Advertisement
■ To start the countdown, press the
selected programme button again to
confirm (the relevant LED will stop
blinking and remain on and the setting
programme end time will be displayed ).
At the end of the countdown, the programme
will automatically start and the programme
phase of the selected cycle will be shown
in the display.
If "BLACKOUT" appears on the display,
please see the "AUTOMATIC FAULT
SIGNALS" section.
WARNING!
"INTER@CT
3D" calculates the
MAXIMUM time necessary to end the
required programme, according to
selected options. However, during
running programme, due to some
variable parameters like loading
size
and
mix,
incoming
water
temperature, selection of automatic
programmes, dirtiness of dishes, the
EFFECTIVE TIME to cycle end may
be shorter than forecast. The REAL
TIME of programme end may be few
minutes earlier.
Setting with "SET TIME MODE
RELATIVE"
IMPORTANT
Choosing the "SET TIME MODE
RELATIVE" the "DELAY START"
option is available only.
("DELAY START")
■ Press the "MENU" button ("00h" will
appear on the display).
■ Press the button again to increase the
delay in hours (each time the button is
pressed the delay is increased by 1 hour
to a maximum of 23).
Example:
if at 13:00 you wish the programme to start
at 17:30, set 04h.
DELAY
START 04h
■ To start the countdown, press the
selected programme button again to
confirm (the relevant LED will stop
blinking and remain on and the start time
delay will be displayed).
At the end of the countdown, the programme
will automatically start and the programme
phase of the selected cycle will be
displayed.
In case of power failure, the "DELAY
START" function re-starts with the
delay time at the same value just before
the power failure.
Cancelling the "PROGRAMME START"
/"PROGRAMME END" or "DELAY
START"
If the countdown has NOT already been
activated the "PROGRAMME START"/
"PROGRAMME END" or "DELAY START
can be cancelled proceeding as follows :
■ Hold down the "MENU" button until the
selected programme will be displayed
again.
If the countdown has already been
activated the "PROGRAMME START"/
"PROGRAMME END" or "DELAY START
can be cancelled proceeding as follows :
■ Hold the selected program button down
for at least 5 seconds.
28
■ Delayed start cancellation is confirmed
when the selected programme LED
starts to blink and the selected programme
will displayed again (any selected
options will also be cancelled and the
corresponding LEDs will turn off).
■ At this point, a new program and option
button must be set to start a new
programme
as
indicated
in
"PROGRAMME SETTINGS" section.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically empty any excess
water should a problem occur.
The dishwasher is able to signal a series of faults in the display.
AUTOMATIC FAULT SIGNALS
FAULTS
E2
No water (Inlet hose closed).
appears on the display and
the buzzer sounds.
E3
The machine cannot drain water.
appears on the display and
the buzzer sounds.
E4
Water leak
appears on the display and
the buzzer sounds.
E5
Electronic temperature control fault.
appears on the display and
the buzzer sounds.
E6
Electronic control fault.
appear on the display and
the buzzer sounds.
E8
Ei
The water-heating element is not
or
appear on the display
working correctly or the filter plate is
and the buzzer sounds.
clogged.
"BLACKOUT"
The power failure occurs during
appears on the
countdown for "PROGRAMME
display.
START" or for "PROGRAMME END".
WARNING!
To ensure the correct operation of
the anti-overflow safety device, it is
recommended not to move or to tilt
the dishwasher during operation.
If it is necessary to move or to tilt
the dishwasher, first make sure the
washing cycle is finished and that
the
no water is left in the tank.
CAUSE
SOLUTION
Turn off the dishwasher, open the
inlet hose and reset the cycle.
Check if the drain tube is bent or if
the siphon or filters are clogged.
If the problem persists, contact
Customer Service.
Check if the drain tube is bent or if
the siphon or filters are clogged.
If the problem persists, contact
Customer Service.
Contact Customer Service.
Contact Customer Service.
Clean the filter plate.
If the problem persists, contact
Customer Service.
Re-set the required programme.
29
Advertisement
