Panasonic WV-CS954 Operating Instructions Manual page 28

** POSITION 1
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ←
RET TOP
FLOOR1
DOOR
3. Use the joystick to position the camera, and then
press the CAM (SET) button.
** POSITION 1
PAN/TILT
ZOOM/FOCUS
U TILT D/L PAN R
PAN OFFSET SET ←
RET TOP
FLOOR1
DOOR
4. Move the cursor to → PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET)
button to display the ZOOM/FOCUS setting menu.
** POSITION 1
PAN/TILT
ZOOM/FOCUS
U ZOOM D/L FOCUS R
PAN OFFSET SET ←
RET TOP
FLOOR1
DOOR
5. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.
Notes:
• Focusing may be difficult when the camera is at
an angle that is close to horizontal.
• A different position number can be selected by
moving the cursor to the position number at the
top of the position setting menu and tilting the
joystick left and right. Pressing the CAM (SET)
button will change to the setting screen for the
newly selected position number.
• The currently registered camera ID and preset ID
appear at the bottom of the position setting menu.
• When using a system device other than the WV-
CU650/CU950*,
position numbers cannot be set. (as of February 2005)
* Operation procedure may vary depending on
the version of the system controller's software.
For Ver.1.xx or earlier: only camera function
operations are supported
For Ver.2.xx or later: PRESET/PGM PRESET
button is also supported
Align the cursor here
** POSITION 1*
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ←
RET TOP
FLOOR1
DOOR
**
→PUSH SET
→ PUSH SET
→
0
**
→PUSH SET
→PUSH SET
→
0
**
→PUSH SET
→PUSH SET
→
0
WJ-HD309A/HD316A over
**
→ PUSH SET
→PUSH SET
→
0
● Adjusting Camera Position When
Changing Cameras (PAN OFFSET SET)
The system controller etc. has a function for
downloading (saving) and uploading (recovering)
setting information for the camera. This function allows
you to upload (recover) original setting information that
has been
unforeseen damage or malfunction causes setting
information in the camera to be lost. However, there
may be some slight differences in images from those
uploaded (recovered) when the camera is changed.
The "PAN OFFSET SET" function is for adjusting these
differences.
1. Align the cursor with "PAN OFFSET SET" with the ←
or → arrow, and press the CAM (SET) button to set
the offset value.
Set the offset value to 0.0, or in a range of -10 to
+10. All preset positions for the camera's position
are adjusted according to the offset value.
Important: Data is not compatible with existing
cameras.
existing cameras will damage data in the camera. If
data in the camera is damaged, download camera
setting information from a camera that still has the
factory settings and then upload it to the camera
with the damaged data.
● Preset ID Setting (PRESET ID)
The preset ID is a series of alphanumeric characters
that indicate the location of the camera. This item can
be used to turn display of the preset ID on the monitor
screen on or off, and to input the preset ID.
1. Move the cursor to PRESET ID, and then tilt the
joystick left or right to toggle preset ID display on
and off.
65
2. Select ON or OFF, and then press the CAM (SET)
button.
This will display the preset ID setting menu.
3. Use the joystick to move the cursor the character you
want to input, and then press the CAM (SET) button.
The text input procedure is the same as that for
camera ID input.
See steps 3 through 5 under "(1) Camera ID
(CAMERA ID)" on page 22 for information about
inputting the text for the preset ID and specifying its
position on the display.
-28-
downloaded (saved)
Uploading setting information
PRESET NO. 1*
POSITION SET
PRESET ID ON
ALC/MANUAL ALC
AF MODE MANUAL L
DWELL TIME 10S
SCENE FILE OFF
PRESET SPEED ••••••••I
L
RET TOP DEL
before some
from
H