Advertisement
WHEN USING YOUR NEW
"INTER@CT 3D" FOR THE
FIRST TIME
This dishwasher will operate even without
programming the "INTER@CT 3D" set up.
However, this machine has "PROGRAMME
START" / "PROGRAMME END" and
"DELAY START" functions that must be
programmed to make "INTER@CT 3D" to
work properly.
A
GUIDE
AROUND
YOUR
"INTER@CT 3D"
Connect product up to the electric / water
supplies and drainage and press the
"ON/OFF" button
.
When the appliance has been switched on,
the display shows:
Start screen
WELCOME !
After 3 seconds the display will show:
H M 11:05
Accurate time can be reset later.
Then, the "recommended" programme
will be displayed alternately to time.
"Recommended" programme
(factory setting)
AUTO PROG.
1h
65
UNIVERSAL
Maximum
Programme
temperature
length
40
65
11:05
IMPORTANTE
Before entering the "INTER@CT 3D"
menu, please note you have 30
seconds per operation to make your
selection. Should you run out of time
the display will return to the start
screen, and you simply have to
re-enter the "INTER@CT 3D" menu to
continue with programming.
Contents of INTER@CT 3D menu
Step 1: "LANGUAGE"
Step 2: "DISPLAY CONTRAST "
Step 3: "WATER HARDNESS"
(REGULATING THE WATER SOFTENER)
Step 4: "SET NEW TIME"
Step 5: "SET TIME MODE"
("ABSOLUTE" O "RELATIVE")
Step 6: "BUZZER"
Step 7: "ENABLE MEMORY"
Step 8: "SET DEMO MODE"
Step 9: "DOMOTIC MODE"
Step 10: "EXIT MENU"
Note:
The "INTER@CT 3D" menu is sequential.
Example:
If you want to enter Step 4 ("SET NEW
TIME") to update time, you must go
through step 1,2 and 3 by pressing the
"MENU" button.
20
PROGRAMMING
THE DISHWASHER
"INTER@CT 3D" needs to be programmed
so that the correct clock setting, language
and personal requirements are set.
Enter the "INTER@CT 3D" menu
Hold down the "TIME SAVER" and the
"BOOST" buttons together for 5 seconds
or until the beep sounds.
The display will show:
STEP 1
CHOIX LANGUE
FRANCAIS
(Default setting: FRENCH)
If you would like to select another language,
press the "FLEXI LOAD" button until the
favourite language is displayed.
CHOIX LANGUE
ENGLISH
Press the "MENU" button to confirm and
move to the next step.
STEP 2
DISPLAY
CONTRAST
To increase the display contrast, press the
"FLEXI LOAD" button.
To decrease the display contrast, press the
"BOOST" button.
Press the "MENU" button to confirm and
move to the next step.
STEP 3
WATER HARDNESS
LEVEL 4
(Default setting: LEVEL 4)
To increase the water softener setting level
press the "FLEXI LOAD" button.
To decrease the water softener setting
level press the "BOOST" button.
FOR MORE INFORMATION ABOUT
WATER SOFTENER SETTING LEVEL,
PLEASE SEE "WATER SOFTENER
UNIT" SECTION.
Press the "MENU" button to confirm and
move to the next step.
STEP 4
SET NEW TIME
11:05
This function needs to be set for two
reasons: firstly to display the current
time on the screen and secondly to
make the "PROGRAMME START" or
"PROGRAMME END" settings to work
properly.
To increase the hour press the "BOOST"
button.
To increase the minutes press the "FLEXI
LOAD" button.
Press the "MENU" button to confirm and
move to the next step.
STEP 5
SET TIME MODE
RELATIVE
(Default setting: RELATIVE)
The "DELAY START" can be set in two
different ways ("ABSOLUTE" or "RELATIVE")
while the "PROGRAMME END" can be set
only in "RELATIVE" time mode.
21
Advertisement
