Table of Contents

Advertisement

QQ
3 7 63 1515 0
SERVICE MANUAL
Ver. 1.8 2006.01
HCD-HPX9 is the amplifier, CD player,
tape deck and tuner section in CMT-HPX9.
TE
L 13942296513
Main unit
Amplifier section
For the United States model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 6-ohm loads, both channels driven, from
120 – 10,000 Hz: rated 75 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
North American model:
Continuous RMS power output (reference):
Other models:
The following measured at AC 240 V, AC 220 V or AC
120 V
DIN power output (rated): 53 + 53 W
Continuous RMS power output (reference):
Inputs
MD/VIDEO:
Outputs
www
PHONES:
.
Sony Corporation
9-877-809-09
Personal Audio Division
2006A16-1
Published by Sony Techno Create Corporation
© 2006.01
http://www.xiaoyu163.com
SPEAKER:
CD player section
Laser
Frequency response
Tape deck section
Recording system
Frequency response
Tuner section
80 + 80 W
FM stereo, FM/AM superheterodyne tuner
(6 ohms at 1 kHz, 10%
FM tuner section
THD)
Tuning range
Antenna
Antenna terminals
I ntermediate frequency 10.7 MHz
AM tuner section
(6 ohms at 1 kHz, DIN)
Tuning range
Pan-American model:
70 + 70 W
(6 ohms at 1 kHz, 10%
THD)
Sensitivity 450/250 mV,
impedance 47 kilohms
Accepts headphones with
an impedance of 8 ohms or
x
ao
u163
y
more.
i
http://www.xiaoyu163.com
HCD-HPX9
2 9
8
Model Name Using Similar Mechanism
CD
CD Mechanism Type
Section
Base Unit Name
Optical Pick-up Block Name
Tape deck
Model Name Using Similar Mechanism
Q Q
Section
Tape Transport Mechanism Type
3
6 7
1 3
1 5
SPECIFICATIONS
Accepts impedance of 6 t
16 ohms.
Semiconductor laser
(λ=780 nm)
Emission duration:
continuous
20 Hz – 20 kHz
4-track 2-channel, stereo
50 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassettes
87.5 – 108.0 MHz
FM lead antenna
75 ohms unbalanced
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,710 kHz
(with the tuning interval
set at 9 kHz)
COMPACT DISC DECK RECEIVER
co
.
9 4
2 8
US Model
Canadian Model
E Model
Australian Model
NEW
CDM82A-F1BD81
BU-F1BD81A
KSM-215DCP
NEW
CMAL5Z225A
0 5
8
2 9
9 4
2 8
o
Other models:
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
Antenna
AM loop antenna, external
antenna terminal
Intermediate frequency 450 kHz
General
Power requirements
North American model: 120 V AC, 60 Hz
Australian model:
230 – 240 V AC, 50/60 Hz
Argentine model:
220 V AC, 50/60 Hz
Korea model:
220 V AC, 60 Hz
Saudi Arabian model:
120 – 127/220 or 230 – 240
V AC, 50/60 Hz
Adjustable with voltage
selector
Other models:
120 V, 220 V or 230 – 240
V AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption
North American model: 120 W
Other models:
105 W
Design and specifications are subject to change
without notice.
m
9 9
9 9

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-HPX9

  • Page 1 3 7 63 1515 0 SERVICE MANUAL US Model Canadian Model Ver. 1.8 2006.01 E Model Australian Model HCD-HPX9 is the amplifier, CD player, tape deck and tuner section in CMT-HPX9. Model Name Using Similar Mechanism CD Mechanism Type CDM82A-F1BD81 Section Base Unit Name...
  • Page 2: Table Of Contents

    HCD-HPX9 3 7 63 1515 0 TABLE OF CONTENTS SERVICING NOTES 4-3. Assembling of the Gear (Stock Rot Short) (Right) ..42 ..........4 4-4. Assembling of the Gear (Stock Rot Long) (Left) .... 43 4-5. Confirming the Assembling of the Stocker Section ..44 GENERAL ..............
  • Page 3: Leakage Test

    FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS • Usable with ordinary solder QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS It is best to use only unleaded solder but unleaded solder may PUBLIÉS PAR SONY.
  • Page 4: Servicing Notes

    HCD-HPX9 SECTION 1 SERVICING NOTES 3 7 63 1515 0 • MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP – Rear View – BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc.
  • Page 5: General

    HCD-HPX9 SECTION 2 This section is extracted GENRAL from instruction manual. 3 7 63 1515 0 • LOCATION OF CONTROLS Main unit ALPHABETICAL ORDER BUTTON DESCRIPTIONS ?/1 (power) 1 (8, 15, 20, 21, A – O P – Z ALBUM +/–...
  • Page 6: Setting The Clock

    HCD-HPX9 3 7 63 1515 0 Setting the clock Remote control ALPHABETICAL ORDER BUTTON DESCRIPTIONS Use buttons on the remote for the operation. ?/1 (power) 1 (8, 15, 20, 21, A – O P – Z Press ?/1 to turn on the system.
  • Page 7: Disassembly

    HCD-HPX9 SECTION 3 3 7 63 1515 0 DISASSEMBLY • This is can be disassemble according to the following sequence. 3-1. DISASSEMBLY FLOW-1 3-4.SIDE PLATE (L) (R), 3-3.OPTICAL PICK-UP TOP PANEL SECTION BLOCK (Page 10) (Page 9) 3-5.MECHANICAL DECK 3-6.FRONT PANEL SECTION...
  • Page 8: Disassembly Flow-2

    HCD-HPX9 3 7 63 1515 0 3-2. DISASSEMBLY FLOW-2 from DISASSEMBLY FLOW-1 3-14. PLATE (COVER TOP) (Page 17) 3-15. TOP SECTION (Page 17) 3-27. RUBBER ROLLER 3-26. SPR-E (ROLLER SLIDER UPPER) 3-16. ARM SECTION (TOP SECTION) (Page 26) (TOP SECTION) (Page 26) (Page 18) 3-18.
  • Page 9: Optical Pick-Up Block

    HCD-HPX9 3 7 63 1515 0 Note: Follow the disassembly procedure in the numerical order given. 3-3. OPTICAL PICK-UP BLOCK 2 bottom cover plate 1 two screws (BVTT3 × 6 ) 0 flotaing screw 4 screw (+PTPWH M2.6) (BTTP M2.6)
  • Page 10: Side Plate (L) (R), Top Panel Section

    HCD-HPX9 3 7 63 1515 0 3-4. SIDE PLATE (L) (R), TOP PANEL SECTION qs top panel section 7 side plate (L) 5 two screws 8 two screws (BVTP3 × 10 ) (BVTP3 × 8 ) 9 w ire (flat type)
  • Page 11: Mechanical Deck

    HCD-HPX9 3 7 63 1515 0 3-5. MECHANICAL DECK 6 two screws (BVTP2.6 × 8 ) 5 two screws (BVTP2.6 × 8 ) earth wire 7 cassette shield plate 8 mechanical deck qa cassette panel 0 leaf spring (cassette) 1 three screws (BVTP2.6 ×...
  • Page 12: Front Panel Section

    HCD-HPX9 3 7 63 1515 0 3-6. FRONT PANEL SECTION 6 w ire (flat type) 17p(CN310) 5 screw (BVTP3 × 6 ) 8 front panel section 2 screw (KTP3 × 8 ) 7 connector (CN604) 1 screw (KTP3 × 8 )
  • Page 13: Tuner (Fm/Am), Dc Fan

    HCD-HPX9 3 7 63 1515 0 3-8. TUNER (FM/AM), DC FAN MAIN board 2 screw (BVTP3 × 8 ) 9 w ire (flat type) 11p(CN305) 8 connector (CN313) 7 heat sink cover 1 two screws (BVTP3 × 8 )
  • Page 14: Main Board

    HCD-HPX9 3 7 63 1515 0 3-9. MAIN BOARD 6 connector (CN308) 5 connector (CN303) 3 connector (CN316) 2 connector (CN307) 4 connector (CN309) 9 MAIN board 1 w ire (flat type) 8 w ire (flat type) (9p)(CN306) 7 w ire (flat type)
  • Page 15: Amp Board, Switching Regulator

    HCD-HPX9 3 7 63 1515 0 3-11. AMP BOARD, SWITCHING REGULATOR 7 screw rear panel (BVTP3 × 8 ) 9 AMP board 5 two screws (BVTP3 × 12 ) 8 two screws (BVTP3 × 16 ) 6 main heat sink...
  • Page 16: Cd Mechanism Deck (Cdm82A)

    HCD-HPX9 3 7 63 1515 0 3-13. CD MECHANISM DECK (CDM82A) 3 sub chassis Please attach connector, 1 two screws (BVTT3 × 6 ) as shown in a figure. 2 two screws sub chassis (BVTT3 × 6 ) plate 6 screw (BVTP2.6 ×...
  • Page 17: Plate (Cover Top)

    HCD-HPX9 3 7 63 1515 0 3-14. PLATE (COVER TOP) 3 four screws (BTTPM 2.6 × 8) 4 plate (cover top) 2 gear (joint op), shaft (stock) 8 plate (cam R) 7 screw (BTTPM 2.6 × 8) 1 gear (joint op)
  • Page 18: Arm Section

    HCD-HPX9 3 7 63 1515 0 3-16. ARM SECTION 3 claw 2 Slide the arm section in the direction of the arrow B . 5 Remove the arm section in the direction of the arrow D . 4 Push this portion with a finger in the direction of the arrow C .
  • Page 19: Cd Mechanism Deck Section

    HCD-HPX9 3 7 63 1515 0 3-17. CD MECHANISM DECK SECTION 2 Slide the CD mechanism deck section in the direction of the arrow B . pulley (ELV motor) 1 T urn over the pulley (ELV motor) in the direction of the arrow A .
  • Page 20: Sub Gear (2 Step), Sub Slider Assy

    HCD-HPX9 3 7 63 1515 0 3-18. SUB GEAR (2 STEP), SUB SLIDER ASSY 9 Remove the sub slider assy in the direction of the arrow. 0 sub slider assy sub slider assy L 13942296513 4 sub gear (idler) 3 cover (R) 2 two screws (M2 ×...
  • Page 21: Arm (R)

    HCD-HPX9 3 7 63 1515 0 3-19. ARM (R) 1 sub gear (joint just front) 2 SPR-T (sub gear back R) 3 lever (sub gear back R) L 13942296513 5 gear (sub gear pin right) 4 two washers (5.5)
  • Page 22: Gear (Stock Planet) (Right)

    HCD-HPX9 3 7 63 1515 0 3-20. GEAR (STOCK PLANET) (RIGHT) 1 two screws (BTTP M2.6 × 6) 2 stock base (A) 3 gear (stock sun) 4 gear (stock planet) L 13942296513 3-21. LEVER (SUB GEAR BACK L) 2 screw (M2 × 5) 1 screw (K2.6 ×...
  • Page 23: Arm (L)

    HCD-HPX9 3 7 63 1515 0 3-22. ARM (L) 1 two washers (5.5) 2 gear (sub gear pin right) 3 gear (stock rotary right) 4 arm (L), stock base (B) UPPER SIDE L 13942296513 6 gear (stock sun) 5 gear (stock planet)
  • Page 24: Gear (Stock Rot Long) (Left)

    HCD-HPX9 3 7 63 1515 0 3-23. GEAR (STOCK ROT LONG) (LEFT) 1 two screws (2 × 6) 2 stock box (L) 3 gear (stock rot short) short 4 gear (stock rot long) long UPPER SIDE L 13942296513 3-24. GEAR (STOCK ROT SHORT) (RIGHT) 1 two screws (2 ×...
  • Page 25: Stocker (1) Assy To Stocker (5) Assy

    HCD-HPX9 3 7 63 1515 0 3-25. STOCKER (1) ASSY TO STOCKER (5) ASSY UPPER SIDE 2 claw 1 dowel Repeat the steps 1 to 1 , when removing the part 3 Remove the stocker (1) assy in the direction of the arrow.
  • Page 26: Spr-E (Roller Slider Upper) (Top Section)

    HCD-HPX9 3 7 63 1515 0 3-26. SPR-E (ROLLER SLIDER UPPER) (TOP SECTION) 3 SPR-E (8 cm slider L) 5 bushing 1 bushing UPPER SIDE 2 SPR-T (8 cm slider R) top section 4 SPR-E (roller slider upper) L 13942296513 3-27.
  • Page 27: Lod Motor

    HCD-HPX9 3 7 63 1515 0 3-28. LOD MOTOR 6 Remove soldering from the two points 5 two screws 3 three screws (BTTP M2.6 × 8) 2 sub chassis assy (L) (BTTP M2.6 × 8) 4 belt (MOT-OP) 7 LOD MOTOR board...
  • Page 28: Rotary Encoder

    HCD-HPX9 3 7 63 1515 0 3-30. ROTARY ENCODER 4 Rotate the ELV motor until the position for 1 three screws (BTTP M2.6 × 6) the hole on the chassis can be seen through the plate (comR). 2 RELAY board...
  • Page 29: Assembling Of The Rotary Encoder

    HCD-HPX9 3 7 63 1515 0 3-31. ASSEMBLING OF THE ROTARY ENCODER 4 screw (PTPWH2.6 × 8) 1 rotary encoder 2 two claws 3 Apply the soldering in five points. 8 screw (PTPWH2.6 × 8) 9 screw gear (encoder) (PTPWH2.6 ×...
  • Page 30: Elv Motor

    HCD-HPX9 3 7 63 1515 0 3-32. ELV MOTOR 2 two screws (BTTP M2.6 × 8) 3 Remove soldering 4 ELV MOTOR board from the five points 5 ELV motor L 13942296513 1 belt (MOT-UD) belt (MOT-UD) UPPER SIDE u163 http://www.xiaoyu163.com...
  • Page 31: Chassis (Top), Chassis (Bottom)

    HCD-HPX9 3 7 63 1515 0 3-33. CHASSIS (TOP), CHASSIS (BOTTOM) 1 screw (BVTP2.6 × 8) 4 three screws (BVTP2.6 × 8) 2 lever (CL UP2) 3 two screws (P2 × 10) 5 chassis (top) L 13942296513 7 chassis (bottom)
  • Page 32: Lever (Loading R, Loading L)

    HCD-HPX9 3 7 63 1515 0 3-34. LEVER (LOADING R, LOADING L) SPR-T (loading L) SPR-T (loading R) L 13942296513 6 lever (loading R) 3 two hooks 5 two hooks 4 lever (loading L) PRECAUTION DURING LEVER (LOADING R/L) INSTALLATION Align the horizontal position.
  • Page 33: Disc Stop Lever

    HCD-HPX9 3 7 63 1515 0 3-35. DISC STOP LEVER 1 gear (cap) 2 gear (IDL L) PRECAUTION DURING DISC STOP LEVER INSTALLATION chassis (top) hole 5 two hooks 3 two claws disc stop lever 6 disc stop lever...
  • Page 34: Cd Board (A)

    HCD-HPX9 3 7 63 1515 0 3-37. CD BOARD (A) 1 screw (BVTP2.6 × 8) 2 Remove soldering 4 CD (A) board from the four points. 3 wire (flat type) (16 core) (CN102) L 13942296513 3-38. OPTICAL PICK-UP (KSM-215DCP)
  • Page 35: Base Unit Section

    HCD-HPX9 3 7 63 1515 0 3-39. BASE UNIT SECTION 6 Remove the base unit 4 floating screw in the direction of the arrow. (PTPWH M2.6) 3 SPR-E 213 down holder 5 floating screw (PTPWH M2.6) 2 lever (CL UP2)
  • Page 36: Gear (Idl-B)

    HCD-HPX9 3 7 63 1515 0 3-41. GEAR (IDL-B) 2 claw 3 gear pulley 4 gear (cap) 5 gear (IDL-A) 8 stopper 9 DIR lever q; gear (IDL B long) 1 DIR spring 6 Loosen the screw. L 13942296513 7 Hold the Release lever and change the direction.
  • Page 37: Spr-E (Tako-Back)

    HCD-HPX9 3 7 63 1515 0 3-43. SPR-E (TAKO-BACK) two claws two claws parasol rubber roller 1 four screws (2 × 5) 2 four parasols 5 SPR-E (tako-back) L 13942296513 4 tension spring (lower) 3 four rubber rollers u163...
  • Page 38: Plate (Push) Assy

    HCD-HPX9 3 7 63 1515 0 3-44. PLATE (PUSH) ASSY 1 SPR-E (plate-push-back) 5 Remove the plate (push) assy in the direction of the arrow. 2 screw (PTPWH M2) 3 gear (tako second) 4 four claws PRECAUTION DURING GEAR (TAKO SECOND) INSTALLATION Adjust phases.
  • Page 39: Spr-P (Lock)

    HCD-HPX9 3 7 63 1515 0 3-45. SPR-P (LOCK) 2 lever (lock) 1 claw 3 SPR-P (lock) PRECAUTION DURING LEVER INSTALLATION L 13942296513 3 lever (lock) 2 Hold the both ends of the SPSR-P (lock) with two claws. 1 SPR-P (lock) 4 Pick up the SPR-P (lock) from the claw and hook it on the lever.
  • Page 40: Assembly

    HCD-HPX9 SECTION 4 3 7 63 1515 0 ASSEMBLY • This is can be assemble according to the following sequence. 4-1. ASSEMBLY FLOW 4-2. ASSEMBLING OF THE STOCKER SECTION (Page 41) 4-3. ASSEMBLING OF THE GEAR (STOCK ROT SHORT) (RIGHT) (Page 42) 4-4.
  • Page 41: Assembling Of The Stocker Section

    HCD-HPX9 3 7 63 1515 0 4-2. ASSEMBLING OF THE STOCKER SECTION Check the number on each stocker assy, before assembling all the assys. 2 stocker (1) assy UPPER SIDE 3 stocker (2) assy L 13942296513 5 tow claws...
  • Page 42: Assembling Of The Gear (Stock Rot Short) (Right)

    HCD-HPX9 3 7 63 1515 0 4-3. ASSEMBLING OF THE GEAR (STOCK ROT SHORT) (RIGHT) 7 two screws (2 × 6) Note: Install the stock box (R) right after 8 screw (1.7) finishing the phase adjustment. 6 stock box (R)
  • Page 43: Assembling Of The Gear (Stock Rot Long) (Left)

    HCD-HPX9 3 7 63 1515 0 4-4. ASSEMBLING OF THE GEAR (STOCK ROT LONG) (LEFT) 6 two screws (2 × 6) Note. Install the stock box (L) right after finishing the phase adjustment. 7 stocker box (L) 2 gear (stock rot short)
  • Page 44: Confirming The Assembling Of The Stocker Section

    HCD-HPX9 3 7 63 1515 0 4-5. CONFIRMING THE ASSEMBLING OF THE STOCKER SECTION UPPER SIDE stocker section STOCKER ASSY (R) SIDE FRONT SIDE L 13942296513 3 Confirm that each claw contacts uniformly at the respective stop positions of the stocker assy (1) to the stocker assy (5).
  • Page 45: Assembling Of The Gear (Stock Rotary Left)

    HCD-HPX9 3 7 63 1515 0 4-6. ASSEMBLING OF THE GEAR (STOCK ROTARY LEFT) PRECAUTION DURING GEAR (STOCK PLANET) INSTALLATION 2 gear (stock sun) 3 Position to adjust phases 4 gear (stock planet) 1 Align the edges of stockers, for the gear (stock sun).
  • Page 46: Assembling Of The Gear (Stock Rotary Right)

    HCD-HPX9 3 7 63 1515 0 4-7. ASSEMBLING OF THE GEAR (STOCK ROTARY RIGHT) qa washers (5.5) 0 gear (stock rotary right) The cut-off curve should face to the front. UPPER SIDE 1 Turn over the stocker assy in the direction of the arrow.
  • Page 47: Assembling Of The Lever (Sub Gear Back L)

    HCD-HPX9 3 7 63 1515 0 4-8. ASSEMBLING OF THE LEVER (SUB GEAR BACK L) PRECAUTION DURING SPR-T (SUB GEAR BACK L) INSTALLATION gear (stock rotary left) lever (sub gear back L) 1 Turn over the stocker assy gear (sub gear pin left) in the direction of the arrow.
  • Page 48: Assembling Of The Gear (Sub Gear Pin Right)

    HCD-HPX9 3 7 63 1515 0 4-9. ASSEMBLING OF THE GEAR (SUB GEAR PIN RIGHT) 1 Turn over the stocker assy in the direction of the arrow. PRECAUTION DURING GEAR (SUB GEAR PIN RIGHT) INSTALLATION gear (sub gear pin right) UPPER 6 Adjust phases.
  • Page 49: Assembling Of The Lever (Sub Gear Back R)

    HCD-HPX9 3 7 63 1515 0 4-10. ASSEMBLING OF THE LEVER (SUB GEAR BACK R) 1 sub (joint just front) 2 gear (stock joint) Note: Put the driver on the bottom of the other side of the gear, and push the gear (stock joint) into it. Confirm it is attached securely.
  • Page 50: Assembling Of The Sub Gear (Idler)

    HCD-HPX9 3 7 63 1515 0 4-11. ASSEMBLING OF THE SUB GEAR (IDLER) 4 Position to adjust phases for the sub gear (idler). 1 Push the sub slider assy in the direction of the arrow A until it stops.
  • Page 51: Assembling Of The Sub Gear (2 Step)

    HCD-HPX9 3 7 63 1515 0 4-12. ASSEMBLING OF THE SUB GEAR (2 STEP) PRECAUTION DURING SUB GEAR (2 STEP) INSTALLATION 1 sub gear (2 step) 2 Align the sub gear (2 step) and the gear (sub gear pin right) hole.
  • Page 52: Confirming The Assembling Of The Arm Section

    HCD-HPX9 3 7 63 1515 0 4-13. CONFIRMING THE ASSEMBLING OF THE ARM SECTION Note. 2 Check point 1: If the two parts of the stopper do not touch the stock base (B) when The smooth movement of the sub slider assy is pushed to the end, the phases are not correctly this part when sliding.
  • Page 53: Test Mode

    HCD-HPX9 Ver. 1.6 SECTION 5 3 7 63 1515 0 TEST MODE [MC COLD RESET] [PANEL TEST MODE] The cold reset clears all data including preset data stored in the Enter The Panel Test Mode memory to initial conditions. Execute this mode when returning Procedure: the set to the customer.
  • Page 54 HCD-HPX9 Ver. 1.6 3 7 63 1515 0 [CD SHIP MODE] [CD POWER MANAGE] This mode can run the CD sled motor optionally. Use this mode, for This mode is for switch the CD power supply on/off. Even if this instance, when cleaning the optical pick-up.
  • Page 55: Electrical Adjustments

    HCD-HPX9 SECTION 6 3 7 63 1515 0 ELECTICAL ADJUSTMENTS Procedure: DECK SECTION Connect a digital voltmeter (AC range) to TP101 (L), TP201 (R) and TP (GND) on the MAIN board. 1. Demagnetize the record/playback head with a head Insert a blank tape (CS-123).
  • Page 56 HCD-HPX9 3 7 63 1515 0 CD SECTION RF signal waveform VOLT/DIV : 200mV Note: TIME/DIV : 500ns 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 (3-702-101-01) unless otherwise indicated.
  • Page 57: Diagrams

    HCD-HPX9 SECTION 7 3 7 63 1515 0 DIAGRAMS • Circuit Boards Location AMP board POWER board PANEL (1) board HEADPHONE board MAIN board L 13942296513 PANEL (2) board DRIVER board SW board (D) SW board (C) SW board (A)
  • Page 58 HCD-HPX9 3 7 63 1515 0 NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Boards: Note on Schematic Diagram: • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. (p: pF) •...
  • Page 59: Block Diagrams - Cd Servo Section

    HCD-HPX9 7-1. BLOCK DIAGRAMS — CD SERVO SECTION — 3 7 6 3 1 5 1 5 0 FILTER CD DSP XTAO IC101 (1/2) CLOCK X171 45 46 51 53 50 52 DETECTOR XTAI CD +3V GENERATOR 16.9344MHz XTACN...
  • Page 60: Block Diagrams - Main Section

    HCD-HPX9 7-2. BLOCK DIAGRAMS — MAIN SECTION — 3 7 6 3 1 5 1 5 0 AC DET HP SW J301 INPUT SELECT, R-CH J321 MD IN L TONE CONTROL, POWER ON ELECTRICAL VOLUME PHONES MUTING IC302 MD/VIDEO...
  • Page 61: Block Diagrams - Panel/Power Supply Section

    HCD-HPX9 7-3. BLOCK DIAGRAMS — PANEL/POWER SUPPLY SECTION — 3 7 6 3 1 5 1 5 0 SYSTEM CONTROLLER FL/LED DRIVER IC306 (3/3) IC801 REMOTE CONTROL GR1 – GR12 RECEIVER SIRCS IN/ FL701 IC802 WAKE FLUORESCENT INDICATOR TUBE SG1 –...
  • Page 62: Printed Wiring Board - Cd Board

    HCD-HPX9 • See page 57 for Circuit Boards Location. 7-4. PRINTED WIRING BOARD — CD BOARD — :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 CD BOARD (COMPONENT SIDE) M101 (SPINDLE) CD BOARD (CONDUCTOR SIDE)
  • Page 63: Schematic Diagram - Cd Board

    HCD-HPX9 • See page 58 for Waveforms. • See page 76, 77 for IC Block Diagrams. 7-5. SCHEMATIC DIAGRAM — CD BOARD — 3 7 6 3 1 5 1 5 0 C131 100p TP423 IOP1 C142 1500p C134...
  • Page 64: Printed Wiring Board - Cd Mechanism Section

    HCD-HPX9 • See page 57 for Circuit Boards Location. 7-6. PRINTED WIRING BOARD — CD MECHANISM SECTION — :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 DRIVER BOARD S702 (CHUCK) S701 (LOD POSITION/CLOSE) (OUT) M701...
  • Page 65: Schematic Diagram - Cd Mechanism Section

    HCD-HPX9 • See page 78 for IC Block Diagram. 7-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — 3 7 6 3 1 5 1 5 0 IC701 R851 R853 R855 R857 R859 R861 BA6956AN 4.7k 4.7k 4.7k 4.7k 4.7k 4.7k...
  • Page 66: Printed Wiring Board - Main Board

    HCD-HPX9 • See page 57 for Circuit Boards Location. 7-8. PRINTED WIRING BOARD — MAIN BOARD — :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 TAPE MECHANISM HRP350 DECK BLOCK FM/AM TUNER UNIT M301 • Semiconductor...
  • Page 67: Q Q 7-9. Schematic Diagram - Main Board (1/3)

    HCD-HPX9 • See page 58 for Waveforms. • See page 78 for IC Block Diagram. 7-9. SCHEMATIC DIAGRAM — MAIN BOARD (1/3) — 3 7 6 3 1 5 1 5 0 CN306 C322 C321 C141 0.01 R118 C131 R391 4.7k...
  • Page 68: Schematic Diagram - Main Board (2/3)

    HCD-HPX9 • See page 58 for Waveforms. • See page 80 for IC Pin Function Description. 7-10. SCHEMATIC DIAGRAM — MAIN BOARD (2/3) — 3 7 6 3 1 5 1 5 0 CN315 R311 R312 R377 Q308 R358...
  • Page 69: Schematic Diagram - Main Board (3/3)

    HCD-HPX9 7-11. SCHEMATIC DIAGRAM — MAIN BOARD (3/3) — 3 7 6 3 1 5 1 5 0 TM301 CN309 L102 L202 CN313 C133 C233 M301 RY301 C134 C234 R122 R222 R120 R220 1/2W 1/2W CN316 C135 0.01 C235 0.01...
  • Page 70: Printed Wiring Board - Amp Board

    HCD-HPX9 • See page 57 for Circuit Boards Location. 7-12. PRINTED WIRING BOARD — AMP BOARD — :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 AMP BOARD D610 D607 R616 Q607 R617 R618 C609 C617...
  • Page 71: Schematic Diagram - Amp Board

    HCD-HPX9 • See page 79 for IC Block Diagram. 7-13. SCHEMATIC DIAGRAM — AMP BOARD — 3 7 6 3 1 5 1 5 0 C609 D610 1SS133T-77 IC601 STK403-090-S R616 R618 R619 D608 1SS133T-77 R626 IC602 RT8H015C-T112-1 Q608...
  • Page 72: Printed Wiring Board - Panel Section

    HCD-HPX9 • See page 57 for Circuit Boards Location. 7-14. PRINTED WIRING BOARD — PANEL SECTION — :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 BOARD CN604 (FLUORESCENT INDICATOR TUBE) (Page 70) IC802 IC801 REPEAT/...
  • Page 73: Schematic Diagram - Panel Section

    HCD-HPX9 • See page 79 for IC Block Diagram. 7-15. SCHEMATIC DIAGRAM — PANEL SECTION — 3 7 6 3 1 5 1 5 0 FL701 S803 IC802 NJL73H400A C838 220p C820 220p CN311 C821 220p R845 C804 R841 0.01...
  • Page 74: Printed Wiring Board - Power Board

    HCD-HPX9 • See page 57 for Circuit Boards Location. 7-16. PRINTED WIRING BOARD — POWER BOARD — :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 (US,CND) SUB PANEL BLOCK (EXCEPT US,CND) 1 3 9 4 2 2 9 6 5 1 3...
  • Page 75: Schematic Diagram - Power Board

    HCD-HPX9 Ver 1.1 7-17. SCHEMATIC DIAGRAM — POWER BOARD — 3 7 6 3 1 5 1 5 0 D914 1N4002B IC901 D904 D908 D906 TA7810S D902 1N4002B 1N4002B 1N4002B 1N4002B C909 D903 D905 C907 C901 1N4002B 1N4002B D907...
  • Page 76 HCD-HPX9 3 7 6 3 1 5 1 5 0 • IC Block Diagrams – CD BOARD – IC101 CXD3059AR IC251 BA5947FM 115 114 112 111 110 109 103 102 101 100 119 118 CPU INTERFACE MUTING SERVO INTERFACE 90 RMUT + –...
  • Page 77 HCD-HPX9 3 7 63 1515 0 IC301 TC94A34FG-002 Timing Generator VDDP PO5/AD5 /RESET PO6/AD6 STANDBY PO7AD7 /MICS /MILP MIDIO AD10 VDDT /MICK L 13942296513 /MIACK/ SRMSTB AD16 VDDT VDDM PO8/AD11 SDO0 PO9/AD12 /CCE/ PO10/ BCKO AD13 BUCK/ PO11/ LRCKO...
  • Page 78 HCD-HPX9 3 7 63 1515 0 – CONNECTOR BOARD – – DRIVER BOARD – IC801, 811 BA6956AN IC701 BA6956AN CONTROL LOGIC – MAIN BOARD – IC302 BD3402KS2 56 55 54 53 52 51 48 NC 47 NC 46 NC...
  • Page 79 HCD-HPX9 3 7 63 1515 0 – AMP BOARD – IC602 RT8H015C-T112-1 OVER LOAD DETECT DETECT – PANEL (1) BOARD – IC801 uPD16315GB-3BS Grid driver Multiplexed driver SEG19/GRID10 L 13942296513 Command decoder LED1 SEG18/GRID11 LED2 Display memory LED3 SEG17/GRID12...
  • Page 80 HCD-HPX9 3 7 63 1515 0 • IC Pin Function Description MAIN BOARD IC306 M3062CMEN-A02FPU0 (SYSTEM CONTROLLER) Pin No. Pin Name Description CD DISCSENS 2 DISC 4, 5 and DISC (+1) detect signal input CD DISCSENS 1 DISC 1 to 3 detect signal input...
  • Page 81 HCD-HPX9 3 7 63 1515 0 Pin No. Pin Name Description SW2-2 CD loading position switch input terminal (LOD POSITION) SW1 (OPEN) CD open switch input terminal ELV NEG Elevator up/down motor control signal output ELV POS Elevator up/down motor control signal output...
  • Page 82 HCD-HPX9 3 7 63 1515 0 Pin No. Pin Name Description MODEL Setting terminal for the model type DEST Setting terminal for the destination TC END SW End switch detection from tape deck block TC HALF/REC SW Half/REC switch detection from tape deck block AVSS —...
  • Page 83: Exploded Views

    HCD-HPX9 Ver. 1.5 SECTION 8 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 or may have some difference from the original number in the exploded views are not supplied.
  • Page 84: Front Panel Section

    4-247-752-01 RUBBER, FOOT A-1076-938-A PANEL (1) BOARD, COMPLETE (KR) 3-921-725-01 SCREW +PWH 2.6X10 (including PANEL (2), HEADPHONE and POWER board) 3-038-018-01 EMBLEM, SONY A-4751-221-A PANEL (1) BOARD, COMPLETE (US, CND) (including PANEL (2), HEADPHONE and POWER board) 4-951-620-01 SCREW (2.6X8), +BVTP...
  • Page 85: Chassis Section

    HCD-HPX9 Ver. 1.7 3 7 63 1515 0 8-3. CHASSIS SECTION v C : POWER board supplied supplied F902 supplied F901 T901 supplied F903 supplied CD mechanism deck section (CDM82A) supplied supplied supplied L 13942296513 supplied supplied Ref. No.
  • Page 86: Cd Mechanism Deck Section-1 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-4. CD MECHANISM DECK SECTION-1 (CDM82A) CD mechanism deck section -8, -9, -10 (CDM82A), base unit section (BU-F1BD81A) supplied CD mechanism deck section -5 (CDM82A) CD mechanism deck section -6, -7...
  • Page 87: Cd Mechanism Deck Section-2 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-5. CD MECHANISM DECK SECTION-2 (CDM82A) CD mechanism deck section -3, -4 (CDM82A) L 13942296513 767 768 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-641-430-31 SCREW (2.6), (+) K TAPPING 4-253-564-01 SCREW (1.7)
  • Page 88: Cd Mechanism Deck Section-3 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-6. CD MECHANISM DECK SECTION-3 (CDM82A) L 13942296513 UPPER SIDE CD mechanism deck section -4 (CDM82A) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-252-802-01 GEAR (STOCK SUN) 4-218-252-02 SCREW (+PTPWH M2.6), FLOATING...
  • Page 89: Cd Mechanism Deck Section-4 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-7. CD MECHANISM DECK SECTION-4 (CDM82A) L 13942296513 UPPER SIDE Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1060-624-A STOCKER (5) ASSY 4-253-344-01 SCREW (2) A-1060-625-A STOCKER (4) ASSY...
  • Page 90: Cd Mechanism Deck Section-5 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-8. CD MECHANISM DECK SECTION-5 (CDM82A) supplied supplied supplied supplied supplied L 13942296513 supplied supplied supplied supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-253-344-01 SCREW (2)
  • Page 91: Cd Mechanism Deck Section-6 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-9. CD MECHANISM DECK SECTION-6 (CDM82A) supplied supplied supplied not supplied M881 M871 supplied not supplied L 13942296513 CD mechanism deck section -7 (CDM82A) Ref. No. Part No. Description Remark Ref. No.
  • Page 92: Cd Mechanism Deck Section-7 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-10. CD MECHANISM DECK SECTION-7 (CDM82A) 1006 1005 1004 1002 1008 1009 supplied 1003 1007 1001 S881 L 13942296513 1010  Ref. No. Part No. Description Remark Ref. No. Part No. Description...
  • Page 93: Cd Mechanism Deck Section-8 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-11. CD MECHANISM DECK SECTION-8 (CDM82A) 1079 1060 1078 1077 1076 1075 1062 1060 1080 1060 1061 1074 M701 1060 1051 1059 1081 1058 1073 1056 1082 1055 1072 1063 1070...
  • Page 94: Cd Mechanism Deck Section-9 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-12. CD MECHANISM DECK SECTION-9 (CDM82A) 1122 1123 1121 1130 1125 1131 1120 1126 1109 1132 1124 1127 1133 1101 1102 1106 1119 1134 1135 1103 1126 1104 1105 1129 1106...
  • Page 95: Cd Mechanism Deck Section-10 (Cdm82A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-13. CD MECHANISM DECK SECTION-10 (CDM82A) 1160 1159 1158 1157 1156 1155 1152 1159 1154 1153 1161 L 13942296513 1163 1151 1162 Ref. No. Part No. Description Remark Ref. No. Part No.
  • Page 96: Base Unit Section (Bu-F1Bd81A)

    HCD-HPX9 Ver. 1.8 3 7 63 1515 0 8-14. BASE UNIT SECTION (BU-F1BD81A) 1209 1205 1208 1204 1207 1206 1205 1205 1204 1204 1207 L 13942296513 1203 1205 1210 1204 1203 1210 S101 1201 1202 Ref. No. Part No.
  • Page 97: Electrical Parts List

    HCD-HPX9 SECTION 9 Ver 1.1 ELECTRICAL PARTS LIST 3 7 63 1515 0 NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they When indicating parts by reference number, parts list may be different from the parts are seldom required for routine service.
  • Page 98 HCD-HPX9 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R555 1-216-864-11 SHORT CHIP C116 1-128-995-21 ELECT CHIP 100uF R556 1-216-822-11 METAL CHIP 1.2K 1/10W C122 1-107-826-11 CERAMIC CHIP 0.1uF R557...
  • Page 99 HCD-HPX9 3 7 63 1515 0 CONNECTOR Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C316 1-162-966-11 CERAMIC CHIP 0.0022uF 10% R303 1-216-845-11 METAL CHIP 100K 1/10W C317 1-162-970-11 CERAMIC CHIP 0.01uF R305 1-216-845-11 METAL CHIP...
  • Page 100 HCD-HPX9 CONNECTOR DISC ADDRESS SW Ver. 1.3 ELV MOTOR DRIVER 3 7 63 1515 0 HEADPHONE MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R852 1-249-429-11 CARBON 1/4W HEADPHONE BOARD R853 1-249-425-11 CARBON 4.7K...
  • Page 101 HCD-HPX9 3 7 63 1515 0 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C137 1-126-965-91 ELECT 22uF C331 1-126-925-91 ELECT 470uF C138 1-162-960-11 CERAMIC CHIP 220PF C333 1-126-964-11 ELECT 10uF C141 1-126-964-11 ELECT...
  • Page 102 HCD-HPX9 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > < COIL > D301 8-719-991-33 DIODE 1SS133T-77 L102 1-422-009-13 COIL, AIR-CORE D302 8-719-991-33 DIODE 1SS133T-77 L202 1-422-009-13 COIL, AIR-CORE...
  • Page 103 HCD-HPX9 3 7 63 1515 0 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R201 1-216-821-11 METAL CHIP 1/10W R341 1-216-841-11 METAL CHIP 1/10W R202 1-216-841-11 METAL CHIP 1/10W R342 1-216-841-11 METAL CHIP 1/10W...
  • Page 104 HCD-HPX9 Ver. 1.3 MAIN MOTOR LOD 3 7 63 1515 0 PANEL (1) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R417 1-216-833-11 METAL CHIP 1/10W < RELAY > R418 1-247-807-31 CARBON 1/4W R419 1-247-807-31 CARBON...
  • Page 105 HCD-HPX9 Ver. 1.3 3 7 63 1515 0 PANEL (1) PANEL (2) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C836 1-162-971-11 CERAMIC CHIP 0.001uF R818 1-216-829-11 METAL CHIP 4.7K 1/10W C837 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 106 HCD-HPX9 Ver. 1.3 PANEL (2) POWER SW (A) SW (B) SW (C) 3 7 63 1515 0 SW (D) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > < FUSE HOLDER > R821...
  • Page 107 HCD-HPX9 Ver. 1.8 3 7 63 1515 0 Ref. No. Part No. Description Remark MISCELLANEOUS ************** 1-796-352-51 DECK, MECHANICAL (CMAL5Z225A) 1-773-052-11 WIRE (FLAT TYPE)(17CORE) 1-693-625-11 TUNER (FM/AM) (US, CND) 1-693-628-11 TUNER (FM/AM) (E, EA, AR, AUS) 1-693-629-11 TUNER (FM/AM) (KR)
  • Page 108 HCD-HPX9 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.

This manual is also suitable for:

Hcd-hpx10w

Table of Contents