After Self-Cleaning; Care And Cleaning; Cleaning Agents; Detaching And Refitting The Rails - Siemens HB73GB550 Instruction Manual

Setting a later end time
The end time of the self-cleaning programme can be delayed.
In this way, self-cleaning can run overnight, for example, so that
you can use your oven during the day.
Make the settings as described in steps 1 and 2. Before the
oven starts, use the or
@ A
The oven switches to standby. The display shows the time at
which self-cleaning will end and the

Care and cleaning

With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
Slight differences in the colours on the front of the oven are
■
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
■
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
■
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.

Cleaning agents

To ensure that the different surfaces are not damaged by using
the wrong type of cleaning agent, observe the information in the
table. Do not use
harsh or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
■
Wash new sponge cloths thoroughly before use.
Area Cleaning agents
Oven front Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Do not use glass cleaners or glass
scrapers.
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Remove traces of limescale, grease,
starch and albumin (e.g. egg white) immedi-
ately. Corrosion can form under such resi-
dues.
Special stainless steel cleaning products
suitable for hot surfaces are available from
our after-sales service or from specialist
retailers. Apply a very thin layer of the
cleaning product with a soft cloth.
Door panels Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Door cover Stainless steel cleaning agents (available
from our after-sales service or from special-
ist retailers):
Please observe the manufacturer's instruc-
tions.
14
button to set a later end time.
N arrow is next to the
symbol. When self-cleaning starts, you can see the time
counting down and the
The symbol goes out.
y

After self-cleaning

Once the cooking compartment has cooled down, wipe out the
ash that has been left behind in the cooking compartment with
a damp cloth.
y
Area
Cooking com-
partment
Glass cover for
the oven light
Rails
Telescopic
shelves
Accessories

Detaching and refitting the rails

The rails can be removed for cleaning. The oven must have
cooled down.
Detaching the rails
Lift up the front of the rail
1.
and unhook it (figure A).
2.
Then pull the whole rail forward
3.
and remove it (Fig. B).
4.
Clean the rails with cleaning agent and a sponge. For stubborn
deposits of dirt, use a brush.
arrow is next to the
N
Cleaning agents
Hot soapy water or a vinegar solution:
Clean with a dish cloth.
If there are heavy deposits of dirt, use a
stainless steel scouring pad or oven
cleaner. Only use when the cooking com-
partment is cold.
It is best to use the self-cleaning function.
Observe the instructions in the Self-cleaning
section when doing so.
Hot soapy water:
Clean with a dish cloth.
Hot soapy water:
Soak and clean with a dish cloth or brush.
Hot soapy water:
Clean with a dish cloth or a brush.
Do not remove the lubricant while the pull-
out rails are pulled out – it is best to clean
them when they are inserted. Do not soak,
clean in the dishwasher, or leave in the
oven during self-cleaning. The rails may be
damaged causing them to jam.
Hot soapy water:
Soak and clean with a dish cloth or brush.
symbol.
x