Using The Rangehood; Maintenance And Cleaning - Electrolux EFC925SAR User Manual

10

USING THE RANGEHOOD

Fan
Standby mode
When connecting the hood to the power supply for the
first time or after power is returned after power outage, all
symbols on the control panel will light up from left to right
and a "beep" will sound once. Following this, the control
panel goes to standby mode and the hood will be ready
for use.
Turning on hood
When the hood is in standby mode, user can either press
the or button to turn on the fan or light individually.
The default factory level is 2, following that, the hood
remembers the last used setting and will start at that level
when the user presses the fan or light button. Pressing
directly on the slider strip will also allow the user to jump
straight into the level pressed.
Fan – select speed to suit cooking conditions.
– motor on/off
1 – light frying/boiling
2 – frying/wok cooking/heavy boiling
3 – grilling, intensive frying and wok cooking
– stir frying
NOTE: Touch the symbol to turn the fan boost ON, the
fan boost starts running at the highest fan speed for 1
minute before reducing to speed 3 automatically.
Light – select light level
– Light on/off
1 – low-light level
2 – mid-light level
3 – high-light level
Using the Timer
At the end of cooking, if the timer is switched on, the
rangehood will continue to run for an additional 5 minutes,
depending on the selected fan speed. This should ensure
the removal of any odours that remain after cooking.
Light
Filter
This is the indicator/switch to show when the filter needs
to be cleaned. Once the filters are cleaned the "Filter" alert
can be deactivated with a single touch.
Control Lock
Press and hold 3 seconds the . button will lock the
control panel at any time. The same action will unlock the
control panel.
When control is locked, pressing any other button will
make . button blink and a beep will sound.
• When the hood is working (light on and fan on) and
is touched then hood will stop fan but keep lighting on
while lock menu.
• When the hood is working (lights off and fan on) and
the is touched then hood will stop fan and keep
lighting off while lock menu.
• When is activated when hood is working it will just
change the status of fan motor and not change the
status of lighting.
• When is touched while hood stops then it will just
lock the menu

MAINTENANCE AND CLEANING

CAUTION!
• Before maintenance or cleaning is carried out,
the canopy rangehood should be disconnected
from the main power supply. Ensure that the
rangehood is switched off at the wall socket and
S
the plug removed.
• External surfaces are susceptible to scratches
and abrasions, so please follow the cleaning
instructions to ensure the best possible result is
achieved without damage.
• These instructions must be followed to avoid a
risk
Stainless Steel Surface
Clean stainless steel surfaces using non-abrasive cleaning
products that are specifically for use on stainless steel. To
ensure best results also use an even pressure and follow
the grain of the stainless steel. Use of a soft cloth reduces
the risk of scratching. If the cloth is wet ensure that a dry
soft cloth is used to wipe down the surface again reducing
the risk of any surface rust appearing.
Control panel surface
The control panel can be cleaned using warm soapy
water. Ensure the cloth is well wrung before cleaning. Use
a dry soft cloth to remove any excess moisture left after
cleaning.
Removing the metal grease lters
Push the grease filter towards the left side of the unit and
then pull it down.
Hand washing
The mesh filters can be cleaned by hand in warm soapy
water. Soak in warm water and some washing up liquid.
For stubborn grease stains use a soft nylon brush to help
remove these stains. After cleaning ensure that the filters
are completely dry before refitting.
Dishwasher
Place grease filters in the dishwasher. Select the most
powerful washing program and highest temperature, at
least 65°C. Repeat the process. Refit the grease filters
when they are dry. When washing the metal grease filter
in the dishwasher a slight discolouration of the filter can
occur, this does not have any impact on it's performance.
Changing the lamps
Lamps are long life LED lamps and should not require
service. If there is an issue with lamps please contact
Service. Service contact details shown on page 13.
Charcoal lter
• The charcoal should only be used if you want to
use the hood in the recirculation function.
• This cannot be cleaned or re-used and as a
general rule, the activated charcoal filter should be
changed once every four months.
Open or fit the charcoal filter as shown in the image below.
• Always specify the hood model code number and
serial number when ordering replacement filters. This
information is shown on the registration plate located
on the inside of this unit.
• Replacement charcoal can be ordered from your
local Spare parts centre, contact details are shown on
page 13.
11