ENGLISH (Original instructions) SPECIFICATIONS Model DUR364L Type of handle Loop handle No load speed 5,000 / 6,500 min Overall length 1,754 mm Nylon cord diameter 2.0 – 2.4 mm Applicable cutting tool Nylon cutting head Plastic blade Nylon cutting head...
・ Only for EU countries Director Ni-MH Do not dispose of electric equipment or Li-ion Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium battery pack together with household waste material! GEB109-3 In observance of the European Directives, IMPORTANT SAFETY on Waste Electric and Electronic Equipment...
Page 4
12. Never operate the tool when tired, feeling ill or When battery pack is not in use, keep it away under the influence of alcohol or drugs. from other metal objects, like paper clips, 13. The tool should be switched off immediately if coins, keys, nails, screws or other small metal it shows any signs of unusual operation.
Page 5
Before starting make sure that the cutting tool 17. Don't force the tool. It will do the job better has no contact with hard objects such as and with less likelihood of a risk of injury at branches, stones etc. as the cutting tool will the rate for which it was designed.
Page 6
If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. Do not short the battery cartridge: Do not touch the terminals with any conductive material. Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
PARTS DESCRIPTION Battery cartridge Lock-off lever Switch trigger Power lamp Main power button Reverse button Hanger Grip Protector (cutting tool guard) 015385...
Overload protection FUNCTIONAL DESCRIPTION Blinking WARNING: Always be sure that the tool is switched off and • the battery cartridge is removed before adjusting or checking function on the tool. Failure to switch off and remove the battery cartridge may result in 015451 serious personal injury from accidental start-up.
Page 9
Remaining battery capacity indication To stop the tool, release the switch trigger. NOTE: Battery indicator status The tool is automatically turned off after the tool is • Remaining battery capacity Blinking left one minute without any operations. Speed adjusting 50% - 100% 1.
Always be sure that the tool is switched off and • NOTICE: battery cartridge is removed before carrying out Be sure to use genuine Makita nylon cutting head / • any work on the tool. Failure to switch off and plastic blade.
1. Plastic blade 2. Nut 3. Metal guard 4. Receive washer 5. Hex wrench 015393 015394 Insert the hex wrench through the hole on the motor housing MAINTENANCE and rotate the receive washer until it is locked with the hex wrench.
Page 12
RH. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. 013825 Wind all but about 100 mm of the cords, leaving the ends temporarily hooked through a notch on the side of the spool.
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs. Malfunction status...
Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Nylon cutting head • Nylon cord (cutting line) • Plastic blade •...
Need help?
Do you have a question about the DUR364L and is the answer not in the manual?
Questions and answers
Why is my makita grass trimmer power is on but not spin how can I fix it please
Your Makita DUR364L grass trimmer may be powered on but not spinning due to the following reasons:
1. A foreign object is stuck between the guard and the nylon cutting head.
Fix: Remove the object.
2. The drive system is malfunctioning.
Fix: Take the trimmer to an authorized service center for repair.
3. A nylon cutting line has broken.
Fix: Tap the nylon cutting head on the ground while it is spinning to feed more line.
If none of these solutions work, remove the battery and seek professional servicing.
This answer is automatically generated