name SATA1/SATA2 - 12 - EC3-1813CLD2NA(B) -
Page 18: Hot-Swap Of Sata Hard Disk
Please carry out hot plugging as follows. Improper operation may destroy the hard disk or result in data loss. Hot Plug Step 1: Please plug the 1 x 4 pin SATA power connector (white) into the power adapter. EC3-1813CLD2NA(B) - 13 -... - Page 19 Hot Unplug Step 1: Uninstall the hard disk from the device manager. Step 2: Unplug the data cable from the SATA hard disk. Step 3: Unplug the SATA 15-pin power connector (black) from the SATA hard disk. - 14 - EC3-1813CLD2NA(B)
-
Page 20: Lan Port
The pin definitions are as follows: Signal Name Signal Name MX0+ MX0- MX1+ MX1- MX2+ MX2- MX3+ MX3- LINK_LED+ LINK_LED- LAN2 (SPEED100-) (SPEED1000-) (Pitch: 2.0mm) ACT_LED+ ACT_LED- EC3-1813CLD2NA(B) - 15 -... -
Page 21: Usb Port
2. The board provides one 2x5Pin (Pin9 is NC) USB port (Pitch: 2.0mm). Signal Name Signal Name USB1_Data- USB2_Data- USB1_Data+ USB2_Data+ 2-in-1 Keyboard/Mouse Connector The board provides one 2-in-1 keyboard/mouse socket. Signal Name KB_DATA MS_DATA KB_CLK MS_CLK - 16 - EC3-1813CLD2NA(B) -
Page 22: Gpio Connector
0-5V. Status Control Connector on Front Panel ATX Power Switch and HDD Indicator Connector (Pitch: 2.54mm) Signal Name Signal Name PWRBTN# RESET# HDD_LED- HDD_LED+ Power Indicator Connector (Pitch: 2.54mm) Signal Name PWR_LED+ EC3-1813CLD2NA(B) - 17 -... -
Page 23: Power Connector
PWR1 +12V 2. SATA Power Connector (Pitch: 2.5mm) Signal Name +12V PWR2 CPU Fan Connector The board provides one 1x3Pin CPU fan connector (Pitch: 2.54mm). Signal Name +12V CPUFAN1 FAN_IO Note: FAN_IO: fan speed impulse output. - 18 - EC3-1813CLD2NA(B) -
Page 24: Cf Connector
The board provides one standard CF card socket (CF1, on the rear of the board). Signal Name Signal Name CD1# CS0# CS1# VS1# ATASEL# IOR# IOW# CSEL# VS2# RESET# IORDY DREQ DACK# DASP# ATA66_DET WP/IOCS16# CD2# EC3-1813CLD2NA(B) - 19 -... -
Page 25: Pci-104 Bus Expansion Connector
+3.3V AD23 AD22 +3.3V IDSEL0 IDSEL1 IDSEL2 AD24 C/BE3# IDSEL3 AD26 AD25 AD29 AD28 AD27 AD30 AD31 REQ0# REQ1# REQ2# GNT0# GNT1# GNT2# CLK0 CLK1 CLK2 CLK3 PIRQD# RESET# +12V PIRQA# PIRQB# PIRQC# -12V REQ3# GNT3# - 20 - EC3-1813CLD2NA(B) - Page 26 Set the models of the primary display and the secondary display in “Primary Display” and “Secondary” successively. After that, click “Apply” and then the two displays will adjust the desktop. The primary display will show the following information: EC3-1813CLD2NA(B) - 21 -...
- Page 27 “Intel Graphics Media Accelerator Driver” control software and the following interface will appear. Click “multi-screen display”, a set of options will appear on the right; choose “Operating Mode” and then “Extended desktop” in the drop down list: - 22 - EC3-1813CLD2NA(B)
- Page 28 Set the models of the primary display and the secondary display in “Primary Display” and “Secondary” successively. After that, click “Apply” and then the two displays will adjust the desktop. The primary display will show the following information: Click “OK” and the dual display extended mode is set. EC3-1813CLD2NA(B) - 23 -...
-
Page 29: Chapter 3 Bios Setup
BIOS to restore the normal operation of system. Our company is constantly researching and updating BIOS, so the setup interface may be a bit different. The figure below is for reference only; it may be different from your BIOS setting procedure in use. - 24 - EC3-1813CLD2NA(B) -
Page 30: Basic Function Setting For Bios
Choose this option and set the current date by < + > / < - >, which is displayed in the format of month/date/year. Reasonable range for each option is: Month (Jan.-Dec.), Date (01-31), Year (Maximum to 2099), Week (Mon. ~ Sun.). EC3-1813CLD2NA(B) - 25 -... - Page 31 + - Change Field Cache L1; :48 KB Tab Select Field Cache L2; :1024KB General Help F10 Save and Exit Ratio Actual Value ESC Exit Hyper Threading Technology [Enabled] Intel(R) SpeedStep(tm)tech [Enabled] V02.61 (c)Copyright 1985-2006, American Megatrends, Inc. - 26 - EC3-1813CLD2NA(B)
- Page 32 AHCI Port1 [Not Detected] AHCI Port2 [Not Detected] V02.61 (c)Copyright 1985-2006, American Megatrends, Inc. ATA/IDE Configuration This option is used to configure the operating mode of ATA; there are two options for this item: Compatible and Enhanced. EC3-1813CLD2NA(B) - 27 -...
- Page 33 Used to set whether to enable S.M.A.R.T function and it is only effective for the hard disk supporting this function. *32Bit Data Transfer This option is used to enable 32-bit hard disk accessing mode, which could optimize hard disk read and write speed. - 28 - EC3-1813CLD2NA(B)
- Page 34 Serial Port3 IRQ [IRQ3] Serial Port4 Address [2E8] Serial Port4 IRQ [IRQ3] Parallel Port [378] Parallel Port [Normal] Parallel Port [IRQ7] V02.61 (c)Copyright 1985-2006, American Megatrends, Inc. Onboard Floppy Controller Used to enable the floppy driver controller. EC3-1813CLD2NA(B) - 29 -...
- Page 35 V02.61 (c)Copyright 1985-2006, American Megatrends, Inc. System Temperature Current system temperature, it is monitored by thermal resistor on motherboard. CPU Temperature Current CPU temperature, it is monitored by temperature sensors on motherboard. CPUFAN1 Current speed of CPUFAN1. - 30 - EC3-1813CLD2NA(B)
- Page 36 This option is used to support legacy USB devices (keyboard, mouse and storage device, etc.); when this option is set to Enabled, the USB device could be used even if under OS that doesn’t support USB, such as DOS. EC3-1813CLD2NA(B) - 31 -...
- Page 37 This option is used to enable or disable the system clock. When the specified time is expired, it will wake the system from power saving mode, even from power off mode. This function shall be supported by ATX power. - 32 - EC3-1813CLD2NA(B)
- Page 38 Enter Go to Sub Screen Boot Display Device [CRT+LVDS] General Help Flat Panel Type [800X600/S/18/G104S] F10 Save and Exit UserDefine Panel Type [Disabled] ESC Exit SouthBridge Configuration Onboard Audio Controller [Enabled] V02.61 (c)Copyright 1985-2006, American Megatrends, Inc. EC3-1813CLD2NA(B) - 33 -...
- Page 39 User Define, users may configure the flat panel type according to user define. UserDefine Panel Type This option is used for the resolution of user-defined Panel. Onboard Audio Controller Select whether to enable the audio card controller. - 34 - EC3-1813CLD2NA(B)
- Page 40 Quiet Boot [Disabled] General Help Waite For ‘F1’ If Error [Enabled] F10 Save and Exit Boot Device Priority ESC Exit Boot from Embedded WinCE [No] Boot Device [Network:B01 D00 ReaLtek PXE] V02.61 (c)Copyright 1985-2006, American Megatrends, Inc. EC3-1813CLD2NA(B) - 35 -...
- Page 41 Disabled: disable the protective function for MBR virus. Manual: when MBR virus is detected in the storage device, whether to prompt the users to clear the virus. Quiet: when MBR virus is detected in the storage device, delete the virus directly. - 36 - EC3-1813CLD2NA(B)
- Page 42 To implement this function, choose this option and press < Enter >; messages to be confirmed will be shown on the screen, press < Enter > to implement this function. EC3-1813CLD2NA(B) - 37 -...
-
Page 43: System Resource Managed By Bios Under X86 Platform
The table below shows the I/O address assignments for part of the devices of the CPU card. As the address of PCI device (e.g. PCI network card) is configured by software, it is not listed in this table. - 38 - EC3-1813CLD2NA(B) - Page 44 DMA Controller #4 089h - 08Bh Carrier Resource 08Ch - 08Eh DMA Controller #5 08Fh Carrier Resource 090h - 09Fh 0A0h - 0A1h Programmable Interrupt Controller #2 0A2h – 0BFh Carrier Resource DMA Controller #6 0C0h - 0DFh EC3-1813CLD2NA(B) - 39 -...
- Page 45 Only the ones that are not occupied can be assigned to other devices. ISA device requests exclusive use of its interrupt. Only the plug and play ISA devices can be assigned by the BIOS or the OS. And several PCI devices share one interrupt, - 40 - EC3-1813CLD2NA(B)
- Page 46 IRQ4 COM1/ COM2 IRQ5 Reserved IRQ6 Reserved for Floppy Drive Controller IRQ7 Reserved IRQ8 System CMOS/Real Time Clock IRQ9 ACPI IRQ10 Reserved IRQ11 Reserved IRQ12 PS/2 Mouse IRQ13 Numeric Data Processor IRQ14 Primary IDE IRQ15 Reserved EC3-1813CLD2NA(B) - 41 -...
-
Page 47: Chapter 4 Installing The Drivers
Chapter 4 Installing the Drivers Chapter 4 Installing the Drivers Regarding the driver program of this product, please refer to the enclosed CD. - 42 - EC3-1813CLD2NA(B) -
Page 48: Appendix
Appendix Appendix BPI Overview EVOC BPI (BIOS Programming Interface) is a cross-platform, easy-maintenance software interface specification, which can access hardware under the protection mode of the operating system. The function of the product is to provide a unified standard interface for the application software or driver; therefore, when the hardware of the motherboard is upgrading, there is no need to modify the application software or driver and the former software can operate on the new platform normally. - Page 49 Appendix 5、 Low Cost Developing the applications by BPI will not increase additional hardware and software cost, but it will reduce the development difficulty, development cycle and time-to-market for the system integrator. - 44 - EC3-1813CLD2NA(B)
-
Page 50: Troubleshooting And Solutions
Analysis: the data cable of the hard disk may get knocked EC3-1813CLD2NA(B) - 45 -... - Page 51 OK. Re-install detected. the device driver and check whether it can be recognized; check whether the device is normal; if the device is normal, then check whether the device is compatible with the motherboard. - 46 - EC3-1813CLD2NA(B)
Need help?
Do you have a question about the ec3-1813cld2na and is the answer not in the manual?
Questions and answers