Samsung HG75AD690U Installation Manual page 31

Hotel TV Function
No
Category
Sub Amp Mode
Bathroom
10
Speaker
Sub Amp Volume
HP Mode
HP
11 Default HP Volume
Management
Main Speaker
Eco
12 Energy Saving
Solution
Welcome Message
Edit Welcome Message
Logo
13
Hospitality Logo
/Message
Hospitality Logo DL
Logo Display Time
Clone TV to USB
Clone USB to TV
14 Cloning
Setting Auto Intialize
REACH 3.0
REACH 2.0
REACH Channel
Group ID
REACH
15
Solution REACH Update Time
REACH Update
Immediate
Room Number
REACH 2.0 TV Sound
REACH 2.0 Server
Network Setup
SmartHub Model
16 Network
SmartHub Setting
initial value
2
6
OFF
...
ON
OFF
OFF
OFF
...
...
OFF
OFF
OFF
...
...
Ticker OFF
...
...
...
...
...
Version
Setting
Description
Determines the Sub AMP operation mode.
− 0 : Turns the Sub AMP function off (PWM off).
− 1 : Determines the Sub volume according to the main volume control.
That is, the sub volume is determined according to the Power On Volume, the Min
Volume, and the Max.
− 2 : Determines the volume according to the bathroom control panel setting.
y HG890V model only can select 0 and 1.
Sub AMP Volume level at power on initial condition.
For the specific situation, pls see the table below.
This feature adjusts the brightness of the TV in order to reduce power
consumption.
− Off : Turns off the energy saving function.
− Low : Sets the TV to low energy saving mode.
− Medium : Sets the TV to medium energy saving mode.
− High : Sets the TV to high energy saving mode.
Display Welcome Message.
Edit Welcome Message.
User can set the logo display Off or the type of logo file(BMP/AVI). (Can't use at
the same time with "Welcome Message")
Download the logo file from USB toTV.
Set the logo display time (3/5/7 Seconds).
USB Clone: TV → USB
USB Clone: USB → TV
When Setting Auto Initialize is set to On, and the power is turned off and on or
the Master Power is turned off and on, the data is restored to the cloned values.
If there is no cloned value, even when the Setting Auto Initialize is set to On, it will
be ignored and the operation will be the same as that whenSetting Auto Initialize
is set to Off.
− OFF : Close REACH 3.0.
− ON : Open REACH 3.0.
− OFF : Close REACH 2.0.
− ON : Open REACH 2.0.
87:Assign a DTV channel number to carry the update REACH data. This channel
number must be the same as the number set on the Reach server.
All:Select the group ID of the REACH server. (Refer to the REACH server manual
for more details)
− ON : The TICKER content is displayed.
− OFF : The TICKER content is not displayed.
Lets you set when data such as updated SW, cloning files, and S-LYNC REACH
contents is downloaded from the REACH server to the TV :
− hour : Every hour.
− 2hour : Every 2 hours.
− 12:00 am : every 12:00 a.m.
− 2:00 am: every 2:00 a.m.
− 12:00 pm : every 12:00 p.m.
− 2:00 pm : every 2:00 p.m.
− ON : Whenever the TV enters standby mode (the power cord is plugged in
and the power is off), the REACH data is updated on the TV.
− OFF : The REACH data is only updated on the TV at the REACH server
update time.
Setting Room Number.
− OFF: Close REACH 2.0 TV Sound.
− ON: Open REACH 2.0 TV Sound.
0000: Displays the current REACH data version.
Set IP address to establish Internet connection.
Set Hotel ID.
Enter to Smart Hub setting interface.
31
English