Advertisement
PROGRAMME
SELECTION
AND SPECIAL FUNCTIONS
When you have selected the desired
programme and any option buttons, the
information you have selected will appear
on the display.
When programmes and option buttons are
compatible a bleeping sound will be heard
and the LED above the option button
selected remain illuminated.
If you select an option button that is not
compatible with the programme you
require, the LED above the button will not
switch on and "NOT AVAILABLE" will be
displayed.
To deselect an option button, press it
again.
Carefully read the relevant descriptions
detailed below.
Programme settings
■ Open the door and place dirty dishes
inside the appliance.
■ Press the "ON/OFF" button
.
■ After pressing the "ON/OFF" button,
the
LED
for
the
factory
set
"recommended" (which is ideal for full
load daily use) or the LED for the Auto'
Memory program will blink.
The left section of the display will
show the length of the programme
alternating
hours
with
minutes
(I.e.: 1 h = 1 hour / 40 = 40 minutes).
The middle section of the display will
show the programme selected and, after
it has started, the programme phase.
The right section of the display will
show the maximum temperature of
selected programme.
Example:
"Recommended" programme
(factory setting)
AUTO PROG.
1h
UNIVERSAL
Length of programme/
Time remaining
11:05
40
PREWASH
IMPORTANT
The dishwasher has two very useful
functions:
- the "recommended" programme
(
) for quick and safe selection;
- the "Auto' Memory", function
which memorises a programme
used at least 3 times consecutively
so that if you regularly use the same
washing cycle you do not have to
keep setting the programme each
time, thereby saving time and effort.
is
■ To choose an option, press the
corresponding button (the LED will
switch on). The selected option will be
displayed (if you choose more than one
option at the same time, they will be
displayed one after the other).
Option buttons must be pressed
BEFORE starting the programme to
get them be accepted.
■ To choose another programme, press
the corresponding button (the relevant
LED will flash confirming the selection).
24
■ To start the programme, press the
selected program button again to
confirm.
The programme starts automatically, the
relevant LED will stop blinking and
remain on.
The display will show the going
65
programme phase and time remaining to
the end that is automatically updated
during running.
Maximum
temperature
If the operations described previously
are made while the door is open, the
programme will not start until the door
65
is closed.
"AUTOMATIC" programmes
The dishwasher is equipped with a dirt
sensor, able to analyse water murkiness
during all "AUTOMATIC" program phases
(see program list); thanks to this sensor the
washing cycle parameters are automatically
adapted to the real quantity of dirt on
dishes. Thus excellent washing results are
guaranteed while optimising water and
energy consumption.
Programme interruption
Opening the door when a program is
running is not recommended especially
during the main washing and final hot rinse
phases. However, if the door is opened
while a program is running (for example, to
add dishes) the machine stops automatically.
Close the door, without pressing any
buttons. The cycle will start from where it
left off (if it is necessary, the appliance
will make a short thermal anti-shock
programme before).
IMPORTANT
A running program can be interrupted
without opening the door by pausing
the dishwasher.
To pause, hold the running program
button down for at least 3 seconds
and release when the corresponding
LED starts blinking and the display
will show that the programme is
paused.
Simply press the program button
again to restart the cycle from where
it left off (the LED will stop blinking
and remain on).
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
Changing a running programme
Proceed as follows to change or cancel a
running programme:
■ Hold down the current programme
button (with the LED on) for at least 5
seconds. All programmes LEDs will turn
on for one second. The running
programme will be cancelled and the
corresponding LED will start blinking.
The display will show that the programme
has been cancelled and, eventually, that
water drain is necessary.
■ At this point a new programme can be
set.
15 seconds after the programme has
been cancelled and no new settings are
made , all LEDs will switch off and the
current time will be displayed alone.
25
Advertisement
