Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Burmester 102
Summary of Contents for Burmester 102
- Page 1 OWNER´S-MANUAL CD-PLAYER HIGH END MADE IN GERMANY...
- Page 2 VERSION: 1.0 from December, 17 2011...
- Page 3 Dear Audiophile, Thank you for choosing this Burmester audio component. We sincerely appreciate your trust in us. You have purchased a unit which excells in musical fidelity and combines uncompromising manufacturing quality with technical innovation and the highest degree of operating flexibility.
-
Page 4: Table Of Contents
C O N T E N T S INTRODUCTION UNPACKING AND INSTALLATION FRONT AND REAR VIEW OF THE 102 The Front Panel The Rear Panel THE REMOTE CONTROL FREQUENTLY ASKED QUESTIONS TROUBLESHOOTING GETTING STARTED CONNECTIONS Digital Output Digital Input Analog Outputs... -
Page 5: Introduction
For the cleanest power supply we recommend our triple-shielded power cord Burmester- POWER. IR receiver The IR receiver receives signals from the Burmester remote control and must not be covered up by any objects. Heat development Be careful when touching the housing – it may get quite warm during operation. - Page 6 Reset If the unit does not react when pressing the control keys on the front panel it may be reset to normal operation by switching it off and back on using the AC mains switch in the back. Lightening strikes During the summer months, malfunctions often occur due to voltage spikes in the power lines after lightning strikes.
-
Page 7: Unpacking And Installation
UNPACKING AND INSTALLATION CAUTION: The CD player 102 is shipped inside a plastic protective cover. Make sure that children do not play with it to avoid the danger of suffocation. Unpacking To avoid damaging the housing, please do not use pointed or sharp tools to open the box. -
Page 8: Front And Rear View Of The 102
FRONT AND REAR VIEW OF THE 102 THE FRONT PANEL CD tray STOP button PROGRAM LED illuminates when a music program (10) PLAY/PAUSE button has been selected and saved (11) Power LED TRACK display indicates the current track (12) OPEN/CLOSE button for opening/closing the... -
Page 9: The Rear Panel
THE REAR PANEL (16) BURLINK interface RS-232 with check LEDs (23) Analog audio output (unbalanced) (17) BURLINK interface USB with check LEDs (24) Analog audio output (unbalanced) (18) AC mains switch for analog recording unit (19) AC mains terminal (25) Digital audio output RCA (75 (20) REMOTE output jack... -
Page 10: The Remote Control
THE REMOTE CONTROL All functions of the 102 may be controlled by remote. Just point the remote directly at the IR sensor (6) and press the according buttons. NUMERICAL buttons for a direct choice of POWER button tracks switches the... - Page 11 To navigate through the menu and select different options you may use the buttons ► ◄ ▲ ▼ and OK on the remote control of the 102. For details about using the menu please refer to the chapter SETUP MENU.
- Page 12 TORX or the internal CD drive. The alphanumeric display will show the selected input. Input selecting with the STATION keys is only possible, when the menu item RC-I in the SYSTEM SETUP is set to ON. All other keys of the remote control have no functions with respect to the 102 CD-Player.
-
Page 13: Frequently Asked Questions
The balcanced output (22), as well as the unbalanced outputs (23, 24) can be connected to a preamplifier and a integrated amplifier. Both of the 102’s digital outputs can be connected to devices with digital inputs. Thereby, both of the digital outputs are delivering the data of the selected digital input. -
Page 14: Troubleshooting
After the CD has been read-in, “NO CD” is shown in the display: The 102 CD-Player is only capable of reproducing audio CDs. If you insert a CD, which the CD can not read, the message „NO DISC“ is shown in the display. -
Page 15: Getting Started
The device is now in standby mode. Now you can switch the CD-Player on using the POWER button (15) on the front panel. • The following chapters of this Owner’s Manual will provide detailed instructions about the extraordinary possibilities and capabilities of the 102 CD-Player. -
Page 16: Connections
CONNECTIONS The connections of the CD-Player 102 are located on the rear panel of the device. During the connecting procedure all individual components of your playback system must be turned off. There are various possibilities to connect the CD player, depending upon the kind of audio components and auxiliary devices used. -
Page 17: Analog Outputs
052. In this case, 052 has the master function. Connecting DC IN (21) to the corresponding DC OUT-jack of another Burmester-unit offers to switch on or off the 102 simultaneous by the other unit. In this case, 102 has the slave function. BurLink To the BURLINK interface plugs (16), (17) a computer system e.g. -
Page 18: Operation And Control Features
READING). After the reading process, the display shows the number of tracks as well as the total playing time of the CD. If there is no CD in the CD tray, or the inserted CD is incompatible with the 102, the display will show the message NO DISC. -
Page 19: Display
Display When the internal CD transport is selected and a CD is playing, the alphanumeric display shows the current track of the CD in the TRACK display (3) and the playing time in the TIME display (4). The TIME display can be switched to - lapsed time of the current track - remaining time of the current track - lapsed time of the CD... -
Page 20: Setup Menu
SETUP MENU The SYSTEM SETUP menu of the CD player 102 allows the easy programming of certain basic settings. All settings of the SYSTEM SETUP will be saved automatically after leaving the SETUP and remain after switching off the unit. - Page 21 AUTO You can choose, if the CD player should start playback directly after switching on the unit or after closing the CD tray. The unit reads only the table of content and remains in STOP mode. The unit begins playing the CD directly after switching on. You can choose, if the type and the serial number of the unit will be shown in the alphanumeric display after switching on the player.
-
Page 22: Programming A Favourite Track Selection Of A Cd
PROGRAMMING A FAVOURITE TRACK SELECTION OF A CD A total of 50 tracks from a CD can be programmed for playback in a selected order. Programming can only be done using the remote control. The program plays the tracks in the selected order. Activation To start the program function press the button PROGR. -
Page 23: Burlink
Before using the USB port the appropriate drivers must be installed. The software for the USB port is compatible with the operating systems WINDOWS 2000 and WINDOWS XP. COMMANDS Following are listed the possible commands to control the CD player 102. All commands needs to be sent in capital letters finished with a “carriage return“ \r . POWON\r... -
Page 24: Technical Specifications
This unit contains a CLASS 1 LASER PRODUCT inside. Do not look into the laser light, when the unit is powered up. BURMESTER AUDIOSYSTEME GMBH – WILHELM-KABUS-STRAßE 47 – 10829 BERLIN TEL 030/78 79 68 0 – FAX 030/78 79 68 68...