Tuning The Tv To Your Vcr; Storing Tv Broadcasts In Your Vcr - Panasonic NV-MV21GN Operating Instructions Manual

Tuning the TV to Your VCR

The VCR supplies a signal to the TV via the RF coaxial cable
on channel NZ21-69 or AU28-69.
If you have connected the VCR to the TV through the Audio/
Video input sockets, then you do not need to follow the
procedure below. To view the pictures from the VCR, set to
the AV mode on the TV with [AV] (2).
Preparation
• Turn on the TV and the VCR.
Operations
1 Hold down [MENU] (9) for 5 seconds or more.
2 Set the TV to an unused position which you wish to
use for your video playback.
• Tune the TV until the display shown below appears on
the screen. (Please refer to the TV manufacturers
operating instructions regarding tuning.)
Panasonic VCR
END: MENU
3 Press [MENU] (9).
To Change the RF output Channel
You can change the RF output channel, for example, when
interference occurs on the picture after tuning.
Operations
1 Hold down [MENU] (9) for 5 seconds or more.
• The VCR display changes as shown below and the VCR
picture on the TV displays this pattern.
Panasonic VCR
END: MENU
2 Enter the desired channel number (NZ21-69, AU28-69)
by [Numeric] (3) or [Channel] (20).
• Set the RF output channel of the VCR to [ss] (RF OFF) when
the VCR is connected to the TV via the Audio/Video cable.
Press [Channel] (20) to display [ss].
For New Zealand
...
21E
69E
(RF OFF)
• It is also possible to select by pressing [Numeric] (3).
Example:
2
28:
3 Press [MENU] (9) to finish the setting mode.
4 Retune your TV to the new RF channel for the VCR.
Note:
• Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
For Australia
... ...
28 37 69
(Initial position)
ss
8

Storing TV Broadcasts in Your VCR

The VCR is fitted with its own tuner (just like a normal TV) and
can be preset to receive up to 99 TV broadcast stations.
Pre-programmed TV Channels
(Australia only)
The local TV broadcast channels 2, 7, 9, 10 and 28 are
factory-preset in this VCR.
That is, if you can receive television broadcasts on VHF
channels 2, 7, 9, 10 and UHF channel 28, these are already
tuned on the programme positions with the matching numbers.
However, it is possible to cancel these settings and tune the
local TV broadcast channels to any desired programme position.
Auto Tuning Using the On Screen Display
For New Zealand
When you use this VCR in New Zealand, need to operate as
follows.
Preparations
• Confirm that the TV is on and the VCR viewing channel is
selected.
• Turn on the VCR and select any programme position except
AV.
Operations
1 Press [MENU] (9) to display the
Main menu on the TV screen.
2 Press [43] (28) to select
[TUNER PRESET] then press
[ENTER] (26).
3 Press [43] (28) to select
[COUNTRY] then press [2 1]
(28) to select [NEW ZEALAND].
4 Press [43] (28) to select
[AUTO TUNE] then press [2 1]
(28) to start the Auto Tuning.
• When Auto Tuning is completed,
the On Screen Display
disappears and programme
position 1 is selected.
Channels that can be received
VHF
New Zealand 1-11
Notes:
• Auto Tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned programme
position. Other programme positions are skipped.
• Auto Tuning takes 5 or more minutes to complete its search.
5
MENU
CLOCK SET
TUNER PRESET
SYSTEM
OPTION
TAPE REFRESH
NAVI MEMORY 0PROG.
SELECT : , ENTER
END : MENU
MENU
CLOCK SET
TUNER PRESET
SYSTEM
OPTION
TAPE REFRESH
NAVI MEMORY 0PROG.
SELECT : , ENTER
END : MENU
TUNER PRESET
CH 1
[ OFF ]
CLEAR
COUNTRY NEW ZEALAND
[ ]
AUTO TUNE
SEARCH [ 3 ]
FINE
SELECT: END : MENU
TUNER PRESET
CH 1
OFF
[ ]
CLEAR
COUNTRY [ NEW ZEALAND ]
AUTO TUNE
SEARCH [ 3 ]
FINE
SELECT: END : MENU
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 1 SEARCH 100
END : MENU
The number displayed here
is the number of channels
still to be auto tuned.
UHF CATV
21-69 44-470 MHz