Table of Contents
Advertisement
Before you start
Functional overview (cont'd)
Installing batteries in the remote control
Install two AA batteries (supplied) matching the
polarity indicated inside battery compartment of the
remote control.
1
2
3
Note:
Incorrect use of batteries can result in hazards such
as leakage and bursting. Please observe the following:
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together,
although they may look similar, different batteries
may have different voltages.
• Make sure that the plus and minus ends of each
battery match the indications in the battery com-
partment.
• Remove batteries from equipment that is not going
to be used for a month or more.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction's rules that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or disas-
semble batteries.
Using a remote control
Keep in mind the following when using the remote
control:
• Make sure that there is no obstacle between the
remote control and the remote sensor on the
DVD recorder.
• Use within the operating range and angle as
shown.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the
remote sensor of the DVD recorder.
• Remote control for different devices can interfere
with each other. Avoid using remote control for
other equipment located close to the DVD
recorder.
• Replace the batteries when you notice a fall off in
the operating range of the remote control.
Within about
REC
REC
MODE
23feet (7m)
60˚
Remote
control
Guide to On Screen Menus
The DVD recorder uses the following on screen menu for most operations. SETUP/DISC/CD menu,Title
list, and DISPLAY menu, which allows you to change the playing status of disc during play.
The DISPLAY menu also gives you some disc information for checking the status of the disc.
SETUP/DISC/CD menu
Press SETUP button to display the setup main menu, then choose either of SETUP/DISC/CD by K / L / { / B
button.Then, press ENTER button to display each menu.
These menus provide entry to all main functions of the DVD recorder.
"SETUP" is available only in the
Stop mode.
Setup Menu
Setup
1
2
4
5
Playback Setting
1. Playback:
To set up the DVD recorder to
play discs as you prefer.
2. Recording:
To set up the DVD recorder to
record to discs as you prefer.
3. Display:
To set up the OSD screen and the
front display of the DVD recorder
as you prefer.
4. Select Video:
To choose a line input to record
to DVD discs from other video
equipment.
5. Clock:
To set up the clock of the DVD
recorder as you need.
6. Channel:
To adjust the channel setting of
the DVD recorder as you prefer.
9
10
Before you start
Functional overview (cont'd)
"DISC" is available only when a DVD-R/RW disc is
inserted into the DVD recorder. When playing back
a DVD-Video disc (commercially available) or the
finalized DVD-R disc, you cannot select "DISC".
Disc Setting
Disc
Edit
Format
3
Finalize
Disc Protect OFF
ON
1 2 3 4
6
1. Edit:
1. Random Play:
Turns on a title list, (When a disc
To activate the random playback
with VR mode is inserted,
feature.
'Original' or 'PlayList' is available.),
2. Program Play:
which shows the recorded titles
To activate the programmed play-
on the disc.
back feature.
2. Format:
3. PBC (Video CD only):
Allows you to erase all of the
To turn the PBC function on or
recorded content on the disc.
off.
The disc will be completely blank.
3. Finalize:
Allows you to finalize a disc con-
taining recorded titles.
4. Disc Protect
(VR mode only) :
Allows you to protect a disc from
accidental editing or recording.
"CD" is available only when an
Audio CD disc,Video CD disc or
CD-R/RW disc with MP3 files is
inserted into the DVD recorder.
CD Playback Mode
CD Playback Mode
Random Play
Program Play
PBC(Video CD only)
ON
1 2 3
Advertisement
Table of Contents
