Sony XAV-602BT Service Manual page 5

NOTE THE MAIN BOARD OR SYSTEM CONTROLLER
(IC502) REPLACING
When the complete MAIN board or system controller (IC502) is
replaced, the destination setting is necessary.
Note: Remote commander is necessary.
1. Preparing the Destination Setting
Be sure to solder the SL501 on the MAIN board before doing the
destination setting.
– MAIN Board (Component Side) –
SL501
2. Destination Setting
Set destination according to the procedure below.
2-1. Setting the Destination Code
1. In the state of source off (Home screen is displayed), enter the
destination setting mode by pressing the buttons in order of
the [4] t [5] t [6] on the remote commander (press only
the [6] button for two seconds).
2. The following screen is displayed and the destination setting
mode becomes effective.
(Displayed characters/values in the following fi gure are ex-
ample)
Note: Refer to following "2-2. Entering the Destination Code" for opera-
tion method.
<DESTINATION SETTING>
0 0 0 0 0 2
EUR 000000
UC 000001
E17(P3E) 000002
E(N4E) 000003
RU2(P5EUR) 000004
3. The resetting operation is executed by pressing the [OFF] but-
ton on the remote commander the setting ends, and the unit
returns to the normal condition.
2-2. Entering the Destination Code
Note: Input of the destination code cannot be performed by the keys of
main unit. Be sure to input the destination code by remote com-
mander.
• Method of operation by remote commander
IC502
MECHA(EUR) 000006
FT(JPN) 000007
BR(N4E) 000008
EA 00000A
EJ(EUR) 00000B
Note: The ten key cannot be used.
1. Press the [ ] or [ ] button, and select the alphanumeric char-
acter of "0 to F".
2. The digit advances by pressing the [
The digit returns by pressing the [
3. The setting is completed by pressing the [ENTER] button, and
the initialization operation is done.
2-3. Destination Code
Destination
US and Canadian models
AEP and UK models
Russian model
E (NTSC) model
E (PAL) model
Indian model
3. Confi rmation After Destination Setting
Execute the following operation after completing the destination
setting, and confi rm a correct destination was set.
Destination setting checking method:
1. In the state of source off (Home screen is displayed), enter the
test mode by pressing the buttons in order of the [4] t [5] t
[0] on the remote commander (press only the [0] button for two
seconds).
2. The following screen is displayed and confi rm that item of the
destination has been rewritten correctly.
(Displayed characters/values in the following fi gure are ex-
ample)
<TEST MODE>
1. Audio FACTORY MODE
2. Audio DEBUG MODE
4. Visual FACTORY MODE
Temperature : 0x105
5. ENGINEER MODE
Tag : 0/50
6. DESTINATION MODE
7. Service Mode
AVC Ext NAVI
8. MECHA MODE
9. NAVI/RGB-OUT MODE
Master: BA08
Mecha: XR04
BT Module: 4000
Display: SA08
Pandora ID: BB4E78D7
3. The resetting operation is executed by pressing the [OFF] but-
ton on the remote commander the confi rming ends, and the
unit returns to the normal condition.
4. Processing After the Destination Setting
Be sure to unsolder the SL501 on the MAIN board after doing the
destination setting.
– MAIN Board (Component Side) –
SL501
XAV-602BT
] button.
] button.
Desitination code
000601
000600
000604
000603
000702
000705
Bluetooth
Navigation:
Destination: E17_E3P
Region: 0
AP : BB07
IC502
5