Sony HCD-HPX9 Service Manual page 54

HCD-HPX9
Ver. 1.6
QQ
3 7 63 1515 0
[CD SHIP MODE]
This mode can run the CD sled motor optionally. Use this mode, for
instance, when cleaning the optical pick-up.
Procedure:
1. Press the @/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press two buttons of [EX-CHANGE] and @/1 simultaneously.
*1
4. Set to the CD ship mode. (chucking on)
5. After blink "STANDBY", "LOCK" is displayed, disconnect
the AC plug.
*1) If press three buttons of [DISC SKIP], [EX-CHANGE] and
[PLAY MODE/TUNING MODE] simultaneously, Activate the
CD ship mode and MC cold reset.
[CD SLOT LOCK]
This mode is for the antitheft of CD disc in shop. (not for transport)
Procedure:
1. Press the @/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Insert a disc.
4. While pressing the x button, press the A button for more 5
seconds.
5. The message "LOCKED" is displayed and the disc slot is
locked. (Even if exiting from this mode, the disc slot is still
locked)
6. If press the A button to eject the disc, the message
"LOCKED" is displayed and can not eject the disc.
7. To release this lock, while pressing the x button, press the
A button for 5 seconds again.
TE
L 13942296513
8. The message "UNLOCKED" is displayed and the disc slot is
unlocked.
[CD ERROR CODE DISPLAY MODE]
This mode can be used for error code display of CD section.
Procedure:
1. Press the @/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD functuion.
3. Press three keys of x , [DSGX] and X TAPE simultaneously.
4. When this mode is activated, mechanism deck error code is
displayed on the fluorescent indicator tube.
5. Press the m (remote commander) or M (remote
commander) button to changed over between optical pick-up
error code display mode and mechanism deck error code mode.
6. Press the . (remote commander) or > (remote
commander) button to change over display of error history.
[CD SERVO TEST MODE]
This mode used to check operation of optical pick-up.
Procedure:
1. Press the @/1 button to turn the power ON.
2. Press the [FUNCTION] button to select CD functuion.
3. Press three keys of X TAPE , x and [DISC 1] simultaneously.
4. When the CD servo test mode is activated. In this state each
time [DISPLAY] button of remote commander is pressed,
tracking ON/OFF switch is performed.
5. To release this mode, press the @/1 button.
www
.
54
http://www.xiaoyu163.com
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
[CD POWER MANAGE]
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the @/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press the @/1 button again to turn the power off (standby).
4. While pressing the x button, press the @/1 button.
5. It turns power on and display "CD POWER", then display
"ON" or "OFF".
[CHANGE-OVER THE AM TUNING INTERVAL]
The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the @/1 button to turn the power on.
2. Press the [TUNER/BAND] button to select TUNER (AM)
function.
3. Press the @/1 button again to turn the power off (standby).
4. While pressing the TUNING+ ML button, press the
@/1 button.
5. It turns power on and display "STEP 9kHz" or "STEP 10kHz",
and thus the tuning interval is changed over.
[MD/VIDEO FUNCTION CHANGE]
Select either VIDEO or MD of the external input.
Procedure:
1. Press the @/1 button to turn the power on.
2. Press the [FUNCTION] button to select MD or VIDEO function.
3. Press the @/1 button again to turn the power off (standby).
Q Q
4. While pressing the [FUNCTION] button, press the @/1 button.
3 6 7 1 3 1 5
5. The another function of the previous function is selected and
display "MD" or "VIDEO".
co
.
9 4 2 8
0 5 8 2 9 9 4 2 8
m
9 9
9 9