Uplink 4530EX Installation Manual

Uplink 4530EX Installation Manual

4g primary cellular alarm communicator
Hide thumbs Also See for 4530EX:

Advertisement

®
FOR SALES, PRODUCT
INFORMATION &
TECHNICAL SUPPORT
Uplink Security, LLC.
3330 Cumberland Blvd.
Suite 700
Atlanta, GA 30339
1-(888) 9-UPLINK, 1-(888)-987-5465
Fax 1-(888)-542-9105
sales@uplink.com
www.uplink.com
4G PRIMARY CELLULAR
ALARM COMMUNICATOR
INSTALLATION
USER'S GUIDE
®
4530EX
&

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4530EX and is the answer not in the manual?

Questions and answers

Summary of Contents for Uplink 4530EX

  • Page 1 ® ® 4530EX 4G PRIMARY CELLULAR ALARM COMMUNICATOR INSTALLATION FOR SALES, PRODUCT & INFORMATION & USER’S GUIDE TECHNICAL SUPPORT Uplink Security, LLC. 3330 Cumberland Blvd. Suite 700 Atlanta, GA 30339 1-(888) 9-UPLINK, 1-(888)-987-5465 Fax 1-(888)-542-9105 sales@uplink.com www.uplink.com...
  • Page 2: Table Of Contents

    I. Default Event/Email Messages ............23 J. Completing the Installation and Testing ........23 Specifications ..................25-26 © 2013 Uplink Security, LLC. All rights reserved. Uplink is a trademark of Uplink Security, LLC. Appendix A: Contact ID, SIA, Modem IIe/IIIa/IIIa Event Codes .....27-28 No part of this publication may be reproduced or used in any form without permission Appendix B: 4530EX Default Event Codes ..........29...
  • Page 3: Introduction

    Once the 4530EX completes a communications session with the alarm panel, it will transmit the alarm information using the local GSM cellular communications network.
  • Page 4: Key Features

    KEY FEATURES (cont.) A. FULL DATA Reporting. Compatible with most alarm panels using Contact ID (SIA G. Automated Testing. The 4530EX can be programmed to send an automated test signal DC-05 Standard), SIA FSK Level 1 (SIA DC-03 Standard), Modem IIe/IIIa/IIIa to the central station on a monthly, weekly or daily interval.
  • Page 5: Warranty & Limitation Of Liability

    Uplink. Uplink’s warranty does not extend to end NOT IN PRIVITY OF CONTRACT WITH UPLINK ARISING OUT OF OR RELATED user consumers of Uplink products or to other parties not in privity of contract with Uplink TO AN UPLINK PRODUCT AND/OR SERVICE, WHETHER ARISING OUT OF OR...
  • Page 6: Fcc Rf Exposure Information

    4G PRIMARY CELLULAR ® 4530EX ALARM COMMUNICATOR FCC & INDUSTRY CANADA FCC RF EXPOSURE INFORMATION REGULATORY COMPLIANCE In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety...
  • Page 7: Technical Support

    S4 and move the unit to a location that gives him the best signal strength.) Uplink Security, LLC. b. Proximity to the alarm panel and where to route the 4530EX’s relay output 3330 Cumberland Blvd. that connects to an alarm panel input.
  • Page 8: Leds

    RSSI Mode: When the 4530EX is placed in Received Signal Strength Indicator Normal Mode: Upon initial power up, the 5 LEDs on the 4530EX will begin to (RSSI) Mode by turning Dipswitch S4 to ON, the five LEDs indicate the follow...
  • Page 9: Locating And Installing The 4530Ex

    INSTALLATION (cont.) D. Locating and Installing the 4530EX The 4530EX is housed in a plastic enclosure. The installer needs to supply DC power from the panel via the AUX output, or battery, via a separate DC power source. Input DC current is listed on page 25.
  • Page 10: Connecting The 4530Ex To The Alarm Panel

    3. Output Block OTA Config Normal Operations Reserved The 4530EX has one relay output that can be used to activate an input on the TO RJ31X Normal Operations RSSI Measurements alarm panel or for other local purposes. Decide on how to use this output (see section 6.
  • Page 11: Configuring Input 1

    Input 1 if Standard Type Input 1 can be configured to perform one of four functions and is programmable Over- The-Air via the Uplink Dealer web site. 1. Standard Input - (Default mode) This mode configures the unit to be tripped from a DC voltage ranging from 9 V DC to 12 V DC or an open collector.
  • Page 12: Activating The 4530Ex

    4. Output Relay 1 Mapping (Default = #1 Loss of Cellular Service) Agreement”. There are 6 Trouble states that can be declared by the 4530EX, and each of 4. Enter the device serial number and select “Activate”. these states can be programmed from the dealer website to activate the 5.
  • Page 13: Default Event/Email Messages

    4530EX that can be sent to the central station receiver. See Appendix B for a list of the default event codes transmitted by the 4530EX. The 4530EX supports Pulse 4/2 with any combination of :10, :20, or :40 PPS. Two round or checksum, 1400 Hz or 2300 Hz handshake.
  • Page 14 4G PRIMARY CELLULAR ® 4530EX ALARM COMMUNICATOR SPECIFICATIONS SPECIFICATIONS (cont.) DIGITAL DIALER INTERFACE RADIO Format Compatibility Contact ID, SIA, Modem IIe/IIIa/IIIa , Pulse Frequencies 850/1900 MHz 4/2 (:10, :20, or :40 PPS) Sensitivity -106 dB (typical) Connector RJ45 and screw terminals...
  • Page 15 MODEM II /III /III CODES (cont.) Following is a list of event codes that can be sent to the central station receiver for events generated by the 4530EX: EVENT DESCRIPTION CONTACT ID SIA DC-03 MODEM IIe/ EVENT CODE EVENT CODE...
  • Page 16: Appendix B: 4530Ex Default Event Codes

    UPLINK 4530EX 4G PRIMARY ALARM COMMUNICATOR 4530EX DEFAULT EVENT CODES INSTALLATION, OPERATION AND PROGRAMMING GUIDE © 2013 Uplink Security, LLC. All rights reserved. Uplink is a trademark of Uplink The 4530EX is defaulted to send both the Alarm/Trouble condition and the Restoral Security, LLC.

Table of Contents